. ns
. IP "\\$1"
..
-.TH ovs\-ofctl 8 "January 2010" "Open vSwitch" "Open vSwitch Manual"
+.TH ovs\-ofctl 8 "January 2011" "Open vSwitch" "Open vSwitch Manual"
.ds PN ovs\-ofctl
.
.SH NAME
information on its flow tables and ports.
.
.TP
-\fBstatus \fIswitch\fR [\fIkey\fR]
-Prints to the console a series of key-value pairs that report the
-status of \fIswitch\fR. If \fIkey\fR is specified, only the key-value
-pairs whose key names begin with \fIkey\fR are printed. If \fIkey\fR is
-omitted, all key-value pairs are printed.
-.
-.TP
-\fBdump-tables \fIswitch\fR
+\fBdump\-tables \fIswitch\fR
Prints to the console statistics for each of the flow tables used by
\fIswitch\fR.
.
.TP
-\fBdump-ports \fIswitch\fR [\fInetdev\fR]
+\fBdump\-ports \fIswitch\fR [\fInetdev\fR]
Prints to the console statistics for network devices associated with
\fIswitch\fR. If \fInetdev\fR is specified, only the statistics
associated with that device will be printed. \fInetdev\fR can be an
OpenFlow assigned port number or device name, e.g. \fBeth0\fR.
.
.TP
-\fBmod-port \fIswitch\fR \fInetdev\fR \fIaction\fR
+\fBdump\-ports\-desc \fIswitch\fR
+Prints to the console detailed information about network devices
+associated with \fIswitch\fR (version 1.7 or later). This is a subset
+of the information provided by the \fBshow\fR command.
+.
+.TP
+\fBmod\-port \fIswitch\fR \fInetdev\fR \fIaction\fR
Modify characteristics of an interface monitored by \fIswitch\fR.
\fInetdev\fR can be referred to by its OpenFlow assigned port number or
the device name, e.g. \fBeth0\fR. The \fIaction\fR may be any one of the
following:
.
.RS
-.IP \fBup\fR
-Enables the interface. This is equivalent to ``ifconfig up'' on a Unix
-system.
-.
-.IP \fBdown\fR
-Disables the interface. This is equivalent to ``ifconfig down'' on a Unix
-system.
+.IQ \fBup\fR
+.IQ \fBdown\fR
+Enable or disable the interface. This is equivalent to \fBifconfig
+up\fR or \fBifconfig down\fR on a Unix system.
+.
+.IP \fBstp\fR
+.IQ \fBno\-stp\fR
+Enable or disable 802.1D spanning tree protocol (STP) on the
+interface. OpenFlow implementations that don't support STP will
+refuse to enable it.
+.
+.IP \fBreceive\fR
+.IQ \fBno\-receive\fR
+.IQ \fBreceive\-stp\fR
+.IQ \fBno\-receive\-stp\fR
+Enable or disable OpenFlow processing of packets received on this
+interface. When packet processing is disabled, packets will be
+dropped instead of being processed through the OpenFlow table. The
+\fBreceive\fR or \fBno\-receive\fR setting applies to all packets
+except 802.1D spanning tree packets, which are separately controlled
+by \fBreceive\-stp\fR or \fBno\-receive\-stp\fR.
+.
+.IP \fBforward\fR
+.IQ \fBno\-forward\fR
+Allow or disallow forwarding of traffic to this interface. By
+default, forwarding is enabled.
.
.IP \fBflood\fR
-When a \fIflood\fR action is specified, traffic will be sent out this
-interface. This is the default posture for monitored ports.
+.IQ \fBno\-flood\fR
+Controls whether an OpenFlow \fBflood\fR action will send traffic out
+this interface. By default, flooding is enabled. Disabling flooding
+is primarily useful to prevent loops when a spanning tree protocol is
+not in use.
+.
+.IP \fBpacket\-in\fR
+.IQ \fBno\-packet\-in\fR
+Controls whether packets received on this interface that do not match
+a flow table entry generate a ``packet in'' message to the OpenFlow
+controller. By default, ``packet in'' messages are enabled.
+.RE
+.IP
+The \fBshow\fR command displays (among other information) the
+configuration that \fBmod\-port\fR changes.
.
-.IP \fBnoflood\fR
-When a \fIflood\fR action is specified, traffic will not be sent out
-this interface. This is primarily useful to prevent loops when a
-spanning tree protocol is not in use.
+.IP "\fBget\-frags \fIswitch\fR"
+Prints \fIswitch\fR's fragment handling mode. See \fBset\-frags\fR,
+below, for a description of each fragment handling mode.
+.IP
+The \fBshow\fR command also prints the fragment handling mode among
+its other output.
.
+.IP "\fBset\-frags \fIswitch frag_mode\fR"
+Configures \fIswitch\fR's treatment of IPv4 and IPv6 fragments. The
+choices for \fIfrag_mode\fR are:
+.RS
+.IP "\fBnormal\fR"
+Fragments pass through the flow table like non-fragmented packets.
+The TCP ports, UDP ports, and ICMP type and code fields are always set
+to 0, even for fragments where that information would otherwise be
+available (fragments with offset 0). This is the default fragment
+handling mode for an OpenFlow switch.
+.IP "\fBdrop\fR"
+Fragments are dropped without passing through the flow table.
+.IP "\fBreassemble\fR"
+The switch reassembles fragments into full IP packets before passing
+them through the flow table. Open vSwitch does not implement this
+fragment handling mode.
+.IP "\fBnx\-match\fR"
+Fragments pass through the flow table like non-fragmented packets.
+The TCP ports, UDP ports, and ICMP type and code fields are available
+for matching for fragments with offset 0, and set to 0 in fragments
+with nonzero offset. This mode is a Nicira extension.
.RE
+.IP
+See the description of \fBip_frag\fR, below, for a way to match on
+whether a packet is a fragment and on its fragment offset.
.
.TP
-\fBdump-flows \fIswitch \fR[\fIflows\fR]
+\fBdump\-flows \fIswitch \fR[\fIflows\fR]
Prints to the console all flow entries in \fIswitch\fR's
tables that match \fIflows\fR. If \fIflows\fR is omitted, all flows
in the switch are retrieved. See \fBFlow Syntax\fR, below, for the
\fBTable Entry Output\fR.
