* published by the Free Software Foundation.
*/
-#include <linux/config.h>
-
-// FIXME hack so that SA-1111.h will work [cb]
+#ifndef __PXA_REGS_H
+#define __PXA_REGS_H
-#ifndef __ASSEMBLY__
-typedef unsigned short Word16 ;
-typedef unsigned int Word32 ;
-typedef Word32 Word ;
-typedef Word Quad [4] ;
-typedef void *Address ;
-typedef void (*ExcpHndlr) (void) ;
-#endif
+#include <linux/config.h>
/*
* PXA Chip selects
#define DCSR_RUN (1 << 31) /* Run Bit (read / write) */
#define DCSR_NODESC (1 << 30) /* No-Descriptor Fetch (read / write) */
#define DCSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */
+#ifdef CONFIG_PXA27x
+#define DCSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */
+#define DCSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */
+#define DCSR_EORSTOPEN (1 << 26) /* STOP on an EOR */
+#define DCSR_SETCMPST (1 << 25) /* Set Descriptor Compare Status */
+#define DCSR_CLRCMPST (1 << 24) /* Clear Descriptor Compare Status */
+#define DCSR_CMPST (1 << 10) /* The Descriptor Compare Status */
+#define DCSR_ENRINTR (1 << 9) /* The end of Receive */
+#endif
#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */
#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */
#define DCSR_ENDINTR (1 << 2) /* End Interrupt (read / write) */
#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
+#define DALGN __REG(0x400000a0) /* DMA Alignment Register */
#define DINT __REG(0x400000f0) /* DMA Interrupt Register */
+#define DRCMR(n) __REG2(0x40000100, (n)<<2)
#define DRCMR0 __REG(0x40000100) /* Request to Channel Map Register for DREQ 0 */
#define DRCMR1 __REG(0x40000104) /* Request to Channel Map Register for DREQ 1 */
#define DRCMR2 __REG(0x40000108) /* Request to Channel Map Register for I2S receive Request */
#define DRCMR12 __REG(0x40000130) /* Request to Channel Map Register for AC97 audio transmit Request */
#define DRCMR13 __REG(0x40000134) /* Request to Channel Map Register for SSP receive Request */
#define DRCMR14 __REG(0x40000138) /* Request to Channel Map Register for SSP transmit Request */
-#define DRCMR15 __REG(0x4000013c) /* Reserved */
-#define DRCMR16 __REG(0x40000140) /* Reserved */
+#define DRCMR15 __REG(0x4000013c) /* Request to Channel Map Register for SSP2 receive Request */
+#define DRCMR16 __REG(0x40000140) /* Request to Channel Map Register for SSP2 transmit Request */
#define DRCMR17 __REG(0x40000144) /* Request to Channel Map Register for ICP receive Request */
#define DRCMR18 __REG(0x40000148) /* Request to Channel Map Register for ICP transmit Request */
#define DRCMR19 __REG(0x4000014c) /* Request to Channel Map Register for STUART receive Request */
#define DRCMR37 __REG(0x40000194) /* Request to Channel Map Register for USB endpoint 13 Request */
#define DRCMR38 __REG(0x40000198) /* Request to Channel Map Register for USB endpoint 14 Request */
#define DRCMR39 __REG(0x4000019C) /* Reserved */
+#define DRCMR66 __REG(0x40001108) /* Request to Channel Map Register for SSP3 receive Request */
+#define DRCMR67 __REG(0x4000110C) /* Request to Channel Map Register for SSP3 transmit Request */
+#define DRCMR68 __REG(0x40001110) /* Request to Channel Map Register for Camera FIFO 0 Request */
+#define DRCMR69 __REG(0x40001114) /* Request to Channel Map Register for Camera FIFO 1 Request */
+#define DRCMR70 __REG(0x40001118) /* Request to Channel Map Register for Camera FIFO 2 Request */
#define DRCMRRXSADR DRCMR2
#define DRCMRTXSADR DRCMR3
#define DRCMRTXPCDR DRCMR12
#define DRCMRRXSSDR DRCMR13
#define DRCMRTXSSDR DRCMR14
+#define DRCMRRXSS2DR DRCMR15
+#define DRCMRTXSS2DR DRCMR16
#define DRCMRRXICDR DRCMR17
#define DRCMRTXICDR DRCMR18
#define DRCMRRXSTRBR DRCMR19
#define DRCMRTXSTTHR DRCMR20
#define DRCMRRXMMC DRCMR21
#define DRCMRTXMMC DRCMR22
+#define DRCMRRXSS3DR DRCMR66
+#define DRCMRTXSS3DR DRCMR67
+#define DRCMRUDC(x) DRCMR((x) + 24)
#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */
-#define DRCMR_CHLNUM 0x0f /* mask for Channel Number (read / write) */
+#define DRCMR_CHLNUM 0x1f /* mask for Channel Number (read / write) */
#define DDADR0 __REG(0x40000200) /* DMA Descriptor Address Register Channel 0 */
#define DSADR0 __REG(0x40000204) /* DMA Source Address Register Channel 0 */
#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */
#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */
-/* default combinations */
-#define DCMD_RXPCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_RXMCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_TXPCDR (DCMD_INCSRCADDR|DCMD_FLOWTRG|DCMD_BURST32|DCMD_WIDTH4)
-
/*
* UARTs
#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
+/* Hardware UART (HWUART) */
+#define HWUART HWRBR
+#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */
+#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */
+#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */
+#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */
+#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */
+#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */
+#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */
+#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */
+#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */
+#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */
+#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */
+#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */
+#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */
+#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */
+#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
#define IER_DMAE (1 << 7) /* DMA Requests Enable */
#define IER_UUE (1 << 6) /* UART Unit Enable */
#define IER_NRZE (1 << 5) /* NRZ coding Enable */
#define ISR __REG(0x40301698) /* I2C Status Register - ISR */
#define ISAR __REG(0x403016A0) /* I2C Slave Address Register - ISAR */
+#define PWRIBMR __REG(0x40f00180) /* Power I2C Bus Monitor Register-IBMR */
+#define PWRIDBR __REG(0x40f00188) /* Power I2C Data Buffer Register-IDBR */
+#define PWRICR __REG(0x40f00190) /* Power I2C Control Register - ICR */
+#define PWRISR __REG(0x40f00198) /* Power I2C Status Register - ISR */
+#define PWRISAR __REG(0x40f001A0) /*Power I2C Slave Address Register-ISAR */
+
#define ICR_START (1 << 0) /* start bit */
#define ICR_STOP (1 << 1) /* stop bit */
#define ICR_ACKNAK (1 << 2) /* send ACK(0) or NAK(1) */
*/
/* FIXME: This clash with SA1111 defines */
-#ifndef CONFIG_SA1111
+#ifndef _ASM_ARCH_SA1111
+
#define SACR0 __REG(0x40400000) /* Global Control Register */
#define SACR1 __REG(0x40400004) /* Serial Audio I 2 S/MSB-Justified Control Register */
#define SASR0 __REG(0x4040000C) /* Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
#define SAICR __REG(0x40400018) /* Serial Audio Interrupt Clear Register */
#define SADIV __REG(0x40400060) /* Audio Clock Divider Register. */
#define SADR __REG(0x40400080) /* Serial Audio Data Register (TX and RX FIFO access Register). */
-#endif
+#define SACR0_RFTH(x) (x << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_TFTH(x) (x << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_STRF (1 << 5) /* FIFO Select for EFWR Special Function */
+#define SACR0_EFWR (1 << 4) /* Enable EFWR Function */
+#define SACR0_RST (1 << 3) /* FIFO, i2s Register Reset */
+#define SACR0_BCKD (1 << 2) /* Bit Clock Direction */
+#define SACR0_ENB (1 << 0) /* Enable I2S Link */
+#define SACR1_ENLBF (1 << 5) /* Enable Loopback */
+#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */
+#define SACR1_DREC (1 << 3) /* Disable Recording Function */
+#define SACR1_AMSL (1 << 0) /* Specify Alternate Mode */
+
+#define SASR0_I2SOFF (1 << 7) /* Controller Status */
+#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */
+#define SASR0_TUR (1 << 5) /* Tx FIFO Underrun */
+#define SASR0_RFS (1 << 4) /* Rx FIFO Service Request */
+#define SASR0_TFS (1 << 3) /* Tx FIFO Service Request */
+#define SASR0_BSY (1 << 2) /* I2S Busy */
+#define SASR0_RNE (1 << 1) /* Rx FIFO Not Empty */
+#define SASR0_TNF (1 << 0) /* Tx FIFO Not Empty */
+
+#define SAICR_ROR (1 << 6) /* Clear Rx FIFO Overrun Interrupt */
+#define SAICR_TUR (1 << 5) /* Clear Tx FIFO Underrun Interrupt */
+
+#define SAIMR_ROR (1 << 6) /* Enable Rx FIFO Overrun Condition Interrupt */
+#define SAIMR_TUR (1 << 5) /* Enable Tx FIFO Underrun Condition Interrupt */
+#define SAIMR_RFS (1 << 4) /* Enable Rx FIFO Service Interrupt */
+#define SAIMR_TFS (1 << 3) /* Enable Tx FIFO Service Interrupt */
+
+#endif
/*
* AC97 Controller registers
#define POCR __REG(0x40500000) /* PCM Out Control Register */
#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define PICR __REG(0x40500004) /* PCM In Control Register */
#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MCCR __REG(0x40500008) /* Mic In Control Register */
#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define GCR __REG(0x4050000C) /* Global Control Register */
+#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
#define POSR __REG(0x40500010) /* PCM Out Status Register */
#define POSR_FIFOE (1 << 4) /* FIFO error */
+#define POSR_FSR (1 << 2) /* FIFO Service Request */
#define PISR __REG(0x40500014) /* PCM In Status Register */
#define PISR_FIFOE (1 << 4) /* FIFO error */
+#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define PISR_FSR (1 << 2) /* FIFO Service Request */
#define MCSR __REG(0x40500018) /* Mic In Status Register */
#define MCSR_FIFOE (1 << 4) /* FIFO error */
+#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MCSR_FSR (1 << 2) /* FIFO Service Request */
#define GSR __REG(0x4050001C) /* Global Status Register */
#define GSR_CDONE (1 << 19) /* Command Done */
#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */
#define GSR_SCR (1 << 9) /* Secondary Codec Ready */
#define GSR_PCR (1 << 8) /* Primary Codec Ready */
-#define GSR_MINT (1 << 7) /* Mic In Interrupt */
+#define GSR_MCINT (1 << 7) /* Mic In Interrupt */
#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
+#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */
#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
#define MOCR __REG(0x40500100) /* Modem Out Control Register */
#define MOCR_FEIE (1 << 3) /* FIFO Error */
+#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MICR __REG(0x40500108) /* Modem In Control Register */
#define MICR_FEIE (1 << 3) /* FIFO Error */
+#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MOSR __REG(0x40500110) /* Modem Out Status Register */
#define MOSR_FIFOE (1 << 4) /* FIFO error */
+#define MOSR_FSR (1 << 2) /* FIFO Service Request */
#define MISR __REG(0x40500118) /* Modem In Status Register */
#define MISR_FIFOE (1 << 4) /* FIFO error */
+#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MISR_FSR (1 << 2) /* FIFO Service Request */
#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
/*
* USB Device Controller
+ * PXA25x and PXA27x USB device controller registers are different.
