OpenFlow assigned port number or device name, e.g. \fBeth0\fR.
.
.TP
+\fBdump\-ports\-desc \fIswitch\fR
+Prints to the console detailed information about network devices
+associated with \fIswitch\fR (version 1.7 or later). This is a subset
+of the information provided by the \fBshow\fR command.
+.
+.TP
\fBmod\-port \fIswitch\fR \fInetdev\fR \fIaction\fR
Modify characteristics of an interface monitored by \fIswitch\fR.
\fInetdev\fR can be referred to by its OpenFlow assigned port number or
following:
.
.RS
-.IP \fBup\fR
-Enables the interface. This is equivalent to ``ifconfig up'' on a Unix
-system.
-.
-.IP \fBdown\fR
-Disables the interface. This is equivalent to ``ifconfig down'' on a Unix
-system.
+.IQ \fBup\fR
+.IQ \fBdown\fR
+Enable or disable the interface. This is equivalent to \fBifconfig
+up\fR or \fBifconfig down\fR on a Unix system.
+.
+.IP \fBstp\fR
+.IQ \fBno\-stp\fR
+Enable or disable 802.1D spanning tree protocol (STP) on the
+interface. OpenFlow implementations that don't support STP will
+refuse to enable it.
+.
+.IP \fBreceive\fR
+.IQ \fBno\-receive\fR
+.IQ \fBreceive\-stp\fR
+.IQ \fBno\-receive\-stp\fR
+Enable or disable OpenFlow processing of packets received on this
+interface. When packet processing is disabled, packets will be
+dropped instead of being processed through the OpenFlow table. The
+\fBreceive\fR or \fBno\-receive\fR setting applies to all packets
+except 802.1D spanning tree packets, which are separately controlled
+by \fBreceive\-stp\fR or \fBno\-receive\-stp\fR.
.
.IP \fBforward\fR
-Allows forwarding of traffic on this interface. This is the default posture
-for all ports.
-.
-.IP \fBnoforward\fR
-Disallows forwarding of traffic on this interface.
+.IQ \fBno\-forward\fR
+Allow or disallow forwarding of traffic to this interface. By
+default, forwarding is enabled.
.
.IP \fBflood\fR
-When a \fIflood\fR action is specified, traffic will be sent out this
-interface. This is the default posture for monitored ports.
-.
-.IP \fBnoflood\fR
-When a \fIflood\fR action is specified, traffic will not be sent out
-this interface. This is primarily useful to prevent loops when a
-spanning tree protocol is not in use.
-.
+.IQ \fBno\-flood\fR
+Controls whether an OpenFlow \fBflood\fR action will send traffic out
+this interface. By default, flooding is enabled. Disabling flooding
+is primarily useful to prevent loops when a spanning tree protocol is
+not in use.
+.
+.IP \fBpacket\-in\fR
+.IQ \fBno\-packet\-in\fR
+Controls whether packets received on this interface that do not match
+a flow table entry generate a ``packet in'' message to the OpenFlow
+controller. By default, ``packet in'' messages are enabled.
.RE
+.IP
+The \fBshow\fR command displays (among other information) the
+configuration that \fBmod\-port\fR changes.
.
.IP "\fBget\-frags \fIswitch\fR"
Prints \fIswitch\fR's fragment handling mode. See \fBset\-frags\fR,
Prints to the console all flow entries in \fIswitch\fR's
tables that match \fIflows\fR. If \fIflows\fR is omitted, all flows
in the switch are retrieved. See \fBFlow Syntax\fR, below, for the
-syntax of \fIflows\fR. The output format is described in
+syntax of \fIflows\fR. The output format is described in
\fBTable Entry Output\fR.
.
+.IP
+By default, \fBovs\-ofctl\fR prints flow entries in the same order
+that the switch sends them, which is unlikely to be intuitive or
+consistent. See the description of \fB\-\-sort\fR and \fB\-\-rsort\fR,
+under \fBOPTIONS\fR below, to influence the display order.
+.
