\fBar_spa\fR or \fBar_tpa\fR field, respectively, in ARP packets for
IPv4 and Ethernet.
.IP
-When \fBdl_type\fR is wildcarded or set to a value other than 0x0800
-or 0x0806, the values of \fBnw_src\fR and \fBnw_dst\fR are ignored
+When \fBdl_type=0x8035\fR or \fBrarp\fR is specified, matches the
+\fBar_spa\fR or \fBar_tpa\fR field, respectively, in RARP packets for
+IPv4 and Ethernet.
+.IP
+When \fBdl_type\fR is wildcarded or set to a value other than 0x0800,
+0x0806, or 0x8035, the values of \fBnw_src\fR and \fBnw_dst\fR are ignored
(see \fBFlow Syntax\fR above).
.
.IP \fBnw_proto=\fIproto\fR
8 bits of the ARP opcode. ARP opcodes greater than 255 are treated as
0.
.IP
+When \fBrarp\fR or \fBdl_type=0x8035\fR is specified, matches the lower
+8 bits of the ARP opcode. ARP opcodes greater than 255 are treated as
+0.
+.IP
When \fBdl_type\fR is wildcarded or set to a value other than 0x0800,
-0x0806, or 0x86dd, the value of \fBnw_proto\fR is ignored (see \fBFlow
-Syntax\fR above).
+0x0806, 0x8035 or 0x86dd, the value of \fBnw_proto\fR is ignored (see
+\fBFlow Syntax\fR above).
.
.IP \fBnw_tos=\fItos\fR
Matches IP ToS/DSCP or IPv6 traffic class field \fItos\fR, which is
.IP \fBarp\fR
Same as \fBdl_type=0x0806\fR.
.
+.IP \fBrarp\fR
+Same as \fBdl_type=0x8035\fR.
+.
.PP
The following field assignments require support for the NXM (Nicira
Extended Match) extension to OpenFlow. When one of these is specified,
.
.IP \fBarp_sha=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
.IQ \fBarp_tha=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
-When \fBdl_type\fR specifies ARP, \fBarp_sha\fR and \fBarp_tha\fR match
-the source and target hardware address, respectively. An address is
-specified as 6 pairs of hexadecimal digits delimited by colons.
+When \fBdl_type\fR specifies either ARP or RARP, \fBarp_sha\fR and
+\fBarp_tha\fR match the source and target hardware address, respectively. An
+address is specified as 6 pairs of hexadecimal digits delimited by colons.
.
.IP \fBipv6_src=\fIipv6\fR[\fB/\fInetmask\fR]
.IQ \fBipv6_dst=\fIipv6\fR[\fB/\fInetmask\fR]
.IP \fBstrip_vlan\fR
Strips the VLAN tag from a packet if it is present.
.
+.IP \fBpush_vlan\fR:\fIethertype\fR
+Push a new VLAN tag onto the packet. Ethertype is used as the the Ethertype
+for the tag. Only ethertype 0x8100 should be used. (0x88a8 which the spec
+allows isn't supported at the moment.)
+A priority of zero and the tag of zero are used for the new tag.
+.
.IP \fBmod_dl_src\fB:\fImac\fR
Sets the source Ethernet address to \fImac\fR.
.
Sets the IPv4 ToS/DSCP field to \fItos\fR. Valid values are between 0 and
255, inclusive. Note that the two lower reserved bits are never
modified.
-.
.RE
.IP
The following actions are Nicira vendor extensions that, as of this writing, are
Example: \fBload:55\->NXM_NX_REG2[0..5]\fR loads value 55 (bit pattern
\fB110111\fR) into bits 0 through 5, inclusive, in register 2.
.
+.IP "\fBset_field:\fIvalue\fB\->\fIdst"
+Writes the literal \fIvalue\fR into the field \fIdst\fR, which should
+be specified as a name used for matching. (This is similar to
+\fBload\fR but more closely matches the set-field action defined in
+Open Flow 1.2 and above.)
+.
+.IP
+Example: \fBset_field:fe80:0123:4567:890a:a6ba:dbff:fefe:59fa\->ipv6_src\fR
+.
.IP "\fBmultipath(\fIfields\fB, \fIbasis\fB, \fIalgorithm\fB, \fIn_links\fB, \fIarg\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR"
Hashes \fIfields\fR using \fIbasis\fR as a universal hash parameter,
then the applies multipath link selection \fIalgorithm\fR (with
with no match criteria. (This is why the default \fBtable\fR is 1, to
keep the learned flows separate from the primary flow table 0.)
.
+.RS
+.IP \fBapply_actions(\fR[\fIaction\fR][\fB,\fIaction\fR...]\fB)
+Applies the specific action(s) immediately. The syntax of actions are same
+to \fBactions=\fR field.
+.
+.IP \fBclear_actions\fR
+Clears all the actions in the action set immediately.
+.
+.IP \fBwrite_metadata\fB:\fIvalue\fR[/\fImask\fR]
+Updates the metadata field for the flow. If \fImask\fR is omitted, the
+metadata field is set exactly to \fIvalue\fR; if \fImask\fR is specified, then
+a 1-bit in \fImask\fR indicates that the corresponding bit in the metadata
+field will be replaced with the corresponding bit from \fIvalue\fR. Both
+\fIvalue\fR and \fImask\fR are 64-bit values that are decimal by default; use
+a \fB0x\fR prefix to specify them in hexadecimal.
+.
+.IP \fBgoto_table\fR:\fItable\fR
+Indicates the next table in the process pipeline.
+.RE
+.
.IP "\fBfin_timeout(\fIargument\fR[\fB,\fIargument\fR]\fB)"
This action changes the idle timeout or hard timeout, or both, of this
OpenFlow rule when the rule matches a TCP packet with the FIN or RST
\fB\-\-strict\fR
Uses strict matching when running flow modification commands.
.
+.so lib/ofp-version.man
+.
.IP "\fB\-F \fIformat\fR[\fB,\fIformat\fR...]"
.IQ "\fB\-\-flow\-format=\fIformat\fR[\fB,\fIformat\fR...]"
\fBovs\-ofctl\fR supports the following individual flow formats, any
git://git.onelab.eu / sliver-openvswitch.git / blobdiff