--- /dev/null
+/*
+ * usbus428.c - ALSA USB US-428 Driver
+ *
+2004-07-13 Karsten Wiese
+ Version 0.7.1:
+ Don't sleep in START/STOP callbacks anymore.
+ us428 channels C/D not handled just for this version, sorry.
+
+2004-06-21 Karsten Wiese
+ Version 0.6.4:
+ Temporarely suspend midi input
+ to sanely call usb_set_interface() when setting format.
+
+2004-06-12 Karsten Wiese
+ Version 0.6.3:
+ Made it thus the following rule is enforced:
+ "All pcm substreams of one usX2Y have to operate at the same rate & format."
+
+2004-04-06 Karsten Wiese
+ Version 0.6.0:
+ Runs on 2.6.5 kernel without any "--with-debug=" things.
+ us224 reported running.
+
+2004-01-14 Karsten Wiese
+ Version 0.5.1:
+ Runs with 2.6.1 kernel.
+
+2003-12-30 Karsten Wiese
+ Version 0.4.1:
+ Fix 24Bit 4Channel capturing for the us428.
+
+2003-11-27 Karsten Wiese, Martin Langer
+ Version 0.4:
+ us122 support.
+ us224 could be tested by uncommenting the sections containing USB_ID_US224
+
+2003-11-03 Karsten Wiese
+ Version 0.3:
+ 24Bit support.
+ "arecord -D hw:1 -c 2 -r 48000 -M -f S24_3LE|aplay -D hw:1 -c 2 -r 48000 -M -f S24_3LE" works.
+
+2003-08-22 Karsten Wiese
+ Version 0.0.8:
+ Removed EZUSB Firmware. First Stage Firmwaredownload is now done by tascam-firmware downloader.
+ See:
+ http://usb-midi-fw.sourceforge.net/tascam-firmware.tar.gz
+
+2003-06-18 Karsten Wiese
+ Version 0.0.5:
+ changed to compile with kernel 2.4.21 and alsa 0.9.4
+
+2002-10-16 Karsten Wiese
+ Version 0.0.4:
+ compiles again with alsa-current.
+ USB_ISO_ASAP not used anymore (most of the time), instead
+ urb->start_frame is calculated here now, some calls inside usb-driver don't need to happen anymore.
+
+ To get the best out of this:
+ Disable APM-support in the kernel as APM-BIOS calls (once each second) hard disable interrupt for many precious milliseconds.
+ This helped me much on my slowish PII 400 & PIII 500.
+ ACPI yet untested but might cause the same bad behaviour.
+ Use a kernel with lowlatency and preemptiv patches applied.
+ To autoload snd-usb-midi append a line
+ post-install snd-usb-us428 modprobe snd-usb-midi
+ to /etc/modules.conf.
+
+ known problems:
+ sliders, knobs, lights not yet handled except MASTER Volume slider.
+ "pcm -c 2" doesn't work. "pcm -c 2 -m direct_interleaved" does.
+ KDE3: "Enable full duplex operation" deadlocks.
+
+
+2002-08-31 Karsten Wiese
+ Version 0.0.3: audio also simplex;
+ simplifying: iso urbs only 1 packet, melted structs.
+ ASYNC_UNLINK not used anymore: no more crashes so far.....
+ for alsa 0.9 rc3.
+
+2002-08-09 Karsten Wiese
+ Version 0.0.2: midi works with snd-usb-midi, audio (only fullduplex now) with i.e. bristol.
+ The firmware has been sniffed from win2k us-428 driver 3.09.
+
+ * Copyright (c) 2002 Karsten Wiese
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+*/
+
+#include <sound/driver.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/interrupt.h>
+#include <linux/usb.h>
+#include <sound/core.h>
+#include <sound/initval.h>
+#include <sound/pcm.h>
+
+#include <sound/rawmidi.h>
+#include "usx2y.h"
+#include "usbusx2y.h"
+#include "usX2Yhwdep.h"
+
+
+
+MODULE_AUTHOR("Karsten Wiese <annabellesgarden@yahoo.de>");
+MODULE_DESCRIPTION("TASCAM "NAME_ALLCAPS" Version 0.7.2");
+MODULE_LICENSE("GPL");
+MODULE_SUPPORTED_DEVICE("{{TASCAM(0x1604), "NAME_ALLCAPS"(0x8001)(0x8005)(0x8007) }}");
+
+static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-max */
+static char* id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* Id for this card */
+static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; /* Enable this card */
+static int boot_devs;
+
+module_param_array(index, int, boot_devs, 0444);
+MODULE_PARM_DESC(index, "Index value for "NAME_ALLCAPS".");
+module_param_array(id, charp, boot_devs, 0444);
+MODULE_PARM_DESC(id, "ID string for "NAME_ALLCAPS".");
+module_param_array(enable, bool, boot_devs, 0444);
+MODULE_PARM_DESC(enable, "Enable "NAME_ALLCAPS".");
+
+
+static int snd_usX2Y_card_used[SNDRV_CARDS];
+
+static void usX2Y_usb_disconnect(struct usb_device* usb_device, void* ptr);
+static void snd_usX2Y_card_private_free(snd_card_t *card);
+
+/*
+ * pipe 4 is used for switching the lamps, setting samplerate, volumes ....