*/
+#if defined(CONFIG_PXA25x)
+
#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */
#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */
#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */
#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
+#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */
#define UDCCS_IO_DME (1 << 3) /* DMA enable */
#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
+#elif defined(CONFIG_PXA27x)
+
+#define UDCCR __REG(0x40600000) /* UDC Control Register */
+#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */
+#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation
+ Protocol Port Support */
+#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol
+ Support */
+#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol
+ Enable */
+#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */
+#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */
+#define UDCCR_ACN_S 11
+#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */
+#define UDCCR_AIN_S 8
+#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface
+ Setting Number */
+#define UDCCR_AAISN_S 5
+#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active
+ Configuration */
+#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration
+ Error */
+#define UDCCR_UDR (1 << 2) /* UDC Resume */
+#define UDCCR_UDA (1 << 1) /* UDC Active */
+#define UDCCR_UDE (1 << 0) /* UDC Enable */
+
+#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */
+#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */
+#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */
+#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */
+
+#define UDC_INT_FIFOERROR (0x2)
+#define UDC_INT_PACKETCMP (0x1)
+
+#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
+#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */
+#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */
+#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */
+#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */
+#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */
+
+#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */
+#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */
+#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
+#define UDCISR1_IECC (1 << 31) /* IntEn - Configuration Change */
+#define UDCISR1_IESOF (1 << 30) /* IntEn - Start of Frame */
+#define UDCISR1_IERU (1 << 29) /* IntEn - Resume */
+#define UDCISR1_IESU (1 << 28) /* IntEn - Suspend */
+#define UDCISR1_IERS (1 << 27) /* IntEn - Reset */
+
+
+#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */
+#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */
+#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */
+#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt
+ Rising Edge Interrupt Enable */
+#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt
+ Falling Edge Interrupt Enable */
+#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising
+ Edge Interrupt Enable */
+#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling
+ Edge Interrupt Enable */
+#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge
+ Interrupt Enable */
+
+#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */
+
+#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */
+#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */
+#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */
+#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */
+#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */
+#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */
+#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */
+#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */
+#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */
+#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */
+#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */
+#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */
+#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */
+#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */
+
+#define UDCCSN(x) __REG2(0x40600100, (x) << 2)
+#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */
+#define UDCCSR0_SA (1 << 7) /* Setup Active */
+#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */
+#define UDCCSR0_FST (1 << 5) /* Force Stall */
+#define UDCCSR0_SST (1 << 4) /* Sent Stall */
+#define UDCCSR0_DME (1 << 3) /* DMA Enable */
+#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */
+#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */
+#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */
+
+#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */
+#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */
+#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */
+#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */
+#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */
+#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */
+#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */
+#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */
+#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */
+#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */
+#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */
+#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */
+#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */
+#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */
+#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */
+#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */
+#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */
+#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */
+#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */
+#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */
+#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */
+#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */
+#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */
+
+#define UDCCSR_DPE (1 << 9) /* Data Packet Error */
+#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */
+#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */
+#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */
+#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */
+#define UDCCSR_FST (1 << 5) /* Force STALL */
+#define UDCCSR_SST (1 << 4) /* Sent STALL */
+#define UDCCSR_DME (1 << 3) /* DMA Enable */
+#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */
+#define UDCCSR_PC (1 << 1) /* Packet Complete */
+#define UDCCSR_FS (1 << 0) /* FIFO needs service */
+
+#define UDCBCN(x) __REG2(0x40600200, (x)<<2)
+#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */
+#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */
+#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */
+#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */
+#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */
+#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */
+#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */
+#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */
+#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */
+#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */
+#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */
+#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */
+#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */
+#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */
+#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */
+#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */
+#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */
+#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */
+#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */
+#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */
+#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */
+#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */
+#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */
+#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */
+
+#define UDCDN(x) __REG2(0x40600300, (x)<<2)
+#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2))
+#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x))))
+#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */
+#define UDCDRA __REG(0x40600304) /* Data Register - EPA */
+#define UDCDRB __REG(0x40600308) /* Data Register - EPB */
+#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */
+#define UDCDRD __REG(0x40600310) /* Data Register - EPD */
+#define UDCDRE __REG(0x40600314) /* Data Register - EPE */
+#define UDCDRF __REG(0x40600318) /* Data Register - EPF */