.
.TP
-\fBdump-aggregate \fIswitch \fR[\fIflows\fR]
+\fBdump\-aggregate \fIswitch \fR[\fIflows\fR]
Prints to the console aggregate statistics for flows in
\fIswitch\fR's tables that match \fIflows\fR. If \fIflows\fR is omitted,
the statistics are aggregated across all flows in the switch's flow
tables. See \fBFlow Syntax\fR, below, for the syntax of \fIflows\fR.
-The output format is descrbed in \fBTable Entry Output\fR.
+The output format is described in \fBTable Entry Output\fR.
+.
+.IP "\fBqueue\-stats \fIswitch \fR[\fIport \fR[\fIqueue\fR]]"
+Prints to the console statistics for the specified \fIqueue\fR on
+\fIport\fR within \fIswitch\fR. Either of \fIport\fR or \fIqueue\fR
+or both may be omitted (or equivalently specified as \fBALL\fR). If
+both are omitted, statistics are printed for all queues on all ports.
+If only \fIqueue\fR is omitted, then statistics are printed for all
+queues on \fIport\fR; if only \fIport\fR is omitted, then statistics
+are printed for \fIqueue\fR on every port where it exists.
+.
+.SS "OpenFlow Switch Flow Table Commands"
+.
+These commands manage the flow table in an OpenFlow switch. In each
+case, \fIflow\fR specifies a flow entry in the format described in
+\fBFlow Syntax\fR, below, and \fIfile\fR is a text file that contains
+zero or more flows in the same syntax, one per line.
+.
+.IP "\fBadd\-flow \fIswitch flow\fR"
+.IQ "\fBadd\-flow \fIswitch \fB\- < \fIfile\fR"
+.IQ "\fBadd\-flows \fIswitch file\fR"
+Add each flow entry to \fIswitch\fR's tables.
+.
+.IP "[\fB\-\-strict\fR] \fBmod\-flows \fIswitch flow\fR"
+.IQ "[\fB\-\-strict\fR] \fBmod\-flows \fIswitch \fB\- < \fIfile\fR"
+Modify the actions in entries from \fIswitch\fR's tables that match
+the specified flows. With \fB\-\-strict\fR, wildcards are not treated
+as active for matching purposes.
+.
+.IP "\fBdel\-flows \fIswitch\fR"
+.IQ "[\fB\-\-strict\fR] \fBdel\-flows \fIswitch \fR[\fIflow\fR]"
+.IQ "[\fB\-\-strict\fR] \fBdel\-flows \fIswitch \fB\- < \fIfile\fR"
+Deletes entries from \fIswitch\fR's flow table. With only a
+\fIswitch\fR argument, deletes all flows. Otherwise, deletes flow
+entries that match the specified flows. With \fB\-\-strict\fR,
+wildcards are not treated as active for matching purposes.
+.
+.IP "[\fB\-\-readd\fR] \fBreplace\-flows \fIswitch file\fR"
+Reads flow entries from \fIfile\fR (or \fBstdin\fR if \fIfile\fR is
+\fB\-\fR) and queries the flow table from \fIswitch\fR. Then it fixes
+up any differences, adding flows from \fIflow\fR that are missing on
+\fIswitch\fR, deleting flows from \fIswitch\fR that are not in
+\fIfile\fR, and updating flows in \fIswitch\fR whose actions, cookie,
+or timeouts differ in \fIfile\fR.
.
-.TP
-\fBadd-flow \fIswitch flow\fR
-Add the flow entry as described by \fIflow\fR to the \fIswitch\fR's
-tables. The flow entry is in the format described in \fBFlow Syntax\fR,
-below.
-.
-.TP
-\fBadd-flows \fIswitch file\fR
-Add flow entries as described in \fIfile\fR to \fIswitch\fR's
-tables. Each line in \fIfile\fR is a flow entry in the format
-described in \fBFlow Syntax\fR, below.
-.
-.TP
-\fBmod-flows \fIswitch flow\fR
-Modify the actions in entries from the \fIswitch\fR's tables
-that match \fIflow\fR. When invoked with the \fB--strict\fR option,
-wildcards are not treated as active for matching purposes. See
-\fBFlow Syntax\fR, below, for the syntax of \fIflows\fR.
-.
-.TP
-\fBdel-flows \fIswitch \fR[\fIflow\fR]
-Deletes entries from the \fIswitch\fR's tables that match
-\fIflow\fR. When invoked with the \fB--strict\fR option, wildcards are
-not treated as active for matching purposes. If \fIflow\fR is
-omitted and the \fB--strict\fR option is not used, all flows in the
-switch's tables are removed. See \fBFlow Syntax\fR, below, for the
-syntax of \fIflows\fR.
+.IP
+With \fB\-\-readd\fR, \fBovs\-ofctl\fR adds all the flows from
+\fIfile\fR, even those that exist with the same actions, cookie, and
+timeout in \fIswitch\fR. This resets all the flow packet and byte
+counters to 0, which can be useful for debugging.
+.
+.IP "\fBdiff\-flows \fIsource1 source2\fR"
+Reads flow entries from \fIsource1\fR and \fIsource2\fR and prints the
+differences. A flow that is in \fIsource1\fR but not in \fIsource2\fR
+is printed preceded by a \fB\-\fR, and a flow that is in \fIsource2\fR
+but not in \fIsource1\fR is printed preceded by a \fB+\fR. If a flow
+exists in both \fIsource1\fR and \fIsource2\fR with different actions,
+cookie, or timeouts, then both versions are printed preceded by
+\fB\-\fR and \fB+\fR, respectively.
+.IP
+\fIsource1\fR and \fIsource2\fR may each name a file or a switch. If
+a name begins with \fB/\fR or \fB.\fR, then it is considered to be a
+file name. A name that contains \fB:\fR is considered to be a switch.
+Otherwise, it is a file if a file by that name exists, a switch if
+not.
+.IP
+For this command, an exit status of 0 means that no differences were
+found, 1 means that an error occurred, and 2 means that some
+differences were found.
+.
+.IP "\fBpacket\-out \fIswitch in_port actions packet\fR..."