+ */
+static void i_usX2Y_Out04Int(struct urb* urb, struct pt_regs *regs)
+{
+#ifdef CONFIG_SND_DEBUG
+ if (urb->status) {
+ int i;
+ usX2Ydev_t* usX2Y = urb->context;
+ for (i = 0; i < 10 && usX2Y->AS04.urb[i] != urb; i++);
+ snd_printdd("i_usX2Y_Out04Int() urb %i status=%i\n", i, urb->status);
+ }
+#endif
+}
+
+static void i_usX2Y_In04Int(struct urb* urb, struct pt_regs *regs)
+{
+ int err = 0;
+ usX2Ydev_t *usX2Y = urb->context;
+ us428ctls_sharedmem_t *us428ctls = usX2Y->us428ctls_sharedmem;
+
+ usX2Y->In04IntCalls++;
+
+ if (urb->status) {
+ snd_printdd("Interrupt Pipe 4 came back with status=%i\n", urb->status);
+ return;
+ }
+
+ // printk("%i:0x%02X ", 8, (int)((unsigned char*)usX2Y->In04Buf)[8]); Master volume shows 0 here if fader is at max during boot ?!?
+ if (us428ctls) {
+ int diff = -1;
+ if (-2 == us428ctls->CtlSnapShotLast) {
+ diff = 0;
+ memcpy(usX2Y->In04Last, usX2Y->In04Buf, sizeof(usX2Y->In04Last));
+ us428ctls->CtlSnapShotLast = -1;
+ } else {
+ int i;
+ for (i = 0; i < 21; i++) {
+ if (usX2Y->In04Last[i] != ((char*)usX2Y->In04Buf)[i]) {
+ if (diff < 0)
+ diff = i;
+ usX2Y->In04Last[i] = ((char*)usX2Y->In04Buf)[i];
+ }
+ }
+ }
+ if (0 <= diff) {
+ int n = us428ctls->CtlSnapShotLast + 1;
+ if (n >= N_us428_ctl_BUFS || n < 0)
+ n = 0;
+ memcpy(us428ctls->CtlSnapShot + n, usX2Y->In04Buf, sizeof(us428ctls->CtlSnapShot[0]));
+ us428ctls->CtlSnapShotDiffersAt[n] = diff;
+ us428ctls->CtlSnapShotLast = n;
+ wake_up(&usX2Y->us428ctls_wait_queue_head);
+ }
+ }
+
+
+ if (usX2Y->US04) {
+ if (0 == usX2Y->US04->submitted)
+ do
+ err = usb_submit_urb(usX2Y->US04->urb[usX2Y->US04->submitted++], GFP_ATOMIC);
+ while (!err && usX2Y->US04->submitted < usX2Y->US04->len);
+ } else
+ if (us428ctls && us428ctls->p4outLast >= 0 && us428ctls->p4outLast < N_us428_p4out_BUFS) {
+ if (us428ctls->p4outLast != us428ctls->p4outSent) {
+ int j, send = us428ctls->p4outSent + 1;
+ if (send >= N_us428_p4out_BUFS)
+ send = 0;
+ for (j = 0; j < URBS_AsyncSeq && !err; ++j)
+ if (0 == usX2Y->AS04.urb[j]->status) {
+ us428_p4out_t *p4out = us428ctls->p4out + send; // FIXME if more then 1 p4out is new, 1 gets lost.