+#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */
+#define UDCDRH __REG(0x40600320) /* Data Register - EPH */
+#define UDCDRI __REG(0x40600324) /* Data Register - EPI */
+#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */
+#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */
+#define UDCDRL __REG(0x40600330) /* Data Register - EPL */
+#define UDCDRM __REG(0x40600334) /* Data Register - EPM */
+#define UDCDRN __REG(0x40600338) /* Data Register - EPN */
+#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */
+#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */
+#define UDCDRR __REG(0x40600344) /* Data Register - EPR */
+#define UDCDRS __REG(0x40600348) /* Data Register - EPS */
+#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */
+#define UDCDRU __REG(0x40600350) /* Data Register - EPU */
+#define UDCDRV __REG(0x40600354) /* Data Register - EPV */
+#define UDCDRW __REG(0x40600358) /* Data Register - EPW */
+#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */
+
+#define UDCCN(x) __REG2(0x40600400, (x)<<2)
+#define UDCCRA __REG(0x40600404) /* Configuration register EPA */
+#define UDCCRB __REG(0x40600408) /* Configuration register EPB */
+#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */
+#define UDCCRD __REG(0x40600410) /* Configuration register EPD */
+#define UDCCRE __REG(0x40600414) /* Configuration register EPE */
+#define UDCCRF __REG(0x40600418) /* Configuration register EPF */
+#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */
+#define UDCCRH __REG(0x40600420) /* Configuration register EPH */
+#define UDCCRI __REG(0x40600424) /* Configuration register EPI */
+#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */
+#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */
+#define UDCCRL __REG(0x40600430) /* Configuration register EPL */
+#define UDCCRM __REG(0x40600434) /* Configuration register EPM */
+#define UDCCRN __REG(0x40600438) /* Configuration register EPN */
+#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */
+#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */
+#define UDCCRR __REG(0x40600444) /* Configuration register EPR */
+#define UDCCRS __REG(0x40600448) /* Configuration register EPS */
+#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */
+#define UDCCRU __REG(0x40600450) /* Configuration register EPU */
+#define UDCCRV __REG(0x40600454) /* Configuration register EPV */
+#define UDCCRW __REG(0x40600458) /* Configuration register EPW */
+#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */
+
+#define UDCCONR_CN (0x03 << 25) /* Configuration Number */
+#define UDCCONR_CN_S (25)
+#define UDCCONR_IN (0x07 << 22) /* Interface Number */
+#define UDCCONR_IN_S (22)
+#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */
+#define UDCCONR_AISN_S (19)
+#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */
+#define UDCCONR_EN_S (15)
+#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */
+#define UDCCONR_ET_S (13)
+#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */
+#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */
+#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */
+#define UDCCONR_ET_NU (0x00 << 13) /* Not used */
+#define UDCCONR_ED (1 << 12) /* Endpoint Direction */
+#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */
+#define UDCCONR_MPS_S (2)
+#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */
+#define UDCCONR_EE (1 << 0) /* Endpoint Enable */
+
+
+#define UDC_INT_FIFOERROR (0x2)
+#define UDC_INT_PACKETCMP (0x1)
+
+#define UDC_FNR_MASK (0x7ff)
+
+#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST)
+#define UDC_BCR_MASK (0x3ff)
+#endif
/*
* Fast Infrared Communication Port
*/
+#define FICP __REG(0x40800000) /* Start of FICP area */
#define ICCR0 __REG(0x40800000) /* ICP Control Register 0 */
#define ICCR1 __REG(0x40800004) /* ICP Control Register 1 */
#define ICCR2 __REG(0x40800008) /* ICP Control Register 2 */
#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */
#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */
-#define ICCR0_AME (1 << 7) /* Address match enable */
-#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */
-#define ICCR0_RIE (1 << 5) /* Receive FIFO interrupt enable */
-#define ICCR0_RXE (1 << 4) /* Receive enable */
-#define ICCR0_TXE (1 << 3) /* Transmit enable */
-#define ICCR0_TUS (1 << 2) /* Transmit FIFO underrun select */
-#define ICCR0_LBM (1 << 1) /* Loopback mode */
-#define ICCR0_ITR (1 << 0) /* IrDA transmission */
-
-#define ICSR0_FRE (1 << 5) /* Framing error */
-#define ICSR0_RFS (1 << 4) /* Receive FIFO service request */
-#define ICSR0_TFS (1 << 3) /* Transnit FIFO service request */
-#define ICSR0_RAB (1 << 2) /* Receiver abort */
-#define ICSR0_TUR (1 << 1) /* Trunsmit FIFO underun */
-#define ICSR0_EIF (1 << 0) /* End/Error in FIFO */
-
-#define ICSR1_ROR (1 << 6) /* Receiver FIFO underrun */
-#define ICSR1_CRE (1 << 5) /* CRC error */
-#define ICSR1_EOF (1 << 4) /* End of frame */
-#define ICSR1_TNF (1 << 3) /* Transmit FIFO not full */
-#define ICSR1_RNE (1 << 2) /* Receive FIFO not empty */
-#define ICSR1_TBY (1 << 1) /* Tramsmiter busy flag */
-#define ICSR1_RSY (1 << 0) /* Recevier synchronized flag */
+#define ICCR0_AME (1 << 7) /* Adress match enable */
+#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */
+#define ICCR0_RIE (1 << 5) /* Recieve FIFO interrupt enable */
+#define ICCR0_RXE (1 << 4) /* Receive enable */
+#define ICCR0_TXE (1 << 3) /* Transmit enable */
+#define ICCR0_TUS (1 << 2) /* Transmit FIFO underrun select */
+#define ICCR0_LBM (1 << 1) /* Loopback mode */
+#define ICCR0_ITR (1 << 0) /* IrDA transmission */
+
+#define ICCR2_RXP (1 << 3) /* Receive Pin Polarity select */
+#define ICCR2_TXP (1 << 2) /* Transmit Pin Polarity select */
+#define ICCR2_TRIG (3 << 0) /* Receive FIFO Trigger threshold */
+#define ICCR2_TRIG_8 (0 << 0) /* >= 8 bytes */
+#define ICCR2_TRIG_16 (1 << 0) /* >= 16 bytes */
+#define ICCR2_TRIG_32 (2 << 0) /* >= 32 bytes */
+
+#ifdef CONFIG_PXA27x
+#define ICSR0_EOC (1 << 6) /* DMA End of Descriptor Chain */
+#endif
+#define ICSR0_FRE (1 << 5) /* Framing error */
+#define ICSR0_RFS (1 << 4) /* Receive FIFO service request */
+#define ICSR0_TFS (1 << 3) /* Transnit FIFO service request */
+#define ICSR0_RAB (1 << 2) /* Receiver abort */
+#define ICSR0_TUR (1 << 1) /* Trunsmit FIFO underun */
+#define ICSR0_EIF (1 << 0) /* End/Error in FIFO */
+
+#define ICSR1_ROR (1 << 6) /* Receiver FIFO underrun */
+#define ICSR1_CRE (1 << 5) /* CRC error */
+#define ICSR1_EOF (1 << 4) /* End of frame */
+#define ICSR1_TNF (1 << 3) /* Transmit FIFO not full */
+#define ICSR1_RNE (1 << 2) /* Receive FIFO not empty */
+#define ICSR1_TBY (1 << 1) /* Tramsmiter busy flag */
+#define ICSR1_RSY (1 << 0) /* Recevier synchronized flag */
/*
#define RTAR __REG(0x40900004) /* RTC Alarm Register */
#define RTSR __REG(0x40900008) /* RTC Status Register */
#define RTTR __REG(0x4090000C) /* RTC Timer Trim Register */
+#define PIAR __REG(0x40900038) /* Periodic Interrupt Alarm Register */
+#define RTSR_PICE (1 << 15) /* Periodic interrupt count enable */
+#define RTSR_PIALE (1 << 14) /* Periodic interrupt Alarm enable */
#define RTSR_HZE (1 << 3) /* HZ interrupt enable */
#define RTSR_ALE (1 << 2) /* RTC alarm interrupt enable */
#define RTSR_HZ (1 << 1) /* HZ rising-edge detected */
#define OSMR1 __REG(0x40A00004) /* */
#define OSMR2 __REG(0x40A00008) /* */
#define OSMR3 __REG(0x40A0000C) /* */
+#define OSMR4 __REG(0x40A00080) /* */
#define OSCR __REG(0x40A00010) /* OS Timer Counter Register */
+#define OSCR4 __REG(0x40A00040) /* OS Timer Counter Register */
+#define OMCR4 __REG(0x40A000C0) /* */
#define OSSR __REG(0x40A00014) /* OS Timer Status Register */
#define OWER __REG(0x40A00018) /* OS Timer Watchdog Enable Register */
#define OIER __REG(0x40A0001C) /* OS Timer Interrupt Enable Register */
#define GAFR1_L __REG(0x40E0005C) /* GPIO Alternate Function Select Register GPIO<47:32> */
#define GAFR1_U __REG(0x40E00060) /* GPIO Alternate Function Select Register GPIO<63:48> */
#define GAFR2_L __REG(0x40E00064) /* GPIO Alternate Function Select Register GPIO<79:64> */
-#define GAFR2_U __REG(0x40E00068) /* GPIO Alternate Function Select Register GPIO 80 */
+#define GAFR2_U __REG(0x40E00068) /* GPIO Alternate Function Select Register GPIO<95-80> */
+#define GAFR3_L __REG(0x40E0006C) /* GPIO Alternate Function Select Register GPIO<111:96> */
+#define GAFR3_U __REG(0x40E00070) /* GPIO Alternate Function Select Register GPIO<127:112> */
+
+#define GPLR3 __REG(0x40E00100) /* GPIO Pin-Level Register GPIO<127:96> */