.TP
\fBdump\-aggregate \fIswitch \fR[\fIflows\fR]
-Prints to the console aggregate statistics for flows in
+Prints to the console aggregate statistics for flows in
\fIswitch\fR's tables that match \fIflows\fR. If \fIflows\fR is omitted,
the statistics are aggregated across all flows in the switch's flow
tables. See \fBFlow Syntax\fR, below, for the syntax of \fIflows\fR.
the configured controller is disconnected, no traffic is sent, so
monitoring will not show any traffic.
.
-.IP "\fBmonitor \fIswitch\fR [\fImiss-len\fR] [\fIinvalid_ttl\fR]"
+.IP "\fBmonitor \fIswitch\fR [\fImiss-len\fR] [\fBinvalid_ttl\fR] [\fBwatch:\fR[\fIspec\fR...]]"
Connects to \fIswitch\fR and prints to the console all OpenFlow
messages received. Usually, \fIswitch\fR should specify the name of a
bridge in the \fBovs\-vswitchd\fR database.
specified on this argument. (Thus, if \fImiss\-len\fR is not
specified, very little traffic will ordinarily be printed.)
.IP
-.IP
If \fBinvalid_ttl\fR is passed, \fBovs\-ofctl\fR sends an OpenFlow ``set
configuration'' message at connection setup time that requests
-\fIINVALID_TTL_TO_CONTROLLER\fR, so that \fBovs\-ofctl monitor\fR can
-receive ``packets-in'' messages when TTL reaches zero on \fBdec_ttl\fR action.
+\fBINVALID_TTL_TO_CONTROLLER\fR, so that \fBovs\-ofctl monitor\fR can
+receive ``packet-in'' messages when TTL reaches zero on \fBdec_ttl\fR action.
+.IP
+\fBwatch:\fR[\fB\fIspec\fR...] causes \fBovs\-ofctl\fR to send a
+``monitor request'' Nicira extension message to the switch at
+connection setup time. This message causes the switch to send
+information about flow table changes as they occur. The following
+comma-separated \fIspec\fR syntax is available:
+.RS
+.IP "\fB!initial\fR"
+Do not report the switch's initial flow table contents.
+.IP "\fB!add\fR"
+Do not report newly added flows.
+.IP "\fB!delete\fR"
+Do not report deleted flows.
+.IP "\fB!modify\fR"
+Do not report modifications to existing flows.
+.IP "\fB!own\fR"
+Abbreviate changes made to the flow table by \fBovs\-ofctl\fR's own
+connection to the switch. (These could only occur using the
+\fBofctl/send\fR command described below under \fBRUNTIME MANAGEMENT
+COMMANDS\fR.)
+.IP "\fB!actions\fR"
+Do not report actions as part of flow updates.
+.IP "\fBtable=\fInumber\fR"
+Limits the monitoring to the table with the given \fInumber\fR between
+0 and 254. By default, all tables are monitored.
+.IP "\fBout_port=\fIport\fR"
+If set, only flows that output to \fIport\fR are monitored.
+.IP "\fIfield\fB=\fIvalue\fR"
+Monitors only flows that have \fIfield\fR specified as the given
+\fIvalue\fR. Any syntax valid for matching on \fBdump\-flows\fR may
+be used.
+.RE
.IP
-
This command may be useful for debugging switch or controller
-implementations.
+implementations. With \fBwatch:\fR, it is particularly useful for
+observing how a controller updates flow tables.
.
.SS "OpenFlow Switch and Controller Commands"
.
pairs of hexadecimal digits delimited by colons
(e.g. \fB00:0A:E4:25:6B:B0\fR).
.
-.IP \fBdl_dst=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB/\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+.IP \fBdl_src=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB/\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+.IQ \fBdl_dst=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB/\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
Matches an Ethernet destination address specified as 6 pairs of
hexadecimal digits delimited by colons (e.g. \fB00:0A:E4:25:6B:B0\fR),
-with a wildcard mask following the slash. Only
-the following masks are allowed:
+with a wildcard mask following the slash. Open vSwitch 1.8 and later
+support arbitrary masks for source and/or destination. Earlier
+versions only support masking the destination with the following masks:
.RS
.IP \fB01:00:00:00:00:00\fR
Match only the multicast bit. Thus,
\fInetmask\fR allows restricting a match to an IPv4 address prefix.