+ usb_fill_bulk_urb(usX2Y->AS04.urb[j], usX2Y->chip.dev,
+ usb_sndbulkpipe(usX2Y->chip.dev, 0x04), &p4out->val.vol,
+ p4out->type == eLT_Light ? sizeof(us428_lights_t) : 5,
+ i_usX2Y_Out04Int, usX2Y);
+ err = usb_submit_urb(usX2Y->AS04.urb[j], GFP_ATOMIC);
+ us428ctls->p4outSent = send;
+ break;
+ }
+ }
+ }
+
+ if (err) {
+ snd_printk("In04Int() usb_submit_urb err=%i\n", err);
+ }
+
+ urb->dev = usX2Y->chip.dev;
+ usb_submit_urb(urb, GFP_ATOMIC);
+}
+
+/*
+ * Prepare some urbs
+ */
+int usX2Y_AsyncSeq04_init(usX2Ydev_t* usX2Y)
+{
+ int err = 0,
+ i;
+
+ if (NULL == (usX2Y->AS04.buffer = kmalloc(URB_DataLen_AsyncSeq*URBS_AsyncSeq, GFP_KERNEL))) {
+ err = -ENOMEM;
+ } else
+ for (i = 0; i < URBS_AsyncSeq; ++i) {
+ if (NULL == (usX2Y->AS04.urb[i] = usb_alloc_urb(0, GFP_KERNEL))) {
+ err = -ENOMEM;
+ break;
+ }
+ usb_fill_bulk_urb( usX2Y->AS04.urb[i], usX2Y->chip.dev,
+ usb_sndbulkpipe(usX2Y->chip.dev, 0x04),
+ usX2Y->AS04.buffer + URB_DataLen_AsyncSeq*i, 0,
+ i_usX2Y_Out04Int, usX2Y
+ );
+ }
+ return err;
+}
+
+int usX2Y_In04_init(usX2Ydev_t* usX2Y)
+{
+ int err = 0;
+ if (! (usX2Y->In04urb = usb_alloc_urb(0, GFP_KERNEL)))
+ return -ENOMEM;
+
+ if (! (usX2Y->In04Buf = kmalloc(21, GFP_KERNEL))) {
+ usb_free_urb(usX2Y->In04urb);
+ return -ENOMEM;
+ }
+
+ init_waitqueue_head(&usX2Y->In04WaitQueue);
+ usb_fill_int_urb(usX2Y->In04urb, usX2Y->chip.dev, usb_rcvintpipe(usX2Y->chip.dev, 0x4),
+ usX2Y->In04Buf, 21,
+ i_usX2Y_In04Int, usX2Y,
+ 10);
+ err = usb_submit_urb(usX2Y->In04urb, GFP_KERNEL);
+ return err;
+}
+
+static void usX2Y_unlinkSeq(snd_usX2Y_AsyncSeq_t* S)
+{
+ int i;
+ for (i = 0; i < URBS_AsyncSeq; ++i) {
+ if (S[i].urb) {
+ usb_unlink_urb(S->urb[i]);
+ usb_free_urb(S->urb[i]);
+ S->urb[i] = NULL;
+ }
+ }
+ if (S->buffer)
+ kfree(S->buffer);
+}
+
+
+static struct usb_device_id snd_usX2Y_usb_id_table[] = {
+ {
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE,
+ .idVendor = 0x1604,
+ .idProduct = USB_ID_US428
+ },
+ {
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE,
+ .idVendor = 0x1604,
+ .idProduct = USB_ID_US122
+ },
+ {
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE,
+ .idVendor = 0x1604,
+ .idProduct = USB_ID_US224
+ },
+ { /* terminator */ }
+};
+
+static snd_card_t* usX2Y_create_card(struct usb_device* device)
+{
+ int dev;
+ snd_card_t* card;
+ for (dev = 0; dev < SNDRV_CARDS; ++dev)
+ if (enable[dev] && !snd_usX2Y_card_used[dev])
+ break;
+ if (dev >= SNDRV_CARDS)
+ return NULL;
+ card = snd_card_new(index[dev], id[dev], THIS_MODULE, sizeof(usX2Ydev_t));
+ if (!card)
+ return NULL;
+ snd_usX2Y_card_used[usX2Y(card)->chip.index = dev] = 1;
+ card->private_free = snd_usX2Y_card_private_free;
+ usX2Y(card)->chip.dev = device;
+ usX2Y(card)->chip.card = card;
+ init_MUTEX (&usX2Y(card)->open_mutex);
+ INIT_LIST_HEAD(&usX2Y(card)->chip.midi_list);
+ strcpy(card->driver, "USB "NAME_ALLCAPS"");
+ sprintf(card->shortname, "TASCAM "NAME_ALLCAPS"");
+ sprintf(card->longname, "%s (%x:%x if %d at %03d/%03d)",
+ card->shortname,