+Connects to \fIswitch\fR and instructs it to execute the OpenFlow
+\fIactions\fR on each \fIpacket\fR. For the purpose of executing the
+actions, the packets are considered to have arrived on \fIin_port\fR,
+which may be an OpenFlow assigned port number, an OpenFlow port name
+(e.g. \fBeth0\fR), the keyword \fBlocal\fR for the OpenFlow ``local''
+port \fBOFPP_LOCAL\fR, or the keyword \fBnone\fR to indicate that the
+packet was generated by the switch itself.
+.
+.SS "OpenFlow Switch Monitoring Commands"
+.
+.IP "\fBsnoop \fIswitch\fR"
+Connects to \fIswitch\fR and prints to the console all OpenFlow
+messages received. Unlike other \fBovs\-ofctl\fR commands, if
+\fIswitch\fR is the name of a bridge, then the \fBsnoop\fR command
+connects to a Unix domain socket named
+\fB@RUNDIR@/\fIbridge\fB.snoop\fR. \fBovs\-vswitchd\fR listens on
+such a socket for each bridge and sends to it all of the OpenFlow
+messages sent to or received from its configured OpenFlow controller.
+Thus, this command can be used to view OpenFlow protocol activity
+between a switch and its controller.
+.IP
+When a switch has more than one controller configured, only the
+traffic to and from a single controller is output. If none of the
+controllers is configured as a master or a slave (using a Nicira
+extension to OpenFlow), then a controller is chosen arbitrarily among
+them. If there is a master controller, it is chosen; otherwise, if
+there are any controllers that are not masters or slaves, one is
+chosen arbitrarily; otherwise, a slave controller is chosen
+arbitrarily. This choice is made once at connection time and does not
+change as controllers reconfigure their roles.
+.IP
+If a switch has no controller configured, or if
+the configured controller is disconnected, no traffic is sent, so
+monitoring will not show any traffic.
.
-.TP
-\fBmonitor \fIswitch\fR [\fImiss-len\fR]
+.IP "\fBmonitor \fIswitch\fR [\fImiss-len\fR] [\fIinvalid_ttl\fR]"
Connects to \fIswitch\fR and prints to the console all OpenFlow
-messages received. Usually, \fIswitch\fR should specify a connection
-named on \fBovs\-openflowd\fR(8)'s \fB-l\fR or \fB--listen\fR command line
-option.
+messages received. Usually, \fIswitch\fR should specify the name of a
+bridge in the \fBovs\-vswitchd\fR database.
.IP
If \fImiss-len\fR is provided, \fBovs\-ofctl\fR sends an OpenFlow ``set
configuration'' message at connection setup time that requests
-\fImiss-len\fR bytes of each packet that misses the flow table. The
-OpenFlow reference implementation does not send these messages to the
+\fImiss-len\fR bytes of each packet that misses the flow table. Open vSwitch
+does not send these and other asynchronous messages to an
\fBovs\-ofctl monitor\fR client connection unless a nonzero value is
-specified on this argument.
+specified on this argument. (Thus, if \fImiss\-len\fR is not
+specified, very little traffic will ordinarily be printed.)
.IP
+.IP
+If \fBinvalid_ttl\fR is passed, \fBovs\-ofctl\fR sends an OpenFlow ``set
+configuration'' message at connection setup time that requests
+\fIINVALID_TTL_TO_CONTROLLER\fR, so that \fBovs\-ofctl monitor\fR can
+receive ``packets-in'' messages when TTL reaches zero on \fBdec_ttl\fR action.
+.IP
+
This command may be useful for debugging switch or controller
implementations.
.
.TP
\fBprobe \fItarget\fR
Sends a single OpenFlow echo-request message to \fItarget\fR and waits
-for the response. With the \fB-t\fR or \fB--timeout\fR option, this
+for the response. With the \fB\-t\fR or \fB\-\-timeout\fR option, this
command can test whether an OpenFlow switch or controller is up and
running.
.
quoting to prevent the shell from breaking the description into
multiple arguments.)
.PP
+Flow descriptions should be in \fBnormal form\fR. This means that a
+flow may only specify a value for an L3 field if it also specifies a
+particular L2 protocol, and that a flow may only specify an L4 field
+if it also specifies particular L2 and L3 protocol types. For
+example, if the L2 protocol type \fBdl_type\fR is wildcarded, then L3
+fields \fBnw_src\fR, \fBnw_dst\fR, and \fBnw_proto\fR must also be
+wildcarded. Similarly, if \fBdl_type\fR or \fBnw_proto\fR (the L3
+protocol type) is wildcarded, so must be \fBtp_dst\fR and
+\fBtp_src\fR, which are L4 fields. \fBovs\-ofctl\fR will warn about
+flows not in normal form.
+.PP
The following field assignments describe how a flow matches a packet.
If any of these assignments is omitted from the flow syntax, the field
is treated as a wildcard; thus, if all of them are omitted, the
(\fB*\fR should be quoted to protect it from shell expansion.)
.
.IP \fBin_port=\fIport_no\fR
-Matches physical port \fIport_no\fR. Switch ports are numbered as
+Matches OpenFlow port \fIport_no\fR. Ports are numbered as
displayed by \fBovs\-ofctl show\fR.
+.IP
+(The \fBresubmit\fR action can search OpenFlow flow tables with
+arbitrary \fBin_port\fR values, so flows that match port numbers that
+do not exist from an OpenFlow perspective can still potentially be
+matched.)
.
.IP \fBdl_vlan=\fIvlan\fR
Matches IEEE 802.1q Virtual LAN tag \fIvlan\fR. Specify \fB0xffff\fR
pairs of hexadecimal digits delimited by colons
(e.g. \fB00:0A:E4:25:6B:B0\fR).
.
+.IP \fBdl_dst=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB/\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+Matches an Ethernet destination address specified as 6 pairs of
+hexadecimal digits delimited by colons (e.g. \fB00:0A:E4:25:6B:B0\fR),
+with a wildcard mask following the slash. Only
+the following masks are allowed:
+.RS
+.IP \fB01:00:00:00:00:00\fR
+Match only the multicast bit. Thus,
+\fBdl_dst=01:00:00:00:00:00/01:00:00:00:00:00\fR matches all multicast
+(including broadcast) Ethernet packets, and
+\fBdl_dst=00:00:00:00:00:00/01:00:00:00:00:00\fR matches all unicast
+Ethernet packets.