The netmask may be specified as a dotted quad
(e.g. \fB192.168.1.0/255.255.255.0\fR) or as a CIDR block
-(e.g. \fB192.168.1.0/24\fR).
+(e.g. \fB192.168.1.0/24\fR). Open vSwitch 1.8 and later support
+arbitrary dotted quad masks; earlier versions support only CIDR masks,
+that is, the dotted quads that are equivalent to some CIDR block.
.IP
When \fBdl_type=0x0806\fR or \fBarp\fR is specified, matches the
\fBar_spa\fR or \fBar_tpa\fR field, respectively, in ARP packets for
extension to OpenFlow, which as of this writing is only known to be
implemented by Open vSwitch.
.
+.IP \fBmetadata=\fIvalue\fR[\fB/\fImask\fR]
+Matches \fIvalue\fR either exactly or with optional \fImask\fR in the metadata
+field. \fIvalue\fR and \fImask\fR are 64-bit integers, by default in decimal
+(use a \fB0x\fR prefix to specify hexadecimal). Arbitrary \fImask\fR values
+are allowed: a 1-bit in \fImask\fR indicates that the corresponding bit in
+\fIvalue\fR must match exactly, and a 0-bit wildcards that bit. Matching on
+metadata was added in Open vSwitch 1.8.
+.
.PP
The following shorthand notations are also available:
.
address. A single instance of \fB::\fR may be used to indicate multiple
groups of 16-bits of zeros. The optional \fInetmask\fR allows
restricting a match to an IPv6 address prefix. A netmask is specified
-as a CIDR block (e.g. \fB2001:db8:3c4d:1::/64\fR).
+as an IPv6 address (e.g. \fB2001:db8:3c4d:1::/ffff:ffff:ffff:ffff::\fR)
+or a CIDR block (e.g. \fB2001:db8:3c4d:1::/64\fR). Open vSwitch 1.8
+and later support arbitrary masks; earlier versions support only CIDR
+masks, that is, CIDR block and IPv6 addresses that are equivalent to
+CIDR blocks.
.
.IP \fBipv6_label=\fIlabel\fR
When \fBdl_type\fR is 0x86dd (possibly via shorthand, e.g., \fBipv6\fR
or \fBtcp6\fR), matches IPv6 flow label \fIlabel\fR.
.
-.IP \fBnd_target=\fIipv6\fR
+.IP \fBnd_target=\fIipv6\fR[\fB/\fInetmask\fR]
When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify
IPv6 Neighbor Discovery (ICMPv6 type 135 or 136), matches the target address
\fIipv6\fR. \fIipv6\fR is in the same format described earlier for the
.IP \fBtun_id=\fItunnel-id\fR[\fB/\fImask\fR]
Matches tunnel identifier \fItunnel-id\fR. Only packets that arrive
over a tunnel that carries a key (e.g. GRE with the RFC 2890 key
-extension) will have a nonzero tunnel ID. If \fImask\fR is omitted,
-\fItunnel-id\fR is the exact tunnel ID to match; if \fImask\fR is
-specified, then a 1-bit in \fImask\fR indicates that the corresponding
-bit in \fItunnel-id\fR must match exactly, and a 0-bit wildcards that
-bit.
-.IP
-In an attempt to be compatible with more switches, \fBovs\-ofctl\fR will
-prefer to use the ``tunnel ID from cookie'' Nicira extension to NXM.
-The use of this extension comes with three caveats: the top 32 bits of
-the \fBcookie\fR (see below) are used for \fItunnel-id\fR and thus
-unavailable for other use, specifying \fBtun_id\fR on \fBdump\-flows\fR
-or \fBdump\-aggregate\fR has no effect, and \fImask\fR is not supported.
-If any of these caveats apply, \fBovs-ofctl\fR will use NXM.
+extension and a nonzero key value) will have a nonzero tunnel ID.