+ device->descriptor.idVendor, device->descriptor.idProduct,
+ 0,//us428(card)->usbmidi.ifnum,
+ usX2Y(card)->chip.dev->bus->busnum, usX2Y(card)->chip.dev->devnum
+ );
+ snd_card_set_dev(card, &device->dev);
+ return card;
+}
+
+
+static void* usX2Y_usb_probe(struct usb_device* device, struct usb_interface *intf, const struct usb_device_id* device_id)
+{
+ int err;
+ snd_card_t* card;
+ if (device->descriptor.idVendor != 0x1604 ||
+ (device->descriptor.idProduct != USB_ID_US122 &&
+ device->descriptor.idProduct != USB_ID_US224 &&
+ device->descriptor.idProduct != USB_ID_US428) ||
+ !(card = usX2Y_create_card(device)))
+ return NULL;
+ if ((err = usX2Y_hwdep_new(card, device)) < 0 ||
+ (err = snd_card_register(card)) < 0) {
+ snd_card_free(card);
+ return NULL;
+ }
+ return card;
+}
+
+/*
+ * new 2.5 USB kernel API
+ */
+static int snd_usX2Y_probe(struct usb_interface *intf, const struct usb_device_id *id)
+{
+ void *chip;
+ chip = usX2Y_usb_probe(interface_to_usbdev(intf), intf, id);
+ if (chip) {
+ dev_set_drvdata(&intf->dev, chip);
+ return 0;
+ } else
+ return -EIO;
+}
+
+static void snd_usX2Y_disconnect(struct usb_interface *intf)
+{
+ usX2Y_usb_disconnect(interface_to_usbdev(intf),
+ dev_get_drvdata(&intf->dev));
+}
+
+MODULE_DEVICE_TABLE(usb, snd_usX2Y_usb_id_table);
+static struct usb_driver snd_usX2Y_usb_driver = {
+ .owner = THIS_MODULE,
+ .name = "snd-usb-usx2y",
+ .probe = snd_usX2Y_probe,
+ .disconnect = snd_usX2Y_disconnect,
+ .id_table = snd_usX2Y_usb_id_table,
+};
+
+static void snd_usX2Y_card_private_free(snd_card_t *card)
+{
+ if (usX2Y(card)->In04Buf)
+ kfree(usX2Y(card)->In04Buf);
+ usb_free_urb(usX2Y(card)->In04urb);
+ if (usX2Y(card)->us428ctls_sharedmem)
+ snd_free_pages(usX2Y(card)->us428ctls_sharedmem, sizeof(*usX2Y(card)->us428ctls_sharedmem));
+ if (usX2Y(card)->chip.index >= 0 && usX2Y(card)->chip.index < SNDRV_CARDS)
+ snd_usX2Y_card_used[usX2Y(card)->chip.index] = 0;
+}
+
+/*
+ * Frees the device.
+ */
+static void usX2Y_usb_disconnect(struct usb_device* device, void* ptr)
+{
+ if (ptr) {
+ usX2Ydev_t* usX2Y = usX2Y((snd_card_t*)ptr);
+ struct list_head* p;
+ if (usX2Y->chip_status == USX2Y_STAT_CHIP_HUP) // on 2.6.1 kernel snd_usbmidi_disconnect()
+ return; // calls us back. better leave :-) .
+ usX2Y->chip.shutdown = 1;
+ usX2Y->chip_status = USX2Y_STAT_CHIP_HUP;
+ usX2Y_unlinkSeq(&usX2Y->AS04);
+ usb_unlink_urb(usX2Y->In04urb);
+ snd_card_disconnect((snd_card_t*)ptr);
+ /* release the midi resources */
+ list_for_each(p, &usX2Y->chip.midi_list) {
+ snd_usbmidi_disconnect(p, &snd_usX2Y_usb_driver);
+ }
+ if (usX2Y->us428ctls_sharedmem)
+ wake_up(&usX2Y->us428ctls_wait_queue_head);
+ snd_card_free_in_thread((snd_card_t*)ptr);
+ }
+}
+
+static int __init snd_usX2Y_module_init(void)
+{
+ return usb_register(&snd_usX2Y_usb_driver);
+}
+
+static void __exit snd_usX2Y_module_exit(void)
+{
+ usb_deregister(&snd_usX2Y_usb_driver);
+}
+
+module_init(snd_usX2Y_module_init)
+module_exit(snd_usX2Y_module_exit)
git://git.onelab.eu / linux-2.6.git / blobdiff