+#define GPDR3 __REG(0x40E0010C) /* GPIO Pin Direction Register GPIO<127:96> */
+#define GPSR3 __REG(0x40E00118) /* GPIO Pin Output Set Register GPIO<127:96> */
+#define GPCR3 __REG(0x40E00124) /* GPIO Pin Output Clear Register GPIO<127:96> */
+#define GRER3 __REG(0x40E00130) /* GPIO Rising-Edge Detect Register GPIO<127:96> */
+#define GFER3 __REG(0x40E0013C) /* GPIO Falling-Edge Detect Register GPIO<127:96> */
+#define GEDR3 __REG(0x40E00148) /* GPIO Edge Detect Status Register GPIO<127:96> */
/* More handy macros. The argument is a literal GPIO number. */
#define GPIO_bit(x) (1 << ((x) & 0x1f))
+
+#ifdef CONFIG_PXA27x
+
+/* Interrupt Controller */
+
+#define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */
+#define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */
+#define ICLR2 __REG(0x40D000A4) /* Interrupt Controller Level Register 2 */
+#define ICFP2 __REG(0x40D000A8) /* Interrupt Controller FIQ Pending Register 2 */
+#define ICPR2 __REG(0x40D000AC) /* Interrupt Controller Pending Register 2 */
+
+#define _GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3)
+#define _GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3)
+#define _GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3)
+#define _GPCR(x) __REG2(0x40E00024, ((x) & 0x60) >> 3)
+#define _GRER(x) __REG2(0x40E00030, ((x) & 0x60) >> 3)
+#define _GFER(x) __REG2(0x40E0003C, ((x) & 0x60) >> 3)
+#define _GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3)
+#define _GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2)
+
+#define GPLR(x) (*((((x) & 0x7f) < 96) ? &_GPLR(x) : &GPLR3))
+#define GPDR(x) (*((((x) & 0x7f) < 96) ? &_GPDR(x) : &GPDR3))
+#define GPSR(x) (*((((x) & 0x7f) < 96) ? &_GPSR(x) : &GPSR3))
+#define GPCR(x) (*((((x) & 0x7f) < 96) ? &_GPCR(x) : &GPCR3))
+#define GRER(x) (*((((x) & 0x7f) < 96) ? &_GRER(x) : &GRER3))
+#define GFER(x) (*((((x) & 0x7f) < 96) ? &_GFER(x) : &GFER3))
+#define GEDR(x) (*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3))
+#define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \
+ ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U)))
+#else
+
#define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3)
#define GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3)
#define GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3)
#define GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3)
#define GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2)
+#endif
+
+
/* GPIO alternate function assignments */
#define GPIO1_RST 1 /* reset */
#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */
#define GPIO31_SYNC 31 /* AC97/I2S sync */
#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */
+#define GPIO32_SYSCLK 32 /* I2S System Clock */
+#define GPIO32_MMCCLK 32 /* MMC Clock (PXA270) */
#define GPIO33_nCS_5 33 /* chip select 5 */
#define GPIO34_FFRXD 34 /* FFUART receive */
#define GPIO34_MMCCS0 34 /* MMC Chip Select 0 */
#define GPIO40_FFDTR 40 /* FFUART data terminal Ready */
#define GPIO41_FFRTS 41 /* FFUART request to send */
#define GPIO42_BTRXD 42 /* BTUART receive data */
+#define GPIO42_HWRXD 42 /* HWUART receive data */
#define GPIO43_BTTXD 43 /* BTUART transmit data */
+#define GPIO43_HWTXD 43 /* HWUART transmit data */
#define GPIO44_BTCTS 44 /* BTUART clear to send */
+#define GPIO44_HWCTS 44 /* HWUART clear to send */
#define GPIO45_BTRTS 45 /* BTUART request to send */
+#define GPIO45_HWRTS 45 /* HWUART request to send */
+#define GPIO45_AC97_SYSCLK 45 /* AC97 System Clock */
#define GPIO46_ICPRXD 46 /* ICP receive data */
#define GPIO46_STRXD 46 /* STD_UART receive data */
#define GPIO47_ICPTXD 47 /* ICP transmit data */
#define GPIO53_MMCCLK 53 /* MMC Clock */
#define GPIO54_MMCCLK 54 /* MMC Clock */
#define GPIO54_pSKTSEL 54 /* Socket Select for Card Space */
+#define GPIO54_nPCE_2 54 /* Card Enable for Card Space (PXA27x) */
#define GPIO55_nPREG 55 /* Card Address bit 26 */
#define GPIO56_nPWAIT 56 /* Wait signal for Card Space */
#define GPIO57_nIOIS16 57 /* Bus Width select for I/O Card Space */
#define GPIO78_nCS_2 78 /* chip select 2 */
#define GPIO79_nCS_3 79 /* chip select 3 */
#define GPIO80_nCS_4 80 /* chip select 4 */
+#define GPIO81_NSCLK 81 /* NSSP clock */
+#define GPIO82_NSFRM 82 /* NSSP Frame */
+#define GPIO83_NSTXD 83 /* NSSP transmit */
+#define GPIO84_NSRXD 84 /* NSSP receive */
+#define GPIO85_nPCE_1 85 /* Card Enable for Card Space (PXA27x) */
+#define GPIO92_MMCDAT0 92 /* MMC DAT0 (PXA27x) */
+#define GPIO109_MMCDAT1 109 /* MMC DAT1 (PXA27x) */
+#define GPIO110_MMCDAT2 110 /* MMC DAT2 (PXA27x) */
+#define GPIO110_MMCCS0 110 /* MMC Chip Select 0 (PXA27x) */
+#define GPIO111_MMCDAT3 111 /* MMC DAT3 (PXA27x) */
+#define GPIO111_MMCCS1 111 /* MMC Chip Select 1 (PXA27x) */
+#define GPIO112_MMCCMD 112 /* MMC CMD (PXA27x) */
+#define GPIO113_I2S_SYSCLK 113 /* I2S System Clock (PXA27x) */
+#define GPIO113_AC97_RESET_N 113 /* AC97 NRESET on (PXA27x) */
/* GPIO alternate function mode & direction */
#define GPIO_MD_MASK_NR 0x07f
#define GPIO_MD_MASK_DIR 0x080
#define GPIO_MD_MASK_FN 0x300
+#define GPIO_DFLT_LOW 0x400
+#define GPIO_DFLT_HIGH 0x800
#define GPIO1_RTS_MD ( 1 | GPIO_ALT_FN_1_IN)
#define GPIO6_MMCCLK_MD ( 6 | GPIO_ALT_FN_1_OUT)
#define GPIO18_RDY_MD (18 | GPIO_ALT_FN_1_IN)
#define GPIO19_DREQ1_MD (19 | GPIO_ALT_FN_1_IN)
#define GPIO20_DREQ0_MD (20 | GPIO_ALT_FN_1_IN)
-#define GPIO23_SCLK_md (23 | GPIO_ALT_FN_2_OUT)
+#define GPIO23_SCLK_MD (23 | GPIO_ALT_FN_2_OUT)
#define GPIO24_SFRM_MD (24 | GPIO_ALT_FN_2_OUT)
#define GPIO25_STXD_MD (25 | GPIO_ALT_FN_2_OUT)
#define GPIO26_SRXD_MD (26 | GPIO_ALT_FN_1_IN)
#define GPIO27_SEXTCLK_MD (27 | GPIO_ALT_FN_1_IN)
#define GPIO28_BITCLK_AC97_MD (28 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_I2S_MD (28 | GPIO_ALT_FN_2_IN)
+#define GPIO28_BITCLK_IN_I2S_MD (28 | GPIO_ALT_FN_2_IN)
+#define GPIO28_BITCLK_OUT_I2S_MD (28 | GPIO_ALT_FN_1_OUT)
#define GPIO29_SDATA_IN_AC97_MD (29 | GPIO_ALT_FN_1_IN)
#define GPIO29_SDATA_IN_I2S_MD (29 | GPIO_ALT_FN_2_IN)
#define GPIO30_SDATA_OUT_AC97_MD (30 | GPIO_ALT_FN_2_OUT)
#define GPIO30_SDATA_OUT_I2S_MD (30 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT)
+#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN)
+#define GPIO32_SYSCLK_I2S_MD (32 | GPIO_ALT_FN_1_OUT)
+#define GPIO32_MMCCLK_MD ( 32 | GPIO_ALT_FN_2_OUT)
#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT)
#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN)
#define GPIO34_MMCCS0_MD (34 | GPIO_ALT_FN_2_OUT)
#define GPIO40_FFDTR_MD (40 | GPIO_ALT_FN_2_OUT)
#define GPIO41_FFRTS_MD (41 | GPIO_ALT_FN_2_OUT)
#define GPIO42_BTRXD_MD (42 | GPIO_ALT_FN_1_IN)
+#define GPIO42_HWRXD_MD (42 | GPIO_ALT_FN_3_IN)
#define GPIO43_BTTXD_MD (43 | GPIO_ALT_FN_2_OUT)
+#define GPIO43_HWTXD_MD (43 | GPIO_ALT_FN_3_OUT)
#define GPIO44_BTCTS_MD (44 | GPIO_ALT_FN_1_IN)
+#define GPIO44_HWCTS_MD (44 | GPIO_ALT_FN_3_IN)
#define GPIO45_BTRTS_MD (45 | GPIO_ALT_FN_2_OUT)
+#define GPIO45_HWRTS_MD (45 | GPIO_ALT_FN_3_OUT)
+#define GPIO45_SYSCLK_AC97_MD (45 | GPIO_ALT_FN_1_OUT)
#define GPIO46_ICPRXD_MD (46 | GPIO_ALT_FN_1_IN)
#define GPIO46_STRXD_MD (46 | GPIO_ALT_FN_2_IN)
#define GPIO47_ICPTXD_MD (47 | GPIO_ALT_FN_2_OUT)
#define GPIO47_STTXD_MD (47 | GPIO_ALT_FN_1_OUT)
#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT)
+#define GPIO48_HWTXD_MD (48 | GPIO_ALT_FN_1_OUT)
+#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT)
+#define GPIO49_HWRXD_MD (49 | GPIO_ALT_FN_1_IN)
#define GPIO49_nPWE_MD (49 | GPIO_ALT_FN_2_OUT)
#define GPIO50_nPIOR_MD (50 | GPIO_ALT_FN_2_OUT)
+#define GPIO50_HWCTS_MD (50 | GPIO_ALT_FN_1_IN)
+#define GPIO51_HWRTS_MD (51 | GPIO_ALT_FN_1_OUT)
#define GPIO51_nPIOW_MD (51 | GPIO_ALT_FN_2_OUT)
#define GPIO52_nPCE_1_MD (52 | GPIO_ALT_FN_2_OUT)
#define GPIO53_nPCE_2_MD (53 | GPIO_ALT_FN_2_OUT)
#define GPIO53_MMCCLK_MD (53 | GPIO_ALT_FN_1_OUT)
#define GPIO54_MMCCLK_MD (54 | GPIO_ALT_FN_1_OUT)
+#define GPIO54_nPCE_2_MD (54 | GPIO_ALT_FN_2_OUT)
#define GPIO54_pSKTSEL_MD (54 | GPIO_ALT_FN_2_OUT)
#define GPIO55_nPREG_MD (55 | GPIO_ALT_FN_2_OUT)
#define GPIO56_nPWAIT_MD (56 | GPIO_ALT_FN_1_IN)
#define GPIO77_LCD_ACBIAS_MD (77 | GPIO_ALT_FN_2_OUT)
#define GPIO78_nCS_2_MD (78 | GPIO_ALT_FN_2_OUT)
#define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT)
+#define GPIO79_pSKTSEL_MD (79 | GPIO_ALT_FN_1_OUT)
#define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT)
-
+#define GPIO81_NSSP_CLK_OUT (81 | GPIO_ALT_FN_1_OUT)
+#define GPIO81_NSSP_CLK_IN (81 | GPIO_ALT_FN_1_IN)
+#define GPIO82_NSSP_FRM_OUT (82 | GPIO_ALT_FN_1_OUT)
