--- /dev/null
+#ifndef _ASM_M32R_SERIAL_H
+#define _ASM_M32R_SERIAL_H
+
+/* $Id$ */
+
+/* orig : i386 2.4.18 */
+
+/*
+ * include/asm-m32r/serial.h
+ */
+
+#include <linux/config.h>
+#include <asm/m32r.h>
+
+/*
+ * This assumes you have a 1.8432 MHz clock for your UART.
+ *
+ * It'd be nice if someone built a serial card with a 24.576 MHz
+ * clock, since the 16550A is capable of handling a top speed of 1.5
+ * megabits/second; but this requires the faster clock.
+ */
+#define BASE_BAUD ( 1843200 / 16 )
+
+/* Standard COM flags (except for COM4, because of the 8514 problem) */
+#ifdef CONFIG_SERIAL_DETECT_IRQ
+#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
+#define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
+#else
+#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
+#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
+#endif
+
+#ifdef CONFIG_SERIAL_MANY_PORTS
+#define FOURPORT_FLAGS ASYNC_FOURPORT
+#define ACCENT_FLAGS 0
+#define BOCA_FLAGS 0
+#define HUB6_FLAGS 0
+#define RS_TABLE_SIZE 64
+#else
+#define RS_TABLE_SIZE
+#endif
+
+#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
+
+/*
+ * The following define the access methods for the HUB6 card. All
+ * access is through two ports for all 24 possible chips. The card is
+ * selected through the high 2 bits, the port on that card with the
+ * "middle" 3 bits, and the register on that port with the bottom
+ * 3 bits.
+ *
+ * While the access port and interrupt is configurable, the default
+ * port locations are 0x302 for the port control register, and 0x303
+ * for the data read/write register. Normally, the interrupt is at irq3
+ * but can be anything from 3 to 7 inclusive. Note that using 3 will
+ * require disabling com2.
+ */
+
+#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
+
+#define STD_SERIAL_PORT_DEFNS \
+ /* UART CLK PORT IRQ FLAGS */ \
+ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
+ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
+ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
+ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
+
+
+#ifdef CONFIG_SERIAL_MANY_PORTS
+#define EXTRA_SERIAL_PORT_DEFNS \
+ { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
+ { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
+ { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
+ { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
+ { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
+ { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
+ { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
+ { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
+ { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
+ { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
+ { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
+ { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
+ { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
+ { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
+ { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
+ { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
+ { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
+ { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
+ { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
+ { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
+ { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
+ { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
+ { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
+ { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
+ { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
+ { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
+ { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
+ { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
+#else
+#define EXTRA_SERIAL_PORT_DEFNS
+#endif
+
+/* You can have up to four HUB6's in the system, but I've only
+ * included two cards here for a total of twelve ports.
+ */
+#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
+#define HUB6_SERIAL_PORT_DFNS \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
+ { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
+#else
+#define HUB6_SERIAL_PORT_DFNS
+#endif
+
+#ifdef CONFIG_MCA
+#define MCA_SERIAL_PORT_DFNS \
+ { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
+ { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
+ { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
+ { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
+ { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
+ { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
+#else
+#define MCA_SERIAL_PORT_DFNS
+#endif
+
+#ifndef CONFIG_PLAT_USRV
+#define SERIAL_PORT_DFNS \
+ STD_SERIAL_PORT_DEFNS \
+ EXTRA_SERIAL_PORT_DEFNS \
+ HUB6_SERIAL_PORT_DFNS \
+ MCA_SERIAL_PORT_DFNS
+
+#else /* CONFIG_PLAT_USRV */
+
+#define SERIAL_PORT_DFNS \
+ /* UART CLK PORT IRQ FLAGS */ \
+ { 0, BASE_BAUD, 0x3F8, PLD_IRQ_UART0, STD_COM_FLAGS }, /* ttyS0 */ \
+ { 0, BASE_BAUD, 0x2F8, PLD_IRQ_UART1, STD_COM_FLAGS }, /* ttyS1 */
+#endif /* CONFIG_PLAT_USRV */
+
+#endif /* _ASM_M32R_SERIAL_H */
git://git.onelab.eu / linux-2.6.git / blobdiff