+If \fImask\fR is omitted, \fItunnel-id\fR is the exact tunnel ID to match;
+if \fImask\fR is specified, then a 1-bit in \fImask\fR indicates that the
+corresponding bit in \fItunnel-id\fR must match exactly, and a 0-bit
+wildcards that bit.
.
.IP "\fBreg\fIidx\fB=\fIvalue\fR[\fB/\fImask\fR]"
Matches \fIvalue\fR either exactly or with optional \fImask\fR in
Outputs the packet on all switch physical ports other than the port on
which it was received.
.
-.IP \fBcontroller\fR:\fImax_len\fR
+.IP \fBcontroller(\fIkey\fB=\fIvalue\fR...\fB)
Sends the packet to the OpenFlow controller as a ``packet in''
-message. If \fImax_len\fR is a number, then it specifies the maximum
-number of bytes that should be sent. If \fImax_len\fR is \fBALL\fR or
-omitted, then the entire packet is sent.
+message. The supported key-value pairs are:
+.RS
+.IP "\fBmax_len=\fInbytes\fR"
+Limit to \fInbytes\fR the number of bytes of the packet to send to
+the controller. By default the entire packet is sent.
+.IP "\fBreason=\fIreason\fR"
+Specify \fIreason\fR as the reason for sending the message in the
+``packet in'' message. The supported reasons are \fBaction\fR (the
+default), \fBno_match\fR, and \fBinvalid_ttl\fR.
+.IP "\fBid=\fIcontroller-id\fR"
+Specify \fIcontroller-id\fR, a 16-bit integer, as the connection ID of
+the OpenFlow controller or controllers to which the ``packet in''
+message should be sent. The default is zero. Zero is also the
+default connection ID for each controller connection, and a given
+controller connection will only have a nonzero connection ID if its
+controller uses the \fBNXT_SET_CONTROLLER_ID\fR Nicira extension to
+OpenFlow.
+.RE
+Any \fIreason\fR other than \fBaction\fR and any nonzero
+\fIcontroller-id\fR uses a Nicira vendor extension that, as of this
+writing, is only known to be implemented by Open vSwitch (version 1.6
+or later).
+.
+.IP \fBcontroller\fR
+.IQ \fBcontroller\fR[\fB:\fInbytes\fR]
+Shorthand for \fBcontroller()\fR or
+\fBcontroller(max_len=\fInbytes\fB)\fR, respectively.
.
.IP \fBlocal\fR
Outputs the packet on the ``local port,'' which corresponds to the
actions were applied.
.
.IP \fBdec_ttl\fR
+.IQ \fBdec_ttl\fB[\fR(\fIid1,id2\fI)\fR]\fR
Decrement TTL of IPv4 packet or hop limit of IPv6 packet. If the
TTL or hop limit is initially zero, no decrement occurs. Instead,
a ``packet-in'' message with reason code \fBOFPR_INVALID_TTL\fR is
sent to each connected controller that has enabled receiving them,
-if any. Processing the current set of actions then stops.
-However, if the current set of actions was reached through
-``resubmit'' then remaining actions in outer levels resume
-processing.
+if any. Processing the current set of actions then stops. However,
+if the current set of actions was reached through ``resubmit'' then
+remaining actions in outer levels resume processing. This action
+also optionally supports the ability to specify a list of valid
+controller ids. Each of controllers in the list will receive the
+``packet_in'' message only if they have registered to receive the
+invalid ttl packets. If controller ids are not specified, the
+``packet_in'' message will be sent only to the controllers having
+controller id zero which have registered for the invalid ttl packets.
.
.IP \fBnote:\fR[\fIhh\fR]...
Does nothing at all. Any number of bytes represented as hex digits
\fIhh\fR may be included. Pairs of hex digits may be separated by
periods for readability.
+The \fBnote\fR action's format doesn't include an exact length for its
+payload, so the provided bytes will be padded on the right by enough
+bytes with value 0 to make the total number 6 more than a multiple of
+8.
.
.IP "\fBmove:\fIsrc\fB[\fIstart\fB..\fIend\fB]\->\fIdst\fB[\fIstart\fB..\fIend\fB]\fR"
Copies the named bits from field \fIsrc\fR to field \fIdst\fR.
