#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */
#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */
-/* default combinations */
-#define DCMD_RXPCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_RXMCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_TXPCDR (DCMD_INCSRCADDR|DCMD_FLOWTRG|DCMD_BURST32|DCMD_WIDTH4)
-
/*
* UARTs
*/
/* FIXME: This clash with SA1111 defines */
-#ifndef CONFIG_SA1111
+#ifndef _ASM_ARCH_SA1111
+
#define SACR0 __REG(0x40400000) /* Global Control Register */
#define SACR1 __REG(0x40400004) /* Serial Audio I 2 S/MSB-Justified Control Register */
#define SASR0 __REG(0x4040000C) /* Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
#define SAICR __REG(0x40400018) /* Serial Audio Interrupt Clear Register */
#define SADIV __REG(0x40400060) /* Audio Clock Divider Register. */
#define SADR __REG(0x40400080) /* Serial Audio Data Register (TX and RX FIFO access Register). */
-#endif
-#define SACR0_RFTH(x) (x << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */
-#define SACR0_TFTH(x) (x << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */
-#define SACR0_STRF (1 << 5) /* FIFO Select for EFWR Special Function */
-#define SACR0_EFWR (1 << 4) /* Enable EFWR Function */
-#define SACR0_RST (1 << 3) /* FIFO, i2s Register Reset */
-#define SACR0_BCKD (1 << 2) /* Bit Clock Direction */
-#define SACR0_ENB (1 << 0) /* Enable I2S Link */
-
-#define SACR1_ENLBF (1 << 5) /* Enable Loopback */
-#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */
-#define SACR1_DREC (1 << 3) /* Disable Recording Function */
-#define SACR1_AMSL (1 << 1) /* Specify Alternate Mode */
-
-#define SASR0_I2SOFF (1 << 7) /* Controller Status */
-#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */
-#define SASR0_TUR (1 << 5) /* Tx FIFO Underrun */
-#define SASR0_RFS (1 << 4) /* Rx FIFO Service Request */
-#define SASR0_TFS (1 << 3) /* Tx FIFO Service Request */
-#define SASR0_BSY (1 << 2) /* I2S Busy */
-#define SASR0_RNE (1 << 1) /* Rx FIFO Not Empty */
-#define SASR0_TNF (1 << 0) /* Tx FIFO Not Empty */
-
-#define SADIV_3_058M 0x0c /* Serial Clock Divider 3.058MHz */
-#define SADIV_2_836M 0x0d /* 2.836 MHz */
-#define SADIV_1_405M 0x1a /* 1.405 MHz */
-#define SADIV_1_026M 0x24 /* 1.026 MHz */
-#define SADIV_702K 0x34 /* 702 kHz */
-#define SADIV_513K 0x48 /* 513 kHz */
-
-#define SAICR_ROR (1 << 6) /* Clear Rx FIFO Overrun Interrupt */
-#define SAICR_TUR (1 << 5) /* Clear Tx FIFO Underrun Interrupt */
-
-#define SAIMR_ROR (1 << 6) /* Enable Rx FIFO Overrun Condition Interrupt */
-#define SAIMR_TUR (1 << 5) /* Enable Tx FIFO Underrun Condition Interrupt */
-#define SAIMR_RFS (1 << 4) /* Enable Rx FIFO Service Interrupt */
-#define SAIMR_TFS (1 << 3) /* Enable Tx FIFO Service Interrupt */
+#define SACR0_RFTH(x) (x << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_TFTH(x) (x << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_STRF (1 << 5) /* FIFO Select for EFWR Special Function */
+#define SACR0_EFWR (1 << 4) /* Enable EFWR Function */
+#define SACR0_RST (1 << 3) /* FIFO, i2s Register Reset */
+#define SACR0_BCKD (1 << 2) /* Bit Clock Direction */
+#define SACR0_ENB (1 << 0) /* Enable I2S Link */
+#define SACR1_ENLBF (1 << 5) /* Enable Loopback */
+#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */
+#define SACR1_DREC (1 << 3) /* Disable Recording Function */
+#define SACR1_AMSL (1 << 1) /* Specify Alternate Mode */
+
+#define SASR0_I2SOFF (1 << 7) /* Controller Status */
+#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */
+#define SASR0_TUR (1 << 5) /* Tx FIFO Underrun */
+#define SASR0_RFS (1 << 4) /* Rx FIFO Service Request */
+#define SASR0_TFS (1 << 3) /* Tx FIFO Service Request */
+#define SASR0_BSY (1 << 2) /* I2S Busy */
+#define SASR0_RNE (1 << 1) /* Rx FIFO Not Empty */
+#define SASR0_TNF (1 << 0) /* Tx FIFO Not Empty */
+
+#define SAICR_ROR (1 << 6) /* Clear Rx FIFO Overrun Interrupt */
+#define SAICR_TUR (1 << 5) /* Clear Tx FIFO Underrun Interrupt */
+
+#define SAIMR_ROR (1 << 6) /* Enable Rx FIFO Overrun Condition Interrupt */
+#define SAIMR_TUR (1 << 5) /* Enable Tx FIFO Underrun Condition Interrupt */
+#define SAIMR_RFS (1 << 4) /* Enable Rx FIFO Service Interrupt */
+#define SAIMR_TFS (1 << 3) /* Enable Tx FIFO Service Interrupt */
+#endif
/*
* AC97 Controller registers
#define POCR __REG(0x40500000) /* PCM Out Control Register */
#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define PICR __REG(0x40500004) /* PCM In Control Register */