+#define GPIO82_NSSP_FRM_IN (82 | GPIO_ALT_FN_1_IN)
+#define GPIO83_NSSP_TX (83 | GPIO_ALT_FN_1_OUT)
+#define GPIO83_NSSP_RX (83 | GPIO_ALT_FN_2_IN)
+#define GPIO84_NSSP_TX (84 | GPIO_ALT_FN_1_OUT)
+#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN)
+#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT)
+#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT)
+#define GPIO104_pSKTSEL_MD (104 | GPIO_ALT_FN_1_OUT)
+#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT)
+#define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT)
+#define GPIO110_MMCCS0_MD (110 | GPIO_ALT_FN_1_OUT)
+#define GPIO111_MMCDAT3_MD (111 | GPIO_ALT_FN_1_OUT)
+#define GPIO110_MMCCS1_MD (111 | GPIO_ALT_FN_1_OUT)
+#define GPIO112_MMCCMD_MD (112 | GPIO_ALT_FN_1_OUT)
+#define GPIO113_I2S_SYSCLK_MD (113 | GPIO_ALT_FN_1_OUT)
+#define GPIO113_AC97_RESET_N_MD (113 | GPIO_ALT_FN_2_OUT)
+#define GPIO117_I2CSCL_MD (117 | GPIO_ALT_FN_1_OUT)
+#define GPIO118_I2CSDA_MD (118 | GPIO_ALT_FN_1_IN)
/*
* Power Manager
#define PGSR0 __REG(0x40F00020) /* Power Manager GPIO Sleep State Register for GP[31-0] */
#define PGSR1 __REG(0x40F00024) /* Power Manager GPIO Sleep State Register for GP[63-32] */
#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */
+#define PGSR3 __REG(0x40F0002C) /* Power Manager GPIO Sleep State Register for GP[118-96] */
#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */
+#define PSLR __REG(0x40F00034) /* Power Manager Sleep Config Register */
+#define PSTR __REG(0x40F00038) /*Power Manager Standby Config Register */
+#define PSNR __REG(0x40F0003C) /*Power Manager Sense Config Register */
+#define PVCR __REG(0x40F00040) /*Power Manager VoltageControl Register */
+#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-up Enable Reg */
+#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Register */
+#define PCMD(x) __REG2(0x40F00080, (x)<<2)
+#define PCMD0 __REG(0x40F00080 + 0 * 4)
+#define PCMD1 __REG(0x40F00080 + 1 * 4)
+#define PCMD2 __REG(0x40F00080 + 2 * 4)
+#define PCMD3 __REG(0x40F00080 + 3 * 4)
+#define PCMD4 __REG(0x40F00080 + 4 * 4)
+#define PCMD5 __REG(0x40F00080 + 5 * 4)
+#define PCMD6 __REG(0x40F00080 + 6 * 4)
+#define PCMD7 __REG(0x40F00080 + 7 * 4)
+#define PCMD8 __REG(0x40F00080 + 8 * 4)
+#define PCMD9 __REG(0x40F00080 + 9 * 4)
+#define PCMD10 __REG(0x40F00080 + 10 * 4)
+#define PCMD11 __REG(0x40F00080 + 11 * 4)
+#define PCMD12 __REG(0x40F00080 + 12 * 4)
+#define PCMD13 __REG(0x40F00080 + 13 * 4)
+#define PCMD14 __REG(0x40F00080 + 14 * 4)
+#define PCMD15 __REG(0x40F00080 + 15 * 4)
+#define PCMD16 __REG(0x40F00080 + 16 * 4)
+#define PCMD17 __REG(0x40F00080 + 17 * 4)
+#define PCMD18 __REG(0x40F00080 + 18 * 4)
+#define PCMD19 __REG(0x40F00080 + 19 * 4)
+#define PCMD20 __REG(0x40F00080 + 20 * 4)
+#define PCMD21 __REG(0x40F00080 + 21 * 4)
+#define PCMD22 __REG(0x40F00080 + 22 * 4)
+#define PCMD23 __REG(0x40F00080 + 23 * 4)
+#define PCMD24 __REG(0x40F00080 + 24 * 4)
+#define PCMD25 __REG(0x40F00080 + 25 * 4)
+#define PCMD26 __REG(0x40F00080 + 26 * 4)
+#define PCMD27 __REG(0x40F00080 + 27 * 4)
+#define PCMD28 __REG(0x40F00080 + 28 * 4)
+#define PCMD29 __REG(0x40F00080 + 29 * 4)
+#define PCMD30 __REG(0x40F00080 + 30 * 4)
+#define PCMD31 __REG(0x40F00080 + 31 * 4)
+
+#define PCMD_MBC (1<<12)
+#define PCMD_DCE (1<<11)
+#define PCMD_LC (1<<10)
+/* FIXME: PCMD_SQC need be checked. */
+#define PCMD_SQC (3<<8) /* currently only bit 8 is changeable,
+ bit 9 should be 0 all day. */
+#define PVCR_VCSA (0x1<<14)
+#define PVCR_CommandDelay (0xf80)
+#define PCFR_PI2C_EN (0x1 << 6)
+
+#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */
#define PSSR_RDH (1 << 5) /* Read Disable Hold */
#define PSSR_PH (1 << 4) /* Peripheral Control Hold */
+#define PSSR_STS (1 << 3) /* Standby Mode Status */
#define PSSR_VFS (1 << 2) /* VDD Fault Status */
#define PSSR_BFS (1 << 1) /* Battery Fault Status */
#define PSSR_SSS (1 << 0) /* Software Sleep Status */
+#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */
+
+#define PCFR_RO (1 << 15) /* RDH Override */
+#define PCFR_PO (1 << 14) /* PH Override */
+#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */
+#define PCFR_L1_EN (1 << 11) /* Sleep Mode L1 converter Enable */
+#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */
+#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */
+#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */
+#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */
#define PCFR_DS (1 << 3) /* Deep Sleep Mode */
#define PCFR_FS (1 << 2) /* Float Static Chip Selects */
#define PCFR_FP (1 << 1) /* Float PCMCIA controls */
#define RCSR_WDR (1 << 1) /* Watchdog Reset */
#define RCSR_HWR (1 << 0) /* Hardware Reset */
+#define PWER_GPIO(Nb) (1 << Nb) /* GPIO [0..15] wake-up enable */
+#define PWER_GPIO0 PWER_GPIO (0) /* GPIO [0] wake-up enable */
+#define PWER_GPIO1 PWER_GPIO (1) /* GPIO [1] wake-up enable */
+#define PWER_GPIO2 PWER_GPIO (2) /* GPIO [2] wake-up enable */
+#define PWER_GPIO3 PWER_GPIO (3) /* GPIO [3] wake-up enable */
+#define PWER_GPIO4 PWER_GPIO (4) /* GPIO [4] wake-up enable */
+#define PWER_GPIO5 PWER_GPIO (5) /* GPIO [5] wake-up enable */
+#define PWER_GPIO6 PWER_GPIO (6) /* GPIO [6] wake-up enable */
+#define PWER_GPIO7 PWER_GPIO (7) /* GPIO [7] wake-up enable */
+#define PWER_GPIO8 PWER_GPIO (8) /* GPIO [8] wake-up enable */
+#define PWER_GPIO9 PWER_GPIO (9) /* GPIO [9] wake-up enable */
+#define PWER_GPIO10 PWER_GPIO (10) /* GPIO [10] wake-up enable */
+#define PWER_GPIO11 PWER_GPIO (11) /* GPIO [11] wake-up enable */
+#define PWER_GPIO12 PWER_GPIO (12) /* GPIO [12] wake-up enable */
+#define PWER_GPIO13 PWER_GPIO (13) /* GPIO [13] wake-up enable */
+#define PWER_GPIO14 PWER_GPIO (14) /* GPIO [14] wake-up enable */
+#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */
+#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */
+
/*
* SSP Serial Port Registers
+ * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
+ * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
*/
-#define SSCR0 __REG(0x41000000) /* SSP Control Register 0 */
-#define SSCR1 __REG(0x41000004) /* SSP Control Register 1 */
-#define SSSR __REG(0x41000008) /* SSP Status Register */
-#define SSITR __REG(0x4100000C) /* SSP Interrupt Test Register */
-#define SSDR __REG(0x41000010) /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
+ /* Common PXA2xx bits first */
#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
#define SSCR0_National (0x2 << 4) /* National Microwire */
#define SSCR0_ECS (1 << 6) /* External clock select */
#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
+#if defined(CONFIG_PXA25x)
#define SSCR0_SCR (0x0000ff00) /* Serial Clock Rate (mask) */
#define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */
+#elif defined(CONFIG_PXA27x)
+#define SSCR0_SCR (0x000fff00) /* Serial Clock Rate (mask) */
+#define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */
+#define SSCR0_EDSS (1 << 20) /* Extended data size select */
+#define SSCR0_NCS (1 << 21) /* Network clock select */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */
+#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */
+#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */
+#define SSCR0_SlotsPerFrm(c) ((x) - 1) /* Time slots per frame [1..8] */
+#define SSCR0_ADC (1 << 30) /* Audio clock select */
+#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */
+#endif
#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
+#define SSCR0_TIM (1 << 23) /* Transmit FIFO Under Run Interrupt Mask */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO Over Run interrupt Mask */
+#define SSCR0_NCS (1 << 21) /* Network Clock Select */
+#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */
+
+/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
+#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
+#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
+#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
+#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
+#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
+#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
+#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
+#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
+#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
+#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
+#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
+#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
+#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