+.IP \fBfe:ff:ff:ff:ff:ff\fR
+Match all bits except the multicast bit. This is probably not useful.
+.IP \fBff:ff:ff:ff:ff:ff\fR
+Exact match (equivalent to omitting the mask).
+.IP \fB00:00:00:00:00:00\fR
+Wildcard all bits (equivalent to \fBdl_dst=*\fR.)
+.RE
+.
.IP \fBdl_type=\fIethertype\fR
Matches Ethernet protocol type \fIethertype\fR, which is specified as an
integer between 0 and 65535, inclusive, either in decimal or as a
IPv4 and Ethernet.
.IP
When \fBdl_type\fR is wildcarded or set to a value other than 0x0800
-or 0x0806, the values of \fBnw_src\fR and \fBnw_dst\fR are silently
-ignored.
+or 0x0806, the values of \fBnw_src\fR and \fBnw_dst\fR are ignored
+(see \fBFlow Syntax\fR above).
.
.IP \fBnw_proto=\fIproto\fR
When \fBip\fR or \fBdl_type=0x0800\fR is specified, matches IP
protocol type \fIproto\fR, which is specified as a decimal number
-between 0 and 255, inclusive (e.g. 6 to match TCP packets).
+between 0 and 255, inclusive (e.g. 1 to match ICMP packets or 6 to match
+TCP packets).
+.IP
+When \fBipv6\fR or \fBdl_type=0x86dd\fR is specified, matches IPv6
+header type \fIproto\fR, which is specified as a decimal number between
+0 and 255, inclusive (e.g. 58 to match ICMPv6 packets or 6 to match
+TCP). The header type is the terminal header as described in the
+\fBDESIGN\fR document.
.IP
When \fBarp\fR or \fBdl_type=0x0806\fR is specified, matches the lower
8 bits of the ARP opcode. ARP opcodes greater than 255 are treated as
0.
.IP
-When \fBdl_type\fR is wildcarded or set to a value other than 0x0800
-or 0x0806, the value of \fBnw_proto\fR is silently ignored.
+When \fBdl_type\fR is wildcarded or set to a value other than 0x0800,
+0x0806, or 0x86dd, the value of \fBnw_proto\fR is ignored (see \fBFlow
+Syntax\fR above).
.
.IP \fBnw_tos=\fItos\fR
-Matches IP ToS/DSCP field \fItos\fR, which is specified as a decimal
-number between 0 and 255, inclusive. Note that the two lower reserved
-bits are ignored for matching purposes.
+Matches IP ToS/DSCP or IPv6 traffic class field \fItos\fR, which is
+specified as a decimal number between 0 and 255, inclusive. Note that
+the two lower reserved bits are ignored for matching purposes.
+.IP
+When \fBdl_type\fR is wildcarded or set to a value other than 0x0800 or
+0x86dd, the value of \fBnw_tos\fR is ignored (see \fBFlow Syntax\fR
+above).
+.
+.IP \fBnw_ecn=\fIecn\fR
+Matches \fIecn\fR bits in IP ToS or IPv6 traffic class fields, which is
+specified as a decimal number between 0 and 3, inclusive.
+.IP
+When \fBdl_type\fR is wildcarded or set to a value other than 0x0800 or
+0x86dd, the value of \fBnw_ecn\fR is ignored (see \fBFlow Syntax\fR
+above).
+.
+.IP \fBnw_ttl=\fIttl\fR
+Matches IP TTL or IPv6 hop limit value \fIttl\fR, which is
+specified as a decimal number between 0 and 255, inclusive.
+.IP
+When \fBdl_type\fR is wildcarded or set to a value other than 0x0800 or
+0x86dd, the value of \fBnw_ttl\fR is ignored (see \fBFlow Syntax\fR
+above).
.IP
-The value of \fBnw_proto\fR is silently ignored unless
-\fBdl_type=0x0800\fR, \fBip\fR, \fBicmp\fR, \fBtcp\fR, or \fBudp\fR is
-also specified.
.
.IP \fBtp_src=\fIport\fR
.IQ \fBtp_dst=\fIport\fR
When \fBdl_type\fR and \fBnw_proto\fR specify TCP or UDP, \fBtp_src\fR
and \fBtp_dst\fR match the UDP or TCP source or destination port
-\fIport\fR, respectively. which is specified as a decimal number
+\fIport\fR, respectively, which is specified as a decimal number
between 0 and 65535, inclusive (e.g. 80 to match packets originating
from a HTTP server).
.IP
When \fBdl_type\fR and \fBnw_proto\fR take other values, the values of
-these settings are silently ignored.
+these settings are ignored (see \fBFlow Syntax\fR above).
+.
+.IP \fBtp_src=\fIport\fB/\fImask\fR
+.IQ \fBtp_dst=\fIport\fB/\fImask\fR
+Bitwise match on TCP (or UDP) source or destination port,
+respectively. The \fIport\fR and \fImask\fR are 16-bit numbers
+written in decimal or in hexadecimal prefixed by \fB0x\fR. Each 1-bit
+in \fImask\fR requires that the corresponding bit in \fIport\fR must
+match. Each 0-bit in \fImask\fR causes the corresponding bit to be
+ignored.
+.IP
+Bitwise matches on transport ports are rarely useful in isolation, but
+a group of them can be used to reduce the number of flows required to
+match on a range of transport ports. For example, suppose that the
+goal is to match TCP source ports 1000 to 1999, inclusive. One way is
+to insert 1000 flows, each of which matches on a single source port.