Refer to \fBnicira\-ext.h\fR for more details.
.
.IP "\fBautopath(\fIid\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR"
+Deprecated and slated for removal in Feburary 2013.
+.IP
Given \fIid\fR, chooses an OpenFlow port and populates it in
\fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM field as
described above.
These key-value pairs have the same meaning as in the usual
\fBovs\-ofctl\fR flow syntax.
.
+.IP \fBfin_idle_timeout=\fIseconds\fR
+.IQ \fBfin_hard_timeout=\fIseconds\fR
+Adds a \fBfin_timeout\fR action with the specified arguments to the
+new flow. This feature was added in Open vSwitch 1.5.90.
+.
.IP \fBtable=\fInumber\fR
The table in which the new flow should be inserted. Specify a decimal
number between 0 and 254. The default, if \fBtable\fR is unspecified,
possibly for a lowest-priority ``catch-all'' flow, that is, a flow
with no match criteria. (This is why the default \fBtable\fR is 1, to
keep the learned flows separate from the primary flow table 0.)
-.RE
.
+.IP "\fBfin_timeout(\fIargument\fR[\fB,\fIargument\fR]\fB)"
+This action changes the idle timeout or hard timeout, or both, of this
+OpenFlow rule when the rule matches a TCP packet with the FIN or RST
+flag. When such a packet is observed, the action reduces the rule's
+timeouts to those specified on the action. If the rule's existing
+timeout is already shorter than the one that the action specifies,
+then that timeout is unaffected.
+.IP
+\fIargument\fR takes the following forms:
+.RS
+.IP "\fBidle_timeout=\fIseconds\fR"
+Causes the flow to expire after the given number of seconds of
+inactivity.
+.
+.IP "\fBhard_timeout=\fIseconds\fR"
+Causes the flow to expire after the given number of seconds,
+regardless of activity. (\fIseconds\fR specifies time since the
+flow's creation, not since the receipt of the FIN or RST.)
+.RE
+.IP
+This action was added in Open vSwitch 1.5.90.
.IP "\fBexit\fR"
This action causes Open vSwitch to immediately halt execution of further
actions. Those actions which have already been executed are unaffected. Any
further actions, including those which may be in other tables, or different
levels of the \fBresubmit\fR call stack, are ignored.
+.RE
.
.PP
An opaque identifier called a cookie can be used as a handle to identify
a set of flows:
.
-.IP \fBcookie=\fIvalue\fR[\fB/\fImask\fR]
+.IP \fBcookie=\fIvalue\fR
+.
+A cookie can be associated with a flow using the \fBadd\-flow\fR,
+\fBadd\-flows\fR, and \fBmod\-flows\fR commands. \fIvalue\fR can be any
+64-bit number and need not be unique among flows. If this field is
+omitted, a default cookie value of 0 is used.
+.
+.IP \fBcookie=\fIvalue\fR\fB/\fImask\fR
.
-A cookie can be associated with a flow using the \fBadd-flow\fR and
-\fBadd-flows\fR commands. \fIvalue\fR can be any 64-bit number and need
-not be unique among flows. If this field is omitted, a default cookie
-value of 0 is used.
-.IP
When using NXM, the cookie can be used as a handle for querying,
-modifying, and deleting flows. In addition to \fIvalue\fR, an optional
-\fImask\fR may be supplied for the \fBdel-flows\fR, \fBmod-flows\fR,
-\fBdump-flows\fR, and \fBdump-aggregate\fR commands to limit matching
-cookies. A 1-bit in \fImask\fR indicates that the corresponding bit in
-\fIcookie\fR must match exactly, and a 0-bit wildcards that bit.
+modifying, and deleting flows. \fIvalue\fR and \fImask\fR may be
+supplied for the \fBdel\-flows\fR, \fBmod\-flows\fR, \fBdump\-flows\fR, and
+\fBdump\-aggregate\fR commands to limit matching cookies. A 1-bit in
+\fImask\fR indicates that the corresponding bit in \fIcookie\fR must
+match exactly, and a 0-bit wildcards that bit. A mask of \-1 may be used
+to exactly match a cookie.