+#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
+#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */
+#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
+#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
+
+#define SSSR_BCE (1 << 23) /* Bit Count Error */
+#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
+#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
+#define SSSR_EOC (1 << 20) /* End Of Chain */
+#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
+#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
+
+#define SSPSP_DMYSTOP(x) (x << 23) /* Dummy Stop */
+#define SSPSP_SFRMWDTH(x) (x << 16) /* Serial Frame Width */
+#define SSPSP_SFRMDLY(x) (x << 9) /* Serial Frame Delay */
+#define SSPSP_DMYSTRT(x) (x << 7) /* Dummy Start */
+#define SSPSP_STRTDLY(x) (x << 4) /* Start Delay */
+#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
+#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
+#define SSPSP_SCMODE(x) (x << 0) /* Serial Bit Rate Clock Mode */
+
+
+#define SSCR0_P1 __REG(0x41000000) /* SSP Port 1 Control Register 0 */
+#define SSCR1_P1 __REG(0x41000004) /* SSP Port 1 Control Register 1 */
+#define SSSR_P1 __REG(0x41000008) /* SSP Port 1 Status Register */
+#define SSITR_P1 __REG(0x4100000C) /* SSP Port 1 Interrupt Test Register */
+#define SSDR_P1 __REG(0x41000010) /* (Write / Read) SSP Port 1 Data Write Register/SSP Data Read Register */
+
+/* Support existing PXA25x drivers */
+#define SSCR0 SSCR0_P1 /* SSP Control Register 0 */
+#define SSCR1 SSCR1_P1 /* SSP Control Register 1 */
+#define SSSR SSSR_P1 /* SSP Status Register */
+#define SSITR SSITR_P1 /* SSP Interrupt Test Register */
+#define SSDR SSDR_P1 /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
+
+/* PXA27x ports */
+#if defined (CONFIG_PXA27x)
+#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
+#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
+#define SSCR0_P2 __REG(0x41700000) /* SSP Port 2 Control Register 0 */
+#define SSCR1_P2 __REG(0x41700004) /* SSP Port 2 Control Register 1 */
+#define SSSR_P2 __REG(0x41700008) /* SSP Port 2 Status Register */
+#define SSITR_P2 __REG(0x4170000C) /* SSP Port 2 Interrupt Test Register */
+#define SSDR_P2 __REG(0x41700010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
+#define SSTO_P2 __REG(0x41700028) /* SSP Port 2 Time Out Register */
+#define SSPSP_P2 __REG(0x4170002C) /* SSP Port 2 Programmable Serial Protocol */
+#define SSCR0_P3 __REG(0x41900000) /* SSP Port 3 Control Register 0 */
+#define SSCR1_P3 __REG(0x41900004) /* SSP Port 3 Control Register 1 */
+#define SSSR_P3 __REG(0x41900008) /* SSP Port 3 Status Register */
+#define SSITR_P3 __REG(0x4190000C) /* SSP Port 3 Interrupt Test Register */
+#define SSDR_P3 __REG(0x41900010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
+#define SSTO_P3 __REG(0x41900028) /* SSP Port 3 Time Out Register */
+#define SSPSP_P3 __REG(0x4190002C) /* SSP Port 3 Programmable Serial Protocol */
+#else /* PXA255 (only port 2) and PXA26x ports*/
+#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
+#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
+#define SSCR0_P2 __REG(0x41400000) /* SSP Port 2 Control Register 0 */
+#define SSCR1_P2 __REG(0x41400004) /* SSP Port 2 Control Register 1 */
+#define SSSR_P2 __REG(0x41400008) /* SSP Port 2 Status Register */
+#define SSITR_P2 __REG(0x4140000C) /* SSP Port 2 Interrupt Test Register */
+#define SSDR_P2 __REG(0x41400010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
+#define SSTO_P2 __REG(0x41400028) /* SSP Port 2 Time Out Register */
+#define SSPSP_P2 __REG(0x4140002C) /* SSP Port 2 Programmable Serial Protocol */
+#define SSCR0_P3 __REG(0x41500000) /* SSP Port 3 Control Register 0 */
+#define SSCR1_P3 __REG(0x41500004) /* SSP Port 3 Control Register 1 */
+#define SSSR_P3 __REG(0x41500008) /* SSP Port 3 Status Register */
+#define SSITR_P3 __REG(0x4150000C) /* SSP Port 3 Interrupt Test Register */
+#define SSDR_P3 __REG(0x41500010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
+#define SSTO_P3 __REG(0x41500028) /* SSP Port 3 Time Out Register */
+#define SSPSP_P3 __REG(0x4150002C) /* SSP Port 3 Programmable Serial Protocol */
+#endif
+
+#define SSCR0_P(x) (*(((x) == 1) ? &SSCR0_P1 : ((x) == 2) ? &SSCR0_P2 : ((x) == 3) ? &SSCR0_P3 : NULL))
+#define SSCR1_P(x) (*(((x) == 1) ? &SSCR1_P1 : ((x) == 2) ? &SSCR1_P2 : ((x) == 3) ? &SSCR1_P3 : NULL))
+#define SSSR_P(x) (*(((x) == 1) ? &SSSR_P1 : ((x) == 2) ? &SSSR_P2 : ((x) == 3) ? &SSSR_P3 : NULL))
+#define SSITR_P(x) (*(((x) == 1) ? &SSITR_P1 : ((x) == 2) ? &SSITR_P2 : ((x) == 3) ? &SSITR_P3 : NULL))
+#define SSDR_P(x) (*(((x) == 1) ? &SSDR_P1 : ((x) == 2) ? &SSDR_P2 : ((x) == 3) ? &SSDR_P3 : NULL))
+#define SSTO_P(x) (*(((x) == 1) ? &SSTO_P1 : ((x) == 2) ? &SSTO_P2 : ((x) == 3) ? &SSTO_P3 : NULL))
+#define SSPSP_P(x) (*(((x) == 1) ? &SSPSP_P1 : ((x) == 2) ? &SSPSP_P2 : ((x) == 3) ? &SSPSP_P3 : NULL))
/*
* MultiMediaCard (MMC) controller
#define CCCR __REG(0x41300000) /* Core Clock Configuration Register */
#define CKEN __REG(0x41300004) /* Clock Enable Register */
#define OSCC __REG(0x41300008) /* Oscillator Configuration Register */
+#define CCSR __REG(0x4130000C) /* Core Clock Status Register */
#define CCCR_N_MASK 0x0380 /* Run Mode Frequency to Turbo Mode Frequency Multiplier */
#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */
#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */
+#define CKEN24_CAMERA (1 << 24) /* Camera Interface Clock Enable */
+#define CKEN23_SSP1 (1 << 23) /* SSP1 Unit Clock Enable */
+#define CKEN22_MEMC (1 << 22) /* Memory Controller Clock Enable */
+#define CKEN21_MEMSTK (1 << 21) /* Memory Stick Host Controller */
+#define CKEN20_IM (1 << 20) /* Internal Memory Clock Enable */
+#define CKEN19_KEYPAD (1 << 19) /* Keypad Interface Clock Enable */
+#define CKEN18_USIM (1 << 18) /* USIM Unit Clock Enable */
+#define CKEN17_MSL (1 << 17) /* MSL Unit Clock Enable */
#define CKEN16_LCD (1 << 16) /* LCD Unit Clock Enable */
+#define CKEN15_PWRI2C (1 << 15) /* PWR I2C Unit Clock Enable */
#define CKEN14_I2C (1 << 14) /* I2C Unit Clock Enable */
#define CKEN13_FICP (1 << 13) /* FICP Unit Clock Enable */
#define CKEN12_MMC (1 << 12) /* MMC Unit Clock Enable */
#define CKEN11_USB (1 << 11) /* USB Unit Clock Enable */
+#define CKEN10_ASSP (1 << 10) /* ASSP (SSP3) Clock Enable */
+#define CKEN10_USBHOST (1 << 10) /* USB Host Unit Clock Enable */
+#define CKEN9_OSTIMER (1 << 9) /* OS Timer Unit Clock Enable */
+#define CKEN9_NSSP (1 << 9) /* NSSP (SSP2) Clock Enable */
#define CKEN8_I2S (1 << 8) /* I2S Unit Clock Enable */
#define CKEN7_BTUART (1 << 7) /* BTUART Unit Clock Enable */
#define CKEN6_FFUART (1 << 6) /* FFUART Unit Clock Enable */
#define CKEN5_STUART (1 << 5) /* STUART Unit Clock Enable */
+#define CKEN4_HWUART (1 << 4) /* HWUART Unit Clock Enable */
+#define CKEN4_SSP3 (1 << 4) /* SSP3 Unit Clock Enable */
#define CKEN3_SSP (1 << 3) /* SSP Unit Clock Enable */
+#define CKEN3_SSP2 (1 << 3) /* SSP2 Unit Clock Enable */
#define CKEN2_AC97 (1 << 2) /* AC97 Unit Clock Enable */
#define CKEN1_PWM1 (1 << 1) /* PWM1 Clock Enable */
#define CKEN0_PWM0 (1 << 0) /* PWM0 Clock Enable */
#define TMEDRGBR __REG(0x44000040) /* TMED RGB Seed Register */
#define TMEDCR __REG(0x44000044) /* TMED Control Register */
+#define LCCR3_1BPP (0 << 24)
+#define LCCR3_2BPP (1 << 24)
+#define LCCR3_4BPP (2 << 24)
+#define LCCR3_8BPP (3 << 24)
+#define LCCR3_16BPP (4 << 24)
+
#define FDADR0 __REG(0x44000200) /* DMA Channel 0 Frame Descriptor Address Register */
#define FSADR0 __REG(0x44000204) /* DMA Channel 0 Frame Source Address Register */
#define FIDR0 __REG(0x44000208) /* DMA Channel 0 Frame ID Register */
#define LDCMD1 __REG(0x4400021C) /* DMA Channel 1 Command Register */
#define LCCR0_ENB (1 << 0) /* LCD Controller enable */
-#define LCCR0_CMS (1 << 1) /* Color = 0, Monochrome = 1 */
-#define LCCR0_SDS (1 << 2) /* Single Panel = 0, Dual Panel = 1 */
+#define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */
+#define LCCR0_Color (LCCR0_CMS*0) /* Color display */
+#define LCCR0_Mono (LCCR0_CMS*1) /* Monochrome display */
+#define LCCR0_SDS (1 << 2) /* Single/Dual Panel Display */
+ /* Select */
+#define LCCR0_Sngl (LCCR0_SDS*0) /* Single panel display */
+#define LCCR0_Dual (LCCR0_SDS*1) /* Dual panel display */
+
#define LCCR0_LDM (1 << 3) /* LCD Disable Done Mask */
#define LCCR0_SFM (1 << 4) /* Start of frame mask */
#define LCCR0_IUM (1 << 5) /* Input FIFO underrun mask */
#define LCCR0_EFM (1 << 6) /* End of Frame mask */