+Another way is to look at the binary representations of 1000 and 1999,
+as follows:
+.br
+.B "01111101000"
+.br
+.B "11111001111"
+.br
+and then to transform those into a series of bitwise matches that
+accomplish the same results:
+.br
+.B "01111101xxx"
+.br
+.B "0111111xxxx"
+.br
+.B "10xxxxxxxxx"
+.br
+.B "110xxxxxxxx"
+.br
+.B "1110xxxxxxx"
+.br
+.B "11110xxxxxx"
+.br
+.B "1111100xxxx"
+.br
+which become the following when written in the syntax required by
+\fBovs\-ofctl\fR:
+.br
+.B "tcp,tp_src=0x03e8/0xfff8"
+.br
+.B "tcp,tp_src=0x03f0/0xfff0"
+.br
+.B "tcp,tp_src=0x0400/0xfe00"
+.br
+.B "tcp,tp_src=0x0600/0xff00"
+.br
+.B "tcp,tp_src=0x0700/0xff80"
+.br
+.B "tcp,tp_src=0x0780/0xffc0"
+.br
+.B "tcp,tp_src=0x07c0/0xfff0"
+.IP
+Only Open vSwitch 1.6 and later supports bitwise matching on transport
+ports.
+.IP
+Like the exact-match forms of \fBtp_src\fR and \fBtp_dst\fR described
+above, the bitwise match forms apply only when \fBdl_type\fR and
+\fBnw_proto\fR specify TCP or UDP.
.
.IP \fBicmp_type=\fItype\fR
.IQ \fBicmp_code=\fIcode\fR
-When \fBdl_type\fR and \fBnw_proto\fR specify ICMP, \fItype\fR matches
-the ICMP type and \fIcode\fR matches the ICMP code. Each is specified
-as a decimal number between 0 and 255, inclusive.
+When \fBdl_type\fR and \fBnw_proto\fR specify ICMP or ICMPv6, \fItype\fR
+matches the ICMP type and \fIcode\fR matches the ICMP code. Each is
+specified as a decimal number between 0 and 255, inclusive.
.IP
When \fBdl_type\fR and \fBnw_proto\fR take other values, the values of
-these settings are silently ignored.
+these settings are ignored (see \fBFlow Syntax\fR above).
+.
+.IP \fBtable=\fInumber\fR
+If specified, limits the flow manipulation and flow dump commands to
+only apply to the table with the given \fInumber\fR between 0 and 254.
+.
+Behavior varies if \fBtable\fR is not specified (equivalent to
+specifying 255 as \fInumber\fR). For flow table
+modification commands without \fB\-\-strict\fR, the switch will choose
+the table for these commands to operate on. For flow table
+modification commands with \fB\-\-strict\fR, the command will operate
+on any single matching flow in any table; it will do nothing if there
+are matches in more than one table. The \fBdump-flows\fR and
+\fBdump-aggregate\fR commands will gather statistics about flows from
+all tables.
+.IP
+When this field is specified in \fBadd-flow\fR, \fBadd-flows\fR,
+\fBmod-flows\fR and \fBdel-flows\fR commands, it activates a Nicira
+extension to OpenFlow, which as of this writing is only known to be
+implemented by Open vSwitch.
.
.PP
The following shorthand notations are also available:
Same as \fBdl_type=0x0806\fR.
.
.PP
-The \fBadd-flow\fR and \fBadd-flows\fR commands require an additional field:
+The following field assignments require support for the NXM (Nicira
+Extended Match) extension to OpenFlow. When one of these is specified,
+\fBovs\-ofctl\fR will automatically attempt to negotiate use of this
+extension. If the switch does not support NXM, then \fBovs\-ofctl\fR
+will report a fatal error.
+.
+.IP \fBvlan_tci=\fItci\fR[\fB/\fImask\fR]
+Matches modified VLAN TCI \fItci\fR. If \fImask\fR is omitted,
+\fItci\fR is the exact VLAN TCI to match; if \fImask\fR is specified,
+then a 1-bit in \fImask\fR indicates that the corresponding bit in
+\fItci\fR must match exactly, and a 0-bit wildcards that bit. Both
+\fItci\fR and \fImask\fR are 16-bit values that are decimal by
+default; use a \fB0x\fR prefix to specify them in hexadecimal.
+.
+.IP
+The value that \fBvlan_tci\fR matches against is 0 for a packet that
+has no 802.1Q header. Otherwise, it is the TCI value from the 802.1Q
+header with the CFI bit (with value \fB0x1000\fR) forced to 1.
+.IP
+Examples:
+.RS
+.IP \fBvlan_tci=0\fR
+Match only packets without an 802.1Q header.
+.IP \fBvlan_tci=0xf123\fR
+Match packets tagged with priority 7 in VLAN 0x123.
+.IP \fBvlan_tci=0x1123/0x1fff\fR
+Match packets tagged with VLAN 0x123 (and any priority).
+.IP \fBvlan_tci=0x5000/0xf000\fR
+Match packets tagged with priority 2 (in any VLAN).
+.IP \fBvlan_tci=0/0xfff\fR
+Match packets with no 802.1Q header or tagged with VLAN 0 (and any
+priority).
+.IP \fBvlan_tci=0x5000/0xe000\fR
+Match packets with no 802.1Q header or tagged with priority 2 (in any
+VLAN).
+.IP \fBvlan_tci=0/0xefff\fR
+Match packets with no 802.1Q header or tagged with VLAN 0 and priority
+0.
+.RE
+.IP
+Some of these matching possibilities can also be achieved with
+\fBdl_vlan\fR and \fBdl_vlan_pcp\fR.
+.
+.IP \fBip_frag=\fIfrag_type\fR
+When \fBdl_type\fR specifies IP or IPv6, \fIfrag_type\fR
+specifies what kind of IP fragments or non-fragments to match. The
+following values of \fIfrag_type\fR are supported:
+.RS
+.IP "\fBno\fR"
+Matches only non-fragmented packets.
+.IP "\fByes\fR"
+Matches all fragments.
+.IP "\fBfirst\fR"
+Matches only fragments with offset 0.
+.IP "\fBlater\fR"
+Matches only fragments with nonzero offset.
+.IP "\fBnot_later\fR"
+Matches non-fragmented packets and fragments with zero offset.
+.RE
+.IP
+The \fBip_frag\fR match type is likely to be most useful in
+\fBnx\-match\fR mode. See the description of the \fBset\-frags\fR
+command, above, for more details.
+.
