#ifndef __ASM_PARISC_PCI_H
#define __ASM_PARISC_PCI_H
-#include <linux/config.h>
#include <asm/scatterlist.h>
+
+
/*
** HP PCI platforms generally support multiple bus adapters.
** (workstations 1-~4, servers 2-~32)
*/
#define PCI_MAX_BUSSES 256
+
+/* To be used as: mdelay(pci_post_reset_delay);
+ *
+ * post_reset is the time the kernel should stall to prevent anyone from
+ * accessing the PCI bus once #RESET is de-asserted.
+ * PCI spec somewhere says 1 second but with multi-PCI bus systems,
+ * this makes the boot time much longer than necessary.
+ * 20ms seems to work for all the HP PCI implementations to date.
+ */
+#define pci_post_reset_delay 50
+
+
/*
** pci_hba_data (aka H2P_OBJECT in HP/UX)
**
** Data needed by pcibios layer belongs here.
*/
struct pci_hba_data {
- unsigned long base_addr; /* aka Host Physical Address */
+ void __iomem *base_addr; /* aka Host Physical Address */
const struct parisc_device *dev; /* device from PA bus walk */
struct pci_bus *hba_bus; /* primary PCI bus below HBA */
int hba_num; /* I/O port space access "key" */
struct resource lmmio_space; /* bus addresses < 4Gb */
struct resource elmmio_space; /* additional bus addresses < 4Gb */
struct resource gmmio_space; /* bus addresses > 4Gb */
+
/* NOTE: Dino code assumes it can use *all* of the lmmio_space,
* elmmio_space and gmmio_space as a contiguous array of
* resources. This #define represents the array size */
unsigned long lmmio_space_offset; /* CPU view - PCI view */
void * iommu; /* IOMMU this device is under */
/* REVISIT - spinlock to protect resources? */
+
+ #define HBA_NAME_SIZE 16
+ char io_name[HBA_NAME_SIZE];
+ char lmmio_name[HBA_NAME_SIZE];
+ char elmmio_name[HBA_NAME_SIZE];
+ char gmmio_name[HBA_NAME_SIZE];
};
#define HBA_DATA(d) ((struct pci_hba_data *) (d))
#define PCI_PORT_HBA(a) ((a) >> HBA_PORT_SPACE_BITS)
#define PCI_PORT_ADDR(a) ((a) & (HBA_PORT_SPACE_SIZE - 1))
+#ifdef CONFIG_64BIT
+#define PCI_F_EXTEND 0xffffffff00000000UL
+#define PCI_IS_LMMIO(hba,a) pci_is_lmmio(hba,a)
+
+/* We need to know if an address is LMMMIO or GMMIO.
+ * LMMIO requires mangling and GMMIO we must use as-is.
+ */
+static __inline__ int pci_is_lmmio(struct pci_hba_data *hba, unsigned long a)
+{
+ return(((a) & PCI_F_EXTEND) == PCI_F_EXTEND);
+}
+
/*
** Convert between PCI (IO_VIEW) addresses and processor (PA_VIEW) addresses.
-** Note that we currently support only LMMIO.
+** See pci.c for more conversions used by Generic PCI code.
+**
+** Platform characteristics/firmware guarantee that
+** (1) PA_VIEW - IO_VIEW = lmmio_offset for both LMMIO and ELMMIO
+** (2) PA_VIEW == IO_VIEW for GMMIO
*/
-#define PCI_BUS_ADDR(hba,a) ((a) - hba->lmmio_space_offset)
-#define PCI_HOST_ADDR(hba,a) ((a) + hba->lmmio_space_offset)
+#define PCI_BUS_ADDR(hba,a) (PCI_IS_LMMIO(hba,a) \
+ ? ((a) - hba->lmmio_space_offset) /* mangle LMMIO */ \
+ : (a)) /* GMMIO */
+#define PCI_HOST_ADDR(hba,a) (((a) & PCI_F_EXTEND) == 0 \
+ ? (a) + hba->lmmio_space_offset \
+ : (a))
+
+#else /* !CONFIG_64BIT */
+
+#define PCI_BUS_ADDR(hba,a) (a)
+#define PCI_HOST_ADDR(hba,a) (a)
+#define PCI_F_EXTEND 0UL
+#define PCI_IS_LMMIO(hba,a) (1) /* 32-bit doesn't support GMMIO */
+
+#endif /* !CONFIG_64BIT */
/*
** KLUGE: linux/pci.h include asm/pci.h BEFORE declaring struct pci_bus
struct pci_bus;
struct pci_dev;
-/* The PCI address space does equal the physical memory
- * address space. The networking and block device layers use
+/*
+ * If the PCI device's view of memory is the same as the CPU's view of memory,
+ * PCI_DMA_BUS_IS_PHYS is true. The networking and block device layers use
* this boolean for bounce buffer decisions.
