/* This command enables or disables an Open vSwitch extension that allows a
* controller to specify the OpenFlow table to which a flow should be added,
* instead of having the switch decide which table is most appropriate as
- * required by OpenFlow 1.0. By default, the extension is disabled.
+ * required by OpenFlow 1.0. Because NXM was designed as an extension to
+ * OpenFlow 1.0, the extension applies equally to ofp10_flow_mod and
+ * nx_flow_mod. By default, the extension is disabled.
*
* When this feature is enabled, Open vSwitch treats struct ofp10_flow_mod's
- * 16-bit 'command' member as two separate fields. The upper 8 bits are used
- * as the table ID, the lower 8 bits specify the command as usual. A table ID
- * of 0xff is treated like a wildcarded table ID.
+ * and struct nx_flow_mod's 16-bit 'command' member as two separate fields.
+ * The upper 8 bits are used as the table ID, the lower 8 bits specify the
+ * command as usual. A table ID of 0xff is treated like a wildcarded table ID.
*
* The specific treatment of the table ID depends on the type of flow mod:
*
NXAST_WRITE_METADATA, /* struct nx_action_write_metadata */
NXAST_PUSH_MPLS, /* struct nx_action_push_mpls */
NXAST_POP_MPLS, /* struct nx_action_pop_mpls */
+ NXAST_SET_MPLS_TTL, /* struct nx_action_ttl */
+ NXAST_DEC_MPLS_TTL, /* struct nx_action_header */
+ NXAST_STACK_PUSH, /* struct nx_action_stack */
+ NXAST_STACK_POP, /* struct nx_action_stack */
};
/* Header for Nicira-defined actions. */
};
OFP_ASSERT(sizeof(struct nx_action_reg_load) == 24);
+/* Action structure for NXAST_STACK_PUSH and NXAST_STACK_POP.
+ *
+ * Pushes (or pops) field[offset: offset + n_bits] to (or from)
+ * top of the stack.
+ */
+struct nx_action_stack {
+ ovs_be16 type; /* OFPAT_VENDOR. */
+ ovs_be16 len; /* Length is 16. */
+ ovs_be32 vendor; /* NX_VENDOR_ID. */
+ ovs_be16 subtype; /* NXAST_STACK_PUSH or NXAST_STACK_POP. */
+ ovs_be16 offset; /* Bit offset into the field. */
+ ovs_be32 field; /* The field used for push or pop. */
+ ovs_be16 n_bits; /* (n_bits + 1) bits of the field. */
+ uint8_t zero[6]; /* Reserved, must be zero. */
+};
+OFP_ASSERT(sizeof(struct nx_action_stack) == 24);
+
/* Action structure for NXAST_NOTE.
*
* This action has no effect. It is variable length. The switch does not
*/
struct nx_flow_mod {
ovs_be64 cookie; /* Opaque controller-issued identifier. */
- ovs_be16 command; /* One of OFPFC_*. */
+ ovs_be16 command; /* OFPFC_* + possibly a table ID (see comment
+ * on struct nx_flow_mod_table_id). */
ovs_be16 idle_timeout; /* Idle time before discarding (seconds). */
ovs_be16 hard_timeout; /* Max time before discarding (seconds). */
ovs_be16 priority; /* Priority level of flow entry. */
};
OFP_ASSERT(sizeof(struct nx_flow_mod) == 32);
-/* NXT_FLOW_REMOVED (analogous to OFPT_FLOW_REMOVED). */
+/* NXT_FLOW_REMOVED (analogous to OFPT_FLOW_REMOVED).
+ *
+ * 'table_id' is present only in Open vSwitch 1.11 and later. In earlier
+ * versions of Open vSwitch, this is a padding byte that is always zeroed.
+ * Therefore, a 'table_id' value of 0 indicates that the table ID is not known,
+ * and other values may be interpreted as one more than the flow's former table
+ * ID. */
struct nx_flow_removed {
ovs_be64 cookie; /* Opaque controller-issued identifier. */
ovs_be16 priority; /* Priority level of flow entry. */
uint8_t reason; /* One of OFPRR_*. */
- uint8_t pad[1]; /* Align to 32-bits. */
+ uint8_t table_id; /* Flow's former table ID, plus one. */
ovs_be32 duration_sec; /* Time flow was alive in seconds. */
ovs_be32 duration_nsec; /* Time flow was alive in nanoseconds beyond
duration_sec. */
};
OFP_ASSERT(sizeof(struct nx_action_pop_mpls) == 16);
+/* Action structure for NXAST_SET_MPLS_TTL. */
+struct nx_action_mpls_ttl {
+ ovs_be16 type; /* OFPAT_VENDOR. */
+ ovs_be16 len; /* Length is 8. */
+ ovs_be32 vendor; /* NX_VENDOR_ID. */
+ ovs_be16 subtype; /* NXAST_SET_MPLS_TTL. */
+ uint8_t ttl; /* TTL */
+ uint8_t pad[5];
+};
+OFP_ASSERT(sizeof(struct nx_action_mpls_ttl) == 16);
+
#endif /* openflow/nicira-ext.h */