+.IP \fBarp_sha=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+.IQ \fBarp_tha=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+When \fBdl_type\fR specifies ARP, \fBarp_sha\fR and \fBarp_tha\fR match
+the source and target hardware address, respectively. An address is
+specified as 6 pairs of hexadecimal digits delimited by colons.
+.
+.IP \fBipv6_src=\fIipv6\fR[\fB/\fInetmask\fR]
+.IQ \fBipv6_dst=\fIipv6\fR[\fB/\fInetmask\fR]
+When \fBdl_type\fR is 0x86dd (possibly via shorthand, e.g., \fBipv6\fR
+or \fBtcp6\fR), matches IPv6 source (or destination) address \fIipv6\fR,
+which may be specified as defined in RFC 2373. The preferred format is
+\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fB:\fIx\fR, where
+\fIx\fR are the hexadecimal values of the eight 16-bit pieces of the
+address. A single instance of \fB::\fR may be used to indicate multiple
+groups of 16-bits of zeros. The optional \fInetmask\fR allows
+restricting a match to an IPv6 address prefix. A netmask is specified
+as a CIDR block (e.g. \fB2001:db8:3c4d:1::/64\fR).
+.
+.IP \fBipv6_label=\fIlabel\fR
+When \fBdl_type\fR is 0x86dd (possibly via shorthand, e.g., \fBipv6\fR
+or \fBtcp6\fR), matches IPv6 flow label \fIlabel\fR.
+.
+.IP \fBnd_target=\fIipv6\fR[\fB/\fInetmask\fR]
+When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify
+IPv6 Neighbor Discovery (ICMPv6 type 135 or 136), matches the target address
+\fIipv6\fR. \fIipv6\fR is in the same format described earlier for the
+\fBipv6_src\fR and \fBipv6_dst\fR fields.
+.
+.IP \fBnd_sll=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify IPv6
+Neighbor Solicitation (ICMPv6 type 135), matches the source link\-layer
+address option. An address is specified as 6 pairs of hexadecimal
+digits delimited by colons.
+.
+.IP \fBnd_tll=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+When \fBdl_type\fR, \fBnw_proto\fR, and \fBicmp_type\fR specify IPv6
+Neighbor Advertisement (ICMPv6 type 136), matches the target link\-layer
+address option. An address is specified as 6 pairs of hexadecimal
+digits delimited by colons.
+.
+.IP \fBtun_id=\fItunnel-id\fR[\fB/\fImask\fR]
+Matches tunnel identifier \fItunnel-id\fR. Only packets that arrive
+over a tunnel that carries a key (e.g. GRE with the RFC 2890 key
+extension and a nonzero key value) will have a nonzero tunnel ID.
+If \fImask\fR is omitted, \fItunnel-id\fR is the exact tunnel ID to match;
+if \fImask\fR is specified, then a 1-bit in \fImask\fR indicates that the
+corresponding bit in \fItunnel-id\fR must match exactly, and a 0-bit
+wildcards that bit.
+.
+.IP "\fBreg\fIidx\fB=\fIvalue\fR[\fB/\fImask\fR]"
+Matches \fIvalue\fR either exactly or with optional \fImask\fR in
+register number \fIidx\fR. The valid range of \fIidx\fR depends on
+the switch. \fIvalue\fR and \fImask\fR are 32-bit integers, by
+default in decimal (use a \fB0x\fR prefix to specify hexadecimal).
+Arbitrary \fImask\fR values are allowed: a 1-bit in \fImask\fR
+indicates that the corresponding bit in \fIvalue\fR must match
+exactly, and a 0-bit wildcards that bit.
+.IP
+When a packet enters an OpenFlow switch, all of the registers are set
+to 0. Only explicit Nicira extension actions change register values.
+.
+.PP
+Defining IPv6 flows (those with \fBdl_type\fR equal to 0x86dd) requires
+support for NXM. The following shorthand notations are available for
+IPv6-related flows:
+.
+.IP \fBipv6\fR
+Same as \fBdl_type=0x86dd\fR.
+.
+.IP \fBtcp6\fR
+Same as \fBdl_type=0x86dd,nw_proto=6\fR.
+.
+.IP \fBudp6\fR
+Same as \fBdl_type=0x86dd,nw_proto=17\fR.
+.
+.IP \fBicmp6\fR
+Same as \fBdl_type=0x86dd,nw_proto=58\fR.
+.
+.PP
+Finally, field assignments to \fBduration\fR, \fBn_packets\fR, or
+\fBn_bytes\fR are ignored to allow output from the \fBdump\-flows\fR
+command to be used as input for other commands that parse flows.
+.
+.PP
+The \fBadd\-flow\fR, \fBadd\-flows\fR, and \fBmod\-flows\fR commands
+require an additional field, which must be the final field specified:
.
.IP \fBactions=\fR[\fItarget\fR][\fB,\fItarget\fR...]\fR
Specifies a comma-separated list of actions to take on a packet when the
.
.RS
.IP \fBoutput\fR:\fIport\fR
-Outputs the packet on the port specified by \fIport\fR.
+.IQ \fBoutput\fR:\fIsrc\fB[\fIstart\fB..\fIend\fB]
+Outputs the packet. If \fIport\fR is an OpenFlow port number, outputs directly
+to it. Otherwise, outputs to the OpenFlow port number read from \fIsrc\fR
+which must be an NXM field as described above. Outputting to an NXM field is
+an OpenFlow extension which is not supported by standard OpenFlow switches.
+.IP
+Example: \fBoutput:NXM_NX_REG0[16..31]\fR outputs to the OpenFlow port number
+written in the upper half of register 0.
+.
+.IP \fBenqueue\fR:\fIport\fB:\fIqueue\fR
+Enqueues the packet on the specified \fIqueue\fR within port
+\fIport\fR. The number of supported queues depends on the switch;
+some OpenFlow implementations do not support queuing at all.
.
.IP \fBnormal\fR
Subjects the packet to the device's normal L2/L3 processing. (This
Outputs the packet on all switch physical ports other than the port on
which it was received.
.
-.IP \fBcontroller\fR:\fImax_len\fR
+.IP \fBcontroller(\fIkey\fB=\fIvalue\fR...\fB)
Sends the packet to the OpenFlow controller as a ``packet in''
-message. If \fImax_len\fR is a number, then it specifies the maximum
-number of bytes that should be sent. If \fImax_len\fR is \fBALL\fR or
-omitted, then the entire packet is sent.
