fedora core 6 1.2949 + vserver 2.2.0

[linux-2.6.git] / include / linux / serialP.h

diff --git a/include/linux/serialP.h b/include/linux/serialP.h
index 93f7492..e811a61 100644 (file)
--- a/include/linux/serialP.h
+++ b/include/linux/serialP.h
@@ -19,8 +19,6 @@
  * For definitions of the flags field, see tty.h
  */
 
-#include <linux/version.h>
-#include <linux/config.h>
 #include <linux/termios.h>
 #include <linux/workqueue.h>
 #include <linux/interrupt.h>
@@ -130,48 +128,15 @@ struct rs_multiport_struct {
  * reason (mips != alpha!)
  */
 #define ALPHA_KLUDGE_MCR  (UART_MCR_OUT2 | UART_MCR_OUT1)
+#elif defined(CONFIG_SBC8560)
+/*
+ * WindRiver did something similarly broken on their SBC8560 board. The
+ * UART tristates its IRQ output while OUT2 is clear, but they pulled
+ * the interrupt line _up_ instead of down, so if we register the IRQ
+ * while the UART is in that state, we die in an IRQ storm. */
+#define ALPHA_KLUDGE_MCR (UART_MCR_OUT2)
 #else
 #define ALPHA_KLUDGE_MCR 0
 #endif
 
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK      0x0007
-#define SPCI_FL_BASE0  0x0000
-#define SPCI_FL_BASE1  0x0001
-#define SPCI_FL_BASE2  0x0002
-#define SPCI_FL_BASE3  0x0003
-#define SPCI_FL_BASE4  0x0004
-#define SPCI_FL_GET_BASE(x)    (x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK       (0x0007 << 4)
-#define SPCI_FL_IRQBASE0       (0x0000 << 4)
-#define SPCI_FL_IRQBASE1       (0x0001 << 4)
-#define SPCI_FL_IRQBASE2       (0x0002 << 4)
-#define SPCI_FL_IRQBASE3       (0x0003 << 4)
-#define SPCI_FL_IRQBASE4       (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x)        ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers), 
-   else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE     0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE      0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE    0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP  0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ       0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP          0x2000
-
-#define SPCI_FL_PNPDEFAULT     (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
 #endif /* _LINUX_SERIAL_H */