#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MCCR __REG(0x40500008) /* Mic In Control Register */
#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define GCR __REG(0x4050000C) /* Global Control Register */
+#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
#define POSR __REG(0x40500010) /* PCM Out Status Register */
#define POSR_FIFOE (1 << 4) /* FIFO error */
+#define POSR_FSR (1 << 2) /* FIFO Service Request */
#define PISR __REG(0x40500014) /* PCM In Status Register */
#define PISR_FIFOE (1 << 4) /* FIFO error */
+#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define PISR_FSR (1 << 2) /* FIFO Service Request */
#define MCSR __REG(0x40500018) /* Mic In Status Register */
#define MCSR_FIFOE (1 << 4) /* FIFO error */
+#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MCSR_FSR (1 << 2) /* FIFO Service Request */
#define GSR __REG(0x4050001C) /* Global Status Register */
#define GSR_CDONE (1 << 19) /* Command Done */
#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */
#define GSR_SCR (1 << 9) /* Secondary Codec Ready */
#define GSR_PCR (1 << 8) /* Primary Codec Ready */
-#define GSR_MINT (1 << 7) /* Mic In Interrupt */
+#define GSR_MCINT (1 << 7) /* Mic In Interrupt */
#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
+#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */
#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
#define MOCR __REG(0x40500100) /* Modem Out Control Register */
#define MOCR_FEIE (1 << 3) /* FIFO Error */
+#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MICR __REG(0x40500108) /* Modem In Control Register */
#define MICR_FEIE (1 << 3) /* FIFO Error */
+#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MOSR __REG(0x40500110) /* Modem Out Status Register */
#define MOSR_FIFOE (1 << 4) /* FIFO error */
+#define MOSR_FSR (1 << 2) /* FIFO Service Request */
#define MISR __REG(0x40500118) /* Modem In Status Register */
#define MISR_FIFOE (1 << 4) /* FIFO error */
+#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MISR_FSR (1 << 2) /* FIFO Service Request */
#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */
#define GPIO31_SYNC 31 /* AC97/I2S sync */
#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */
+#define GPIO32_SYSCLK 32 /* I2S System Clock */
#define GPIO32_MMCCLK 32 /* MMC Clock (PXA270) */
#define GPIO33_nCS_5 33 /* chip select 5 */
#define GPIO34_FFRXD 34 /* FFUART receive */
#define GPIO111_MMCDAT3 111 /* MMC DAT3 (PXA27x) */
#define GPIO111_MMCCS1 111 /* MMC Chip Select 1 (PXA27x) */
#define GPIO112_MMCCMD 112 /* MMC CMD (PXA27x) */
+#define GPIO113_I2S_SYSCLK 113 /* I2S System Clock (PXA27x) */
#define GPIO113_AC97_RESET_N 113 /* AC97 NRESET on (PXA27x) */
/* GPIO alternate function mode & direction */
#define GPIO18_RDY_MD (18 | GPIO_ALT_FN_1_IN)
#define GPIO19_DREQ1_MD (19 | GPIO_ALT_FN_1_IN)
#define GPIO20_DREQ0_MD (20 | GPIO_ALT_FN_1_IN)
-#define GPIO23_SCLK_md (23 | GPIO_ALT_FN_2_OUT)
+#define GPIO23_SCLK_MD (23 | GPIO_ALT_FN_2_OUT)
#define GPIO24_SFRM_MD (24 | GPIO_ALT_FN_2_OUT)
#define GPIO25_STXD_MD (25 | GPIO_ALT_FN_2_OUT)
#define GPIO26_SRXD_MD (26 | GPIO_ALT_FN_1_IN)
#define GPIO27_SEXTCLK_MD (27 | GPIO_ALT_FN_1_IN)
#define GPIO28_BITCLK_AC97_MD (28 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_I2S_MD (28 | GPIO_ALT_FN_2_IN)
+#define GPIO28_BITCLK_IN_I2S_MD (28 | GPIO_ALT_FN_2_IN)
+#define GPIO28_BITCLK_OUT_I2S_MD (28 | GPIO_ALT_FN_1_OUT)
#define GPIO29_SDATA_IN_AC97_MD (29 | GPIO_ALT_FN_1_IN)
#define GPIO29_SDATA_IN_I2S_MD (29 | GPIO_ALT_FN_2_IN)
#define GPIO30_SDATA_OUT_AC97_MD (30 | GPIO_ALT_FN_2_OUT)
#define GPIO30_SDATA_OUT_I2S_MD (30 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT)
+#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN)
+#define GPIO32_SYSCLK_I2S_MD (32 | GPIO_ALT_FN_1_OUT)
#define GPIO32_MMCCLK_MD ( 32 | GPIO_ALT_FN_2_OUT)
#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT)
#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN)
#define GPIO111_MMCDAT3_MD (111 | GPIO_ALT_FN_1_OUT)
#define GPIO110_MMCCS1_MD (111 | GPIO_ALT_FN_1_OUT)
#define GPIO112_MMCCMD_MD (112 | GPIO_ALT_FN_1_OUT)
+#define GPIO113_I2S_SYSCLK_MD (113 | GPIO_ALT_FN_1_OUT)
#define GPIO113_AC97_RESET_N_MD (113 | GPIO_ALT_FN_2_OUT)
#define GPIO117_I2CSCL_MD (117 | GPIO_ALT_FN_1_OUT)
#define GPIO118_I2CSDA_MD (118 | GPIO_ALT_FN_1_IN)
#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */
/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
+#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
git://git.onelab.eu / linux-2.6.git / blobdiff