+message. The supported key-value pairs are:
+.RS
+.IP "\fBmax_len=\fInbytes\fR"
+Limit to \fInbytes\fR the number of bytes of the packet to send to
+the controller. By default the entire packet is sent.
+.IP "\fBreason=\fIreason\fR"
+Specify \fIreason\fR as the reason for sending the message in the
+``packet in'' message. The supported reasons are \fBaction\fR (the
+default), \fBno_match\fR, and \fBinvalid_ttl\fR.
+.IP "\fBid=\fIcontroller-id\fR"
+Specify \fIcontroller-id\fR, a 16-bit integer, as the connection ID of
+the OpenFlow controller or controllers to which the ``packet in''
+message should be sent. The default is zero. Zero is also the
+default connection ID for each controller connection, and a given
+controller connection will only have a nonzero connection ID if its
+controller uses the \fBNXT_SET_CONTROLLER_ID\fR Nicira extension to
+OpenFlow.
+.RE
+Any \fIreason\fR other than \fBaction\fR and any nonzero
+\fIcontroller-id\fR uses a Nicira vendor extension that, as of this
+writing, is only known to be implemented by Open vSwitch (version 1.6
+or later).
+.
+.IP \fBcontroller\fR
+.IQ \fBcontroller\fR[\fB:\fInbytes\fR]
+Shorthand for \fBcontroller()\fR or
+\fBcontroller(max_len=\fInbytes\fB)\fR, respectively.
.
.IP \fBlocal\fR
Outputs the packet on the ``local port,'' which corresponds to the
-\fBof\fIn\fR network device (see \fBCONTACTING THE CONTROLLER\fR in
-\fBovs\-openflowd\fR(8) for information on the \fBof\fIn\fR network device).
+network device that has the same name as the bridge.
+.
+.IP \fBin_port\fR
+Outputs the packet on the port from which it was received.
.
.IP \fBdrop\fR
Discards the packet, so no further processing or forwarding takes place.
Sets the TCP or UDP destination port to \fIport\fR.
.
.IP \fBmod_nw_tos\fB:\fItos\fR
-Sets the IP ToS/DSCP field to \fItos\fR. Valid values are between 0 and
+Sets the IPv4 ToS/DSCP field to \fItos\fR. Valid values are between 0 and
255, inclusive. Note that the two lower reserved bits are never
modified.
.
.RS
.
.IP \fBresubmit\fB:\fIport\fR
-Re-searches the OpenFlow flow table with the \fBin_port\fR field
-replaced by \fIport\fR and executes the actions found, if any, in
-addition to any other actions in this flow entry. Recursive
-\fBresubmit\fR actions are ignored.
+.IQ \fBresubmit\fB(\fR[\fIport\fR]\fB,\fR[\fItable\fR]\fB)
+Re-searches this OpenFlow flow table (or the table whose number is
+specified by \fItable\fR) with the \fBin_port\fR field replaced by
+\fIport\fR (if \fIport\fR is specified) and executes the actions
+found, if any, in addition to any other actions in this flow entry.
+.IP
+Recursive \fBresubmit\fR actions are obeyed up to an
+implementation-defined maximum depth. Open vSwitch 1.0.1 and earlier
+did not support recursion; Open vSwitch before 1.2.90 did not support
+\fItable\fR.
.
.IP \fBset_tunnel\fB:\fIid\fR
-If outputting to a port that encapsulates the packet in a tunnel and supports
-an identifier (such as GRE), sets the identifier to \fBid\fR.
+.IQ \fBset_tunnel64\fB:\fIid\fR
+If outputting to a port that encapsulates the packet in a tunnel and
+supports an identifier (such as GRE), sets the identifier to \fIid\fR.
+If the \fBset_tunnel\fR form is used and \fIid\fR fits in 32 bits,
+then this uses an action extension that is supported by Open vSwitch
+1.0 and later. Otherwise, if \fIid\fR is a 64-bit value, it requires
+Open vSwitch 1.1 or later.
+.
+.IP \fBset_queue\fB:\fIqueue\fR
+Sets the queue that should be used to \fIqueue\fR when packets are
+output. The number of supported queues depends on the switch; some
+OpenFlow implementations do not support queuing at all.
+.
+.IP \fBpop_queue\fR
+Restores the queue to the value it was before any \fBset_queue\fR
+actions were applied.
+.
+.IP \fBdec_ttl\fR
+Decrement TTL of IPv4 packet or hop limit of IPv6 packet. If the
+TTL or hop limit is initially zero, no decrement occurs. Instead,
+a ``packet-in'' message with reason code \fBOFPR_INVALID_TTL\fR is
+sent to each connected controller that has enabled receiving them,
+if any. Processing the current set of actions then stops.
+However, if the current set of actions was reached through
+``resubmit'' then remaining actions in outer levels resume
+processing.
+.
+.IP \fBnote:\fR[\fIhh\fR]...
+Does nothing at all. Any number of bytes represented as hex digits
+\fIhh\fR may be included. Pairs of hex digits may be separated by
+periods for readability.
+The \fBnote\fR action's format doesn't include an exact length for its
+payload, so the provided bytes will be padded on the right by enough
+bytes with value 0 to make the total number 6 more than a multiple of
+8.
+.
+.IP "\fBmove:\fIsrc\fB[\fIstart\fB..\fIend\fB]\->\fIdst\fB[\fIstart\fB..\fIend\fB]\fR"
+Copies the named bits from field \fIsrc\fR to field \fIdst\fR.
+\fIsrc\fR and \fIdst\fR must be NXM field names as defined in
+\fBnicira\-ext.h\fR, e.g. \fBNXM_OF_UDP_SRC\fR or \fBNXM_NX_REG0\fR.
+Each \fIstart\fR and \fIend\fR pair, which are inclusive, must specify
+the same number of bits and must fit within its respective field.
+Shorthands for \fB[\fIstart\fB..\fIend\fB]\fR exist: use
+\fB[\fIbit\fB]\fR to specify a single bit or \fB[]\fR to specify an
+entire field.