+.IP
+The \fBmod\-flows\fR command can update the cookies of flows that
+match a cookie by specifying the \fIcookie\fR field twice (once with a
+mask for matching and once without to indicate the new value):
+.RS
+.IP "\fBovs\-ofctl mod\-flows br0 cookie=1,actions=normal\fR"
+Change all flows' cookies to 1 and change their actions to \fBnormal\fR.
+.IP "\fBovs\-ofctl mod\-flows br0 cookie=1/\-1,cookie=2,actions=normal\fR"
+Update cookies with a value of 1 to 2 and change their actions to
+\fBnormal\fR.
+.RE
+.IP
+The ability to match on cookies was added in Open vSwitch 1.5.0.
.
.PP
The following additional field sets the priority for flows added by
the \fBadd\-flow\fR and \fBadd\-flows\fR commands. For
\fBmod\-flows\fR and \fBdel\-flows\fR when \fB\-\-strict\fR is
specified, priority must match along with the rest of the flow
-specification. For \fBmod\-flows\fR without \fB\-\-strict\fR,
+specification. For \fBmod-flows\fR without \fB\-\-strict\fR,
priority is only significant if the command creates a new flow, that
is, non-strict \fBmod\-flows\fR does not match on priority and will
not change the priority of existing flows. Other commands do not
have priority over an entry containing wildcards, so it has an implicit
priority value of 65535. When adding a flow, if the field is not specified,
the flow's priority will default to 32768.
+.IP
+OpenFlow leaves behavior undefined when two or more flows with the
+same priority can match a single packet. Some users expect
+``sensible'' behavior, such as more specific flows taking precedence
+over less specific flows, but OpenFlow does not specify this and Open
+vSwitch does not implement it. Users should therefore take care to
+use priorities to ensure the behavior that they expect.
.
.PP
The \fBadd\-flow\fR, \fBadd\-flows\fR, and \fBmod\-flows\fR commands
\fB\-\-strict\fR
Uses strict matching when running flow modification commands.
.
-.IP "\fB\-F \fIformat\fR"
-.IQ "\fB\-\-flow\-format=\fIformat\fR"
-\fBovs\-ofctl\fR supports the following flow formats, in order of
-increasing capability:
+.IP "\fB\-F \fIformat\fR[\fB,\fIformat\fR...]"
+.IQ "\fB\-\-flow\-format=\fIformat\fR[\fB,\fIformat\fR...]"
+\fBovs\-ofctl\fR supports the following individual flow formats, any
+number of which may be listed as \fIformat\fR:
.RS
-.IP "\fBopenflow10\fR"
-This is the standard OpenFlow 1.0 flow format. It should be supported
-by all OpenFlow switches.
+.IP "\fBOpenFlow10\-table_id\fR"
+This is the standard OpenFlow 1.0 flow format. All OpenFlow switches
+and all versions of Open vSwitch support this flow format.
.
-.IP "\fBnxm\fR (Nicira Extended Match)"
+.IP "\fBOpenFlow10+table_id\fR"
+This is the standard OpenFlow 1.0 flow format plus a Nicira extension
+that allows \fBovs\-ofctl\fR to specify the flow table in which a
+particular flow should be placed. Open vSwitch 1.2 and later supports
+this flow format.
+.
+.IP "\fBNXM\-table_id\fR (Nicira Extended Match)"
This Nicira extension to OpenFlow is flexible and extensible. It
supports all of the Nicira flow extensions, such as \fBtun_id\fR and
-registers.
+registers. Open vSwitch 1.1 and later supports this flow format.
+.
+.IP "\fBNXM+table_id\fR (Nicira Extended Match)"
+This combines Nicira Extended match with the ability to place a flow
+in a specific table. Open vSwitch 1.2 and later supports this flow
+format.
.RE
+.
.IP
-Usually, \fBovs\-ofctl\fR picks the correct format automatically. For
-commands that modify the flow table, \fBovs\-ofctl\fR by default uses
-the most widely supported flow format that supports the flows being
-added. For commands that query the flow table, \fBovs\-ofctl\fR by
-default queries and uses the most advanced format supported by the
-switch.