*/
-#define PCI_DMA_BUS_IS_PHYS (1)
+#ifdef CONFIG_PA20
+/* All PA-2.0 machines have an IOMMU. */
+#define PCI_DMA_BUS_IS_PHYS 0
+#define parisc_has_iommu() do { } while (0)
+#else
+
+#if defined(CONFIG_IOMMU_CCIO) || defined(CONFIG_IOMMU_SBA)
+extern int parisc_bus_is_phys; /* in arch/parisc/kernel/setup.c */
+#define PCI_DMA_BUS_IS_PHYS parisc_bus_is_phys
+#define parisc_has_iommu() do { parisc_bus_is_phys = 0; } while (0)
+#else
+#define PCI_DMA_BUS_IS_PHYS 1
+#define parisc_has_iommu() do { } while (0)
+#endif
+
+#endif /* !CONFIG_PA20 */
+
/*
** Most PCI devices (eg Tulip, NCR720) also export the same registers
** to both MMIO and I/O port space. Due to poor performance of I/O Port
-** access under HP PCI bus adapters, strongly reccomend use of MMIO
+** access under HP PCI bus adapters, strongly recommend the use of MMIO
** address space.
**
** While I'm at it more PA programming notes:
*/
extern struct pci_port_ops *pci_port;
extern struct pci_bios_ops *pci_bios;
-extern int pci_post_reset_delay; /* delay after de-asserting #RESET */
-extern int pci_hba_count;
-extern struct pci_hba_data *parisc_pci_hba[];
#ifdef CONFIG_PCI
extern void pcibios_register_hba(struct pci_hba_data *);
#endif
/*
-** used by drivers/pci/pci.c:pci_do_scan_bus()
-** 0 == check if bridge is numbered before re-numbering.
-** 1 == pci_do_scan_bus() should automatically number all PCI-PCI bridges.
-**
-** REVISIT:
-** To date, only alpha sets this to one. We'll need to set this
-** to zero for legacy platforms and one for PAT platforms.
-*/
-#define pcibios_assign_all_busses() (pdc_type == PDC_TYPE_PAT)
-#define pcibios_scan_all_fns(a, b) 0
+ * pcibios_assign_all_busses() is used in drivers/pci/pci.c:pci_do_scan_bus()
+ * 0 == check if bridge is numbered before re-numbering.
+ * 1 == pci_do_scan_bus() should automatically number all PCI-PCI bridges.
+ *
+ * We *should* set this to zero for "legacy" platforms and one
+ * for PAT platforms.
+ *
+ * But legacy platforms also need to renumber the busses below a Host
+ * Bus controller. Adding a 4-port Tulip card on the first PCI root
+ * bus of a C200 resulted in the secondary bus being numbered as 1.
+ * The second PCI host bus controller's root bus had already been
+ * assigned bus number 1 by firmware and sysfs complained.
+ *
+ * Firmware isn't doing anything wrong here since each controller
+ * is its own PCI domain. It's simpler and easier for us to renumber
+ * the busses rather than treat each Dino as a separate PCI domain.
+ * Eventually, we may want to introduce PCI domains for Superdome or
+ * rp7420/8420 boxes and then revisit this issue.
+ */
+#define pcibios_assign_all_busses() (1)
+#define pcibios_scan_all_fns(a, b) (0)
#define PCIBIOS_MIN_IO 0x10
#define PCIBIOS_MIN_MEM 0x1000 /* NBPG - but pci/setup-res.c dies */
/* export the pci_ DMA API in terms of the dma_ one */
#include <asm-generic/pci-dma-compat.h>
+#ifdef CONFIG_PCI
+static inline void pci_dma_burst_advice(struct pci_dev *pdev,
+ enum pci_dma_burst_strategy *strat,
+ unsigned long *strategy_parameter)
+{
+ unsigned long cacheline_size;
+ u8 byte;
+
+ pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &byte);
+ if (byte == 0)
+ cacheline_size = 1024;
+ else
+ cacheline_size = (int) byte * 4;
+
+ *strat = PCI_DMA_BURST_MULTIPLE;
+ *strategy_parameter = cacheline_size;
+}
+#endif
+
extern void
pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
struct resource *res);
+extern void
+pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res,
+ struct pci_bus_region *region);
+
+static inline struct resource *
+pcibios_select_root(struct pci_dev *pdev, struct resource *res)
+{
+ struct resource *root = NULL;
+
+ if (res->flags & IORESOURCE_IO)
+ root = &ioport_resource;
+ if (res->flags & IORESOURCE_MEM)
+ root = &iomem_resource;
+
+ return root;
+}
+
static inline void pcibios_add_platform_entries(struct pci_dev *dev)
{
}
+static inline void pcibios_penalize_isa_irq(int irq, int active)
+{
+ /* We don't need to penalize isa irq's */
+}
+
+static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel)
+{
+ return channel ? 15 : 14;
+}
+
#endif /* __ASM_PARISC_PCI_H */