-#define LCCR0_PAS (1 << 7) /* Passive = 0, Active = 1 */
-#define LCCR0_BLE (1 << 8) /* Little Endian = 0, Big Endian = 1 */
-#define LCCR0_DPD (1 << 9) /* Double Pixel mode, 4 pixel value = 0, 8 pixle values = 1 */
+#define LCCR0_PAS (1 << 7) /* Passive/Active display Select */
+#define LCCR0_Pas (LCCR0_PAS*0) /* Passive display (STN) */
+#define LCCR0_Act (LCCR0_PAS*1) /* Active display (TFT) */
+#define LCCR0_DPD (1 << 9) /* Double Pixel Data (monochrome */
+ /* display mode) */
+#define LCCR0_4PixMono (LCCR0_DPD*0) /* 4-Pixel/clock Monochrome */
+ /* display */
+#define LCCR0_8PixMono (LCCR0_DPD*1) /* 8-Pixel/clock Monochrome */
+ /* display */
#define LCCR0_DIS (1 << 10) /* LCD Disable */
#define LCCR0_QDM (1 << 11) /* LCD Quick Disable mask */
#define LCCR0_PDD (0xff << 12) /* Palette DMA request delay */
#define LCCR0_PDD_S 12
#define LCCR0_BM (1 << 20) /* Branch mask */
#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */
+#define LCCR0_LCDT (1 << 22) /* LCD panel type */
+#define LCCR0_RDSTM (1 << 23) /* Read status interrupt mask */
+#define LCCR0_CMDIM (1 << 24) /* Command interrupt mask */
+#define LCCR0_OUC (1 << 25) /* Overlay Underlay control bit */
+#define LCCR0_LDDALT (1 << 26) /* LDD alternate mapping control */
#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */
#define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \
#define LCCR3_API_S 16
#define LCCR3_VSP (1 << 20) /* vertical sync polarity */
#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */
-#define LCCR3_PCP (1 << 22) /* pixel clock polarity */
-#define LCCR3_OEP (1 << 23) /* output enable polarity */
+#define LCCR3_PCP (1 << 22) /* Pixel Clock Polarity (L_PCLK) */
+#define LCCR3_PixRsEdg (LCCR3_PCP*0) /* Pixel clock Rising-Edge */
+#define LCCR3_PixFlEdg (LCCR3_PCP*1) /* Pixel clock Falling-Edge */
+
+#define LCCR3_OEP (1 << 23) /* Output Enable Polarity (L_BIAS, */
+ /* active display mode) */
+#define LCCR3_OutEnH (LCCR3_OEP*0) /* Output Enable active High */
+#define LCCR3_OutEnL (LCCR3_OEP*1) /* Output Enable active Low */
+
#if 0
#define LCCR3_BPP (7 << 24) /* bits per pixel */
#define LCCR3_BPP_S 24
#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
+/*
+ * More handy macros for PCMCIA
+ *
+ * Arg is socket number
+ */
+#define MCMEM(s) __REG2(0x48000028, (s)<<2 ) /* Card interface Common Memory Space Socket s Timing */
+#define MCATT(s) __REG2(0x48000030, (s)<<2 ) /* Card interface Attribute Space Socket s Timing Configuration */
+#define MCIO(s) __REG2(0x48000038, (s)<<2 ) /* Card interface I/O Space Socket s Timing Configuration */
+
+/* MECR register defines */
+#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */
+#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */
+
+#define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */
#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */
#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */
#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */
#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */
+#ifdef CONFIG_PXA27x
+
+#define ARB_CNTRL __REG(0x48000048) /* Arbiter Control Register */
+#define ARB_DMA_SLV_PARK (1<<31) /* Be parked with DMA slave when idle */
+#define ARB_CI_PARK (1<<30) /* Be parked with Camera Interface when idle */
+#define ARB_EX_MEM_PARK (1<<29) /* Be parked with external MEMC when idle */
+#define ARB_INT_MEM_PARK (1<<28) /* Be parked with internal MEMC when idle */
+#define ARB_USB_PARK (1<<27) /* Be parked with USB when idle */
+#define ARB_LCD_PARK (1<<26) /* Be parked with LCD when idle */
+#define ARB_DMA_PARK (1<<25) /* Be parked with DMA when idle */
+#define ARB_CORE_PARK (1<<24) /* Be parked with core when idle */
+#define ARB_LOCK_FLAG (1<<23) /* Only Locking masters gain access to the bus */
+
+/*
+ * Keypad
+ */
+#define KPC __REG(0x41500000) /* Keypad Interface Control register */
+#define KPDK __REG(0x41500008) /* Keypad Interface Direct Key register */
+#define KPREC __REG(0x41500010) /* Keypad Interface Rotary Encoder register */
+#define KPMK __REG(0x41500018) /* Keypad Interface Matrix Key register */
+#define KPAS __REG(0x41500020) /* Keypad Interface Automatic Scan register */
+#define KPASMKP0 __REG(0x41500028) /* Keypad Interface Automatic Scan Multiple Key Presser register 0 */
+#define KPASMKP1 __REG(0x41500030) /* Keypad Interface Automatic Scan Multiple Key Presser register 1 */
+#define KPASMKP2 __REG(0x41500038) /* Keypad Interface Automatic Scan Multiple Key Presser register 2 */
+#define KPASMKP3 __REG(0x41500040) /* Keypad Interface Automatic Scan Multiple Key Presser register 3 */
+#define KPKDI __REG(0x41500048) /* Keypad Interface Key Debounce Interval register */
+
+#define KPC_AS (0x1 << 30) /* Automatic Scan bit */
+#define KPC_ASACT (0x1 << 29) /* Automatic Scan on Activity */
+#define KPC_MI (0x1 << 22) /* Matrix interrupt bit */
+#define KPC_IMKP (0x1 << 21) /* Ignore Multiple Key Press */
+#define KPC_MS7 (0x1 << 20) /* Matrix scan line 7 */
+#define KPC_MS6 (0x1 << 19) /* Matrix scan line 6 */
+#define KPC_MS5 (0x1 << 18) /* Matrix scan line 5 */
+#define KPC_MS4 (0x1 << 17) /* Matrix scan line 4 */
+#define KPC_MS3 (0x1 << 16) /* Matrix scan line 3 */
+#define KPC_MS2 (0x1 << 15) /* Matrix scan line 2 */
+#define KPC_MS1 (0x1 << 14) /* Matrix scan line 1 */
+#define KPC_MS0 (0x1 << 13) /* Matrix scan line 0 */
+#define KPC_MS_ALL (KPC_MS0 | KPC_MS1 | KPC_MS2 | KPC_MS3 | KPC_MS4 | KPC_MS5 | KPC_MS6 | KPC_MS7)
+#define KPC_ME (0x1 << 12) /* Matrix Keypad Enable */
+#define KPC_MIE (0x1 << 11) /* Matrix Interrupt Enable */
+#define KPC_DK_DEB_SEL (0x1 << 9) /* Direct Keypad Debounce Select */
+#define KPC_DI (0x1 << 5) /* Direct key interrupt bit */
+#define KPC_RE_ZERO_DEB (0x1 << 4) /* Rotary Encoder Zero Debounce */
+#define KPC_REE1 (0x1 << 3) /* Rotary Encoder1 Enable */
+#define KPC_REE0 (0x1 << 2) /* Rotary Encoder0 Enable */
+#define KPC_DE (0x1 << 1) /* Direct Keypad Enable */
+#define KPC_DIE (0x1 << 0) /* Direct Keypad interrupt Enable */
+
+#define KPDK_DKP (0x1 << 31)
+#define KPDK_DK7 (0x1 << 7)
+#define KPDK_DK6 (0x1 << 6)
+#define KPDK_DK5 (0x1 << 5)
+#define KPDK_DK4 (0x1 << 4)
+#define KPDK_DK3 (0x1 << 3)
+#define KPDK_DK2 (0x1 << 2)
+#define KPDK_DK1 (0x1 << 1)
+#define KPDK_DK0 (0x1 << 0)
+
+#define KPREC_OF1 (0x1 << 31)
+#define kPREC_UF1 (0x1 << 30)
+#define KPREC_OF0 (0x1 << 15)
+#define KPREC_UF0 (0x1 << 14)
+
+#define KPMK_MKP (0x1 << 31)
+#define KPAS_SO (0x1 << 31)
+#define KPASMKPx_SO (0x1 << 31)
+
+/*
+ * UHC: USB Host Controller (OHCI-like) register definitions
+ */
+#define UHC_BASE_PHYS (0x4C000000)
+#define UHCREV __REG(0x4C000000) /* UHC HCI Spec Revision */
+#define UHCHCON __REG(0x4C000004) /* UHC Host Control Register */
+#define UHCCOMS __REG(0x4C000008) /* UHC Command Status Register */
+#define UHCINTS __REG(0x4C00000C) /* UHC Interrupt Status Register */
+#define UHCINTE __REG(0x4C000010) /* UHC Interrupt Enable */
+#define UHCINTD __REG(0x4C000014) /* UHC Interrupt Disable */
+#define UHCHCCA __REG(0x4C000018) /* UHC Host Controller Comm. Area */
+#define UHCPCED __REG(0x4C00001C) /* UHC Period Current Endpt Descr */
+#define UHCCHED __REG(0x4C000020) /* UHC Control Head Endpt Descr */
+#define UHCCCED __REG(0x4C000024) /* UHC Control Current Endpt Descr */
+#define UHCBHED __REG(0x4C000028) /* UHC Bulk Head Endpt Descr */
+#define UHCBCED __REG(0x4C00002C) /* UHC Bulk Current Endpt Descr */
+#define UHCDHEAD __REG(0x4C000030) /* UHC Done Head */
+#define UHCFMI __REG(0x4C000034) /* UHC Frame Interval */
+#define UHCFMR __REG(0x4C000038) /* UHC Frame Remaining */
+#define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */
+#define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */
+#define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */
+
+#define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */
+#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
+
+#define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
+#define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */
+#define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */
+#define UHCRHPS2 __REG(0x4C000058) /* UHC Root Hub Port 2 Status */
+#define UHCRHPS3 __REG(0x4C00005C) /* UHC Root Hub Port 3 Status */
+
+#define UHCSTAT __REG(0x4C000060) /* UHC Status Register */
+#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
+#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
+#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
+#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