-.IP
-This option, where \fIformat\fR is one of the formats listed in the
-above table, overrides \fBovs\-ofctl\fR's default choice of flow
-format. If a command cannot work as requested using the requested
-flow format, \fBovs\-ofctl\fR will report a fatal error.
+\fBovs\-ofctl\fR also supports the following abbreviations for
+collections of flow formats:
+.RS
+.IP "\fBany\fR"
+Any supported flow format.
+.IP "\fBOpenFlow10\fR"
+\fBOpenFlow10\-table_id\fR or \fBOpenFlow10+table_id\fR.
+.IP "\fBNXM\fR"
+\fBNXM\-table_id\fR or \fBNXM+table_id\fR.
+.RE
.
+.IP
+For commands that modify the flow table, \fBovs\-ofctl\fR by default
+negotiates the most widely supported flow format that supports the
+flows being added. For commands that query the flow table,
+\fBovs\-ofctl\fR by default uses the most advanced format supported by
+the switch.
+.IP
+This option, where \fIformat\fR is a comma-separated list of one or
+more of the formats listed above, limits \fBovs\-ofctl\fR's choice of
+flow format. If a command cannot work as requested using one of the
+specified flow formats, \fBovs\-ofctl\fR will report a fatal error.
.
.IP "\fB\-P \fIformat\fR"
.IQ "\fB\-\-packet\-in\-format=\fIformat\fR"
requested format, \fBovs\-ofctl\fR will report a fatal error. This option only
affects the \fBmonitor\fR command.
.
+.IP "\fB\-\-timestamp\fR"
+Print a timestamp before each received packet. This option only
+affects the \fBmonitor\fR and \fBsnoop\fR commands.
+.
.IP "\fB\-m\fR"
.IQ "\fB\-\-more\fR"
Increases the verbosity of OpenFlow messages printed and logged by
\fBovs\-ofctl\fR commands. Specify this option more than once to
increase verbosity further.
.
+.IP \fB\-\-sort\fR[\fB=\fIfield\fR]
+.IQ \fB\-\-rsort\fR[\fB=\fIfield\fR]
+Display output sorted by flow \fIfield\fR in ascending
+(\fB\-\-sort\fR) or descending (\fB\-\-rsort\fR) order, where
+\fIfield\fR is any of the fields that are allowed for matching or
+\fBpriority\fR to sort by priority. When \fIfield\fR is omitted, the
+output is sorted by priority. Specify these options multiple times to
+sort by multiple fields.
+.IP
+Any given flow will not necessarily specify a value for a given
+field. This requires special treatement:
+.RS
+.IP \(bu
+A flow that does not specify any part of a field that is used for sorting is
+sorted after all the flows that do specify the field. For example,
+\fB\-\-sort=tcp_src\fR will sort all the flows that specify a TCP
+source port in ascending order, followed by the flows that do not
+specify a TCP source port at all.
+.IP \(bu
+A flow that only specifies some bits in a field is sorted as if the
+wildcarded bits were zero. For example, \fB\-\-sort=nw_src\fR would
+sort a flow that specifies \fBnw_src=192.168.0.0/24\fR the same as
+\fBnw_src=192.168.0.0\fR.
+.RE
+.IP
+These options currently affect only \fBdump\-flows\fR output.
+.
.ds DD \
\fBovs\-ofctl\fR detaches only when executing the \fBmonitor\fR or \
\fBsnoop\fR commands.
express an OpenFlow message, on the OpenFlow connection. This command
is useful only when executing the \fBmonitor\fR command.
.
+.IP "\fBofctl/barrier\fR"
+Sends an OpenFlow barrier request on the OpenFlow connection and waits
+for a reply. This command is useful only for the \fBmonitor\fR
+command.
+.
.SH EXAMPLES
.
The following examples assume that \fBovs\-vswitchd\fR has a bridge
git://git.onelab.eu / sliver-openvswitch.git / blobdiff