uint16_t error; /* Used by ODP_FLOW_GET. */
};
-/*
- * The datapath protocol adopts the Linux convention for TCI fields: if an
- * 802.1Q header is present then its TCI value is used verbatim except that the
- * CFI bit (0x1000) is always set to 1, and all-bits-zero indicates no 802.1Q
- * header.
- */
-#define ODP_TCI_PRESENT 0x1000 /* CFI bit */
-
-struct odp_flow_key {
- ovs_be64 tun_id; /* Encapsulating tunnel ID. */
- ovs_be32 nw_src; /* IP source address. */
- ovs_be32 nw_dst; /* IP destination address. */
- uint16_t in_port; /* Input switch port. */
- ovs_be16 dl_tci; /* All zeros if 802.1Q header absent,
- * ODP_TCI_PRESENT set if present. */
- ovs_be16 dl_type; /* Ethernet frame type. */
- ovs_be16 tp_src; /* TCP/UDP source port. */
- ovs_be16 tp_dst; /* TCP/UDP destination port. */
- uint8_t dl_src[6]; /* Ethernet source address. */
- uint8_t dl_dst[6]; /* Ethernet destination address. */
- uint8_t nw_proto; /* IP protocol or lower 8 bits of
- ARP opcode. */
- uint8_t nw_tos; /* IP ToS (DSCP field, 6 bits). */
+enum odp_key_type {
+ ODP_KEY_ATTR_UNSPEC,
+ ODP_KEY_ATTR_TUN_ID, /* 64-bit tunnel ID */
+ ODP_KEY_ATTR_IN_PORT, /* 32-bit ODP port number */
+ ODP_KEY_ATTR_ETHERNET, /* struct odp_key_ethernet */
+ ODP_KEY_ATTR_8021Q, /* struct odp_key_8021q */
+ ODP_KEY_ATTR_ETHERTYPE, /* 16-bit Ethernet type */
+ ODP_KEY_ATTR_IPV4, /* struct odp_key_ipv4 */
+ ODP_KEY_ATTR_TCP, /* struct odp_key_tcp */
+ ODP_KEY_ATTR_UDP, /* struct odp_key_udp */
+ ODP_KEY_ATTR_ICMP, /* struct odp_key_icmp */
+ ODP_KEY_ATTR_ARP, /* struct odp_key_arp */
+ __ODP_KEY_ATTR_MAX
+};
+
+#define ODP_KEY_ATTR_MAX (__ODP_KEY_ATTR_MAX - 1)
+
+struct odp_key_ethernet {
+ uint8_t eth_src[6];
+ uint8_t eth_dst[6];
+};
+
+struct odp_key_8021q {
+ ovs_be16 q_tpid;
+ ovs_be16 q_tci;
+};
+
+struct odp_key_ipv4 {
+ ovs_be32 ipv4_src;
+ ovs_be32 ipv4_dst;
+ uint8_t ipv4_proto;
+ uint8_t ipv4_tos;
+};
+
+struct odp_key_tcp {
+ ovs_be16 tcp_src;
+ ovs_be16 tcp_dst;
+};
+
+struct odp_key_udp {
+ ovs_be16 udp_src;
+ ovs_be16 udp_dst;
+};
+
+struct odp_key_icmp {
+ uint8_t icmp_type;
+ uint8_t icmp_code;
+};
+
+struct odp_key_arp {
+ ovs_be32 arp_sip;
+ ovs_be32 arp_tip;
+ ovs_be16 arp_op;
};
/* Flags for ODP_FLOW. */
struct odp_flow {
struct odp_flow_stats stats;
- struct odp_flow_key key;
+ struct nlattr *key;
+ uint32_t key_len;
struct nlattr *actions;
uint32_t actions_len;
uint32_t flags;
ODPAT_STRIP_VLAN, /* Strip the 802.1q header. */
ODPAT_SET_DL_SRC, /* Ethernet source address. */
ODPAT_SET_DL_DST, /* Ethernet destination address. */
- ODPAT_SET_NW_SRC, /* IP source address. */
- ODPAT_SET_NW_DST, /* IP destination address. */
+ ODPAT_SET_NW_SRC, /* IPv4 source address. */
+ ODPAT_SET_NW_DST, /* IPv4 destination address. */
ODPAT_SET_NW_TOS, /* IP ToS/DSCP field (6 bits). */
ODPAT_SET_TP_SRC, /* TCP/UDP source port. */
ODPAT_SET_TP_DST, /* TCP/UDP destination port. */
uint16_t mtu;
};
-/* Values below this cutoff are 802.3 packets and the two bytes
- * following MAC addresses are used as a frame length. Otherwise, the
- * two bytes are used as the Ethernet type.
- */
-#define ODP_DL_TYPE_ETH2_CUTOFF 0x0600
-
-/* Value of dl_type to indicate that the frame does not include an
- * Ethernet type.
- */
-#define ODP_DL_TYPE_NOT_ETH_TYPE 0x05ff
-
#endif /* openvswitch/datapath-protocol.h */