+#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
+#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
+#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
+#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
+#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
+
+#define UHCHR __REG(0x4C000064) /* UHC Reset Register */
+#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
+#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
+#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
+#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
+#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
+#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
+#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
+#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
+#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
+#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
+#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
+
+#define UHCHIE __REG(0x4C000068) /* UHC Interrupt Enable Register*/
+#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
+#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
+#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
+#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
+#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
+ Interrupt Enable*/
+#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
+#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
+
+#define UHCHIT __REG(0x4C00006C) /* UHC Interrupt Test register */
+
+/* Camera Interface */
+#define CICR0 __REG(0x50000000)
+#define CICR1 __REG(0x50000004)
+#define CICR2 __REG(0x50000008)
+#define CICR3 __REG(0x5000000C)
+#define CICR4 __REG(0x50000010)
+#define CISR __REG(0x50000014)
+#define CIFR __REG(0x50000018)
+#define CITOR __REG(0x5000001C)
+#define CIBR0 __REG(0x50000028)
+#define CIBR1 __REG(0x50000030)
+#define CIBR2 __REG(0x50000038)
+
+#define CICR0_DMAEN (1 << 31) /* DMA request enable */
+#define CICR0_PAR_EN (1 << 30) /* Parity enable */
+#define CICR0_SL_CAP_EN (1 << 29) /* Capture enable for slave mode */
+#define CICR0_ENB (1 << 28) /* Camera interface enable */
+#define CICR0_DIS (1 << 27) /* Camera interface disable */
+#define CICR0_SIM (0x7 << 24) /* Sensor interface mode mask */
+#define CICR0_TOM (1 << 9) /* Time-out mask */
+#define CICR0_RDAVM (1 << 8) /* Receive-data-available mask */
+#define CICR0_FEM (1 << 7) /* FIFO-empty mask */
+#define CICR0_EOLM (1 << 6) /* End-of-line mask */
+#define CICR0_PERRM (1 << 5) /* Parity-error mask */
+#define CICR0_QDM (1 << 4) /* Quick-disable mask */
+#define CICR0_CDM (1 << 3) /* Disable-done mask */
+#define CICR0_SOFM (1 << 2) /* Start-of-frame mask */
+#define CICR0_EOFM (1 << 1) /* End-of-frame mask */
+#define CICR0_FOM (1 << 0) /* FIFO-overrun mask */
+
+#define CICR1_TBIT (1 << 31) /* Transparency bit */
+#define CICR1_RGBT_CONV (0x3 << 30) /* RGBT conversion mask */
+#define CICR1_PPL (0x3f << 15) /* Pixels per line mask */
+#define CICR1_RGB_CONV (0x7 << 12) /* RGB conversion mask */
+#define CICR1_RGB_F (1 << 11) /* RGB format */
+#define CICR1_YCBCR_F (1 << 10) /* YCbCr format */
+#define CICR1_RGB_BPP (0x7 << 7) /* RGB bis per pixel mask */
+#define CICR1_RAW_BPP (0x3 << 5) /* Raw bis per pixel mask */
+#define CICR1_COLOR_SP (0x3 << 3) /* Color space mask */
+#define CICR1_DW (0x7 << 0) /* Data width mask */
+
+#define CICR2_BLW (0xff << 24) /* Beginning-of-line pixel clock
+ wait count mask */
+#define CICR2_ELW (0xff << 16) /* End-of-line pixel clock
+ wait count mask */
+#define CICR2_HSW (0x3f << 10) /* Horizontal sync pulse width mask */
+#define CICR2_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock
+ wait count mask */
+#define CICR2_FSW (0x7 << 0) /* Frame stabilization
+ wait count mask */
+
+#define CICR3_BFW (0xff << 24) /* Beginning-of-frame line clock
+ wait count mask */
+#define CICR3_EFW (0xff << 16) /* End-of-frame line clock
+ wait count mask */
+#define CICR3_VSW (0x3f << 10) /* Vertical sync pulse width mask */
+#define CICR3_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock
+ wait count mask */
+#define CICR3_LPF (0x3ff << 0) /* Lines per frame mask */
+
+#define CICR4_MCLK_DLY (0x3 << 24) /* MCLK Data Capture Delay mask */
+#define CICR4_PCLK_EN (1 << 23) /* Pixel clock enable */
+#define CICR4_PCP (1 << 22) /* Pixel clock polarity */
+#define CICR4_HSP (1 << 21) /* Horizontal sync polarity */
+#define CICR4_VSP (1 << 20) /* Vertical sync polarity */
+#define CICR4_MCLK_EN (1 << 19) /* MCLK enable */
+#define CICR4_FR_RATE (0x7 << 8) /* Frame rate mask */
+#define CICR4_DIV (0xff << 0) /* Clock divisor mask */
+
+#define CISR_FTO (1 << 15) /* FIFO time-out */
+#define CISR_RDAV_2 (1 << 14) /* Channel 2 receive data available */
+#define CISR_RDAV_1 (1 << 13) /* Channel 1 receive data available */
+#define CISR_RDAV_0 (1 << 12) /* Channel 0 receive data available */
+#define CISR_FEMPTY_2 (1 << 11) /* Channel 2 FIFO empty */
+#define CISR_FEMPTY_1 (1 << 10) /* Channel 1 FIFO empty */
+#define CISR_FEMPTY_0 (1 << 9) /* Channel 0 FIFO empty */
+#define CISR_EOL (1 << 8) /* End of line */
+#define CISR_PAR_ERR (1 << 7) /* Parity error */
+#define CISR_CQD (1 << 6) /* Camera interface quick disable */
+#define CISR_SOF (1 << 5) /* Start of frame */
+#define CISR_CDD (1 << 4) /* Camera interface disable done */
+#define CISR_EOF (1 << 3) /* End of frame */
+#define CISR_IFO_2 (1 << 2) /* FIFO overrun for Channel 2 */
+#define CISR_IFO_1 (1 << 1) /* FIFO overrun for Channel 1 */
+#define CISR_IFO_0 (1 << 0) /* FIFO overrun for Channel 0 */
+
+#define CIFR_FLVL2 (0x7f << 23) /* FIFO 2 level mask */
+#define CIFR_FLVL1 (0x7f << 16) /* FIFO 1 level mask */
+#define CIFR_FLVL0 (0xff << 8) /* FIFO 0 level mask */
+#define CIFR_THL_0 (0x3 << 4) /* Threshold Level for Channel 0 FIFO */
+#define CIFR_RESET_F (1 << 3) /* Reset input FIFOs */
+#define CIFR_FEN2 (1 << 2) /* FIFO enable for channel 2 */
+#define CIFR_FEN1 (1 << 1) /* FIFO enable for channel 1 */
+#define CIFR_FEN0 (1 << 0) /* FIFO enable for channel 0 */
+
+#define SRAM_SIZE 0x40000 /* 4x64K */
+
+#define SRAM_MEM_PHYS 0x5C000000
+
+#define IMPMCR __REG(0x58000000) /* IM Power Management Control Reg */
+#define IMPMSR __REG(0x58000008) /* IM Power Management Status Reg */
+
+#define IMPMCR_PC3 (0x3 << 22) /* Bank 3 Power Control */
+#define IMPMCR_PC3_RUN_MODE (0x0 << 22) /* Run mode */
+#define IMPMCR_PC3_STANDBY_MODE (0x1 << 22) /* Standby mode */
+#define IMPMCR_PC3_AUTO_MODE (0x3 << 22) /* Automatically controlled */
+
+#define IMPMCR_PC2 (0x3 << 20) /* Bank 2 Power Control */
+#define IMPMCR_PC2_RUN_MODE (0x0 << 20) /* Run mode */
+#define IMPMCR_PC2_STANDBY_MODE (0x1 << 20) /* Standby mode */
+#define IMPMCR_PC2_AUTO_MODE (0x3 << 20) /* Automatically controlled */
+
+#define IMPMCR_PC1 (0x3 << 18) /* Bank 1 Power Control */
+#define IMPMCR_PC1_RUN_MODE (0x0 << 18) /* Run mode */
+#define IMPMCR_PC1_STANDBY_MODE (0x1 << 18) /* Standby mode */
+#define IMPMCR_PC1_AUTO_MODE (0x3 << 18) /* Automatically controlled */
+
+#define IMPMCR_PC0 (0x3 << 16) /* Bank 0 Power Control */
+#define IMPMCR_PC0_RUN_MODE (0x0 << 16) /* Run mode */
+#define IMPMCR_PC0_STANDBY_MODE (0x1 << 16) /* Standby mode */
+#define IMPMCR_PC0_AUTO_MODE (0x3 << 16) /* Automatically controlled */
+
+#define IMPMCR_AW3 (1 << 11) /* Bank 3 Automatic Wake-up enable */
+#define IMPMCR_AW2 (1 << 10) /* Bank 2 Automatic Wake-up enable */
+#define IMPMCR_AW1 (1 << 9) /* Bank 1 Automatic Wake-up enable */
+#define IMPMCR_AW0 (1 << 8) /* Bank 0 Automatic Wake-up enable */
+
+#define IMPMCR_DST (0xFF << 0) /* Delay Standby Time, ms */
+
+#define IMPMSR_PS3 (0x3 << 6) /* Bank 3 Power Status: */
+#define IMPMSR_PS3_RUN_MODE (0x0 << 6) /* Run mode */
+#define IMPMSR_PS3_STANDBY_MODE (0x1 << 6) /* Standby mode */
+
+#define IMPMSR_PS2 (0x3 << 4) /* Bank 2 Power Status: */
+#define IMPMSR_PS2_RUN_MODE (0x0 << 4) /* Run mode */
+#define IMPMSR_PS2_STANDBY_MODE (0x1 << 4) /* Standby mode */
+
+#define IMPMSR_PS1 (0x3 << 2) /* Bank 1 Power Status: */
+#define IMPMSR_PS1_RUN_MODE (0x0 << 2) /* Run mode */
+#define IMPMSR_PS1_STANDBY_MODE (0x1 << 2) /* Standby mode */
+
+#define IMPMSR_PS0 (0x3 << 0) /* Bank 0 Power Status: */
+#define IMPMSR_PS0_RUN_MODE (0x0 << 0) /* Run mode */
+#define IMPMSR_PS0_STANDBY_MODE (0x1 << 0) /* Standby mode */
+
+#endif
+
+/* PWRMODE register M field values */
+
+#define PWRMODE_IDLE 0x1
+#define PWRMODE_STANDBY 0x2
+#define PWRMODE_SLEEP 0x3
+#define PWRMODE_DEEPSLEEP 0x7
+
+#endif