+.IP
+Examples: \fBmove:NXM_NX_REG0[0..5]\->NXM_NX_REG1[26..31]\fR copies the
+six bits numbered 0 through 5, inclusive, in register 0 into bits 26
+through 31, inclusive;
+\fBmove:NXM_NX_REG0[0..15]\->NXM_OF_VLAN_TCI[]\fR copies the least
+significant 16 bits of register 0 into the VLAN TCI field.
+.
+.IP "\fBload:\fIvalue\fB\->\fIdst\fB[\fIstart\fB..\fIend\fB]"
+Writes \fIvalue\fR to bits \fIstart\fR through \fIend\fR, inclusive,
+in field \fIdst\fR.
+.IP
+Example: \fBload:55\->NXM_NX_REG2[0..5]\fR loads value 55 (bit pattern
+\fB110111\fR) into bits 0 through 5, inclusive, in register 2.
+.
+.IP "\fBmultipath(\fIfields\fB, \fIbasis\fB, \fIalgorithm\fB, \fIn_links\fB, \fIarg\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR"
+Hashes \fIfields\fR using \fIbasis\fR as a universal hash parameter,
+then the applies multipath link selection \fIalgorithm\fR (with
+parameter \fIarg\fR) to choose one of \fIn_links\fR output links
+numbered 0 through \fIn_links\fR minus 1, and stores the link into
+\fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM field as
+described above.
+.IP
+Currently, \fIfields\fR must be either \fBeth_src\fR or
+\fBsymmetric_l4\fR and \fIalgorithm\fR must be one of \fBmodulo_n\fR,
+\fBhash_threshold\fR, \fBhrw\fR, and \fBiter_hash\fR. Only
+the \fBiter_hash\fR algorithm uses \fIarg\fR.
+.IP
+Refer to \fBnicira\-ext.h\fR for more details.
.
+.IP "\fBautopath(\fIid\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR"
+Given \fIid\fR, chooses an OpenFlow port and populates it in
+\fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM field as
+described above.
+.IP
+Currently, \fIid\fR should be the OpenFlow port number of an interface on the
+bridge. If it isn't then \fIdst\fB[\fIstart\fB..\fIend\fB]\fR will be
+populated with the OpenFlow port "none". If \fIid\fR is a member of a bond,
+the normal bond selection logic will be used to choose the destination port.
+Otherwise, the register will be populated with \fIid\fR itself.
+.IP
+Refer to \fBnicira\-ext.h\fR for more details.
+.
+.IP "\fBbundle(\fIfields\fB, \fIbasis\fB, \fIalgorithm\fB, \fIslave_type\fB, slaves:[\fIs1\fB, \fIs2\fB, ...])\fR"
+Hashes \fIfields\fR using \fIbasis\fR as a universal hash parameter, then
+applies the bundle link selection \fIalgorithm\fR to choose one of the listed
+slaves represented as \fIslave_type\fR. Currently the only supported
+\fIslave_type\fR is \fBofport\fR. Thus, each \fIs1\fR through \fIsN\fR should
+be an OpenFlow port number. Outputs to the selected slave.
+.IP
+Currently, \fIfields\fR must be either \fBeth_src\fR or \fBsymmetric_l4\fR and
+\fIalgorithm\fR must be one of \fBhrw\fR and \fBactive_backup\fR.
+.IP
+Example: \fBbundle(eth_src,0,hrw,ofport,slaves:4,8)\fR uses an Ethernet source
+hash with basis 0, to select between OpenFlow ports 4 and 8 using the Highest
+Random Weight algorithm.
+.IP
+Refer to \fBnicira\-ext.h\fR for more details.
+.
+.IP "\fBbundle_load(\fIfields\fB, \fIbasis\fB, \fIalgorithm\fB, \fIslave_type\fB, \fIdst\fB[\fIstart\fB..\fIend\fB], slaves:[\fIs1\fB, \fIs2\fB, ...])\fR"
+Has the same behavior as the \fBbundle\fR action, with one exception. Instead
+of outputting to the selected slave, it writes its selection to
+\fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM field as described
+above.
+.IP
+Example: \fBbundle_load(eth_src, 0, hrw, ofport, NXM_NX_REG0[],
+slaves:4, 8)\fR uses an Ethernet source hash with basis 0, to select
+between OpenFlow ports 4 and 8 using the Highest Random Weight
+algorithm, and writes the selection to \fBNXM_NX_REG0[]\fR.
+.IP
+Refer to \fBnicira\-ext.h\fR for more details.
+.
+.IP "\fBlearn(\fIargument\fR[\fB,\fIargument\fR]...\fB)\fR"
+This action adds or modifies a flow in an OpenFlow table, similar to
+\fBovs\-ofctl \-\-strict mod\-flows\fR. The arguments specify the
+flow's match fields, actions, and other properties, as follows. At
+least one match criterion and one action argument should ordinarily be
+specified.
+.RS
+.IP \fBidle_timeout=\fIseconds\fR
+.IQ \fBhard_timeout=\fIseconds\fR
+.IQ \fBpriority=\fIvalue\fR
+These key-value pairs have the same meaning as in the usual
+\fBovs\-ofctl\fR flow syntax.
+.
+.IP \fBfin_idle_timeout=\fIseconds\fR
+.IQ \fBfin_hard_timeout=\fIseconds\fR
+Adds a \fBfin_timeout\fR action with the specified arguments to the
+new flow. This feature was added in Open vSwitch 1.5.90.
+.
+.IP \fBtable=\fInumber\fR
+The table in which the new flow should be inserted. Specify a decimal
+number between 0 and 254. The default, if \fBtable\fR is unspecified,
+is table 1.
+.
+.IP \fIfield\fB=\fIvalue\fR
+.IQ \fIfield\fB[\fIstart\fB..\fIend\fB]=\fIsrc\fB[\fIstart\fB..\fIend\fB]\fR
+.IQ \fIfield\fB[\fIstart\fB..\fIend\fB]\fR
+Adds a match criterion to the new flow.
+.IP
+The first form specifies that \fIfield\fR must match the literal
+\fIvalue\fR, e.g. \fBdl_type=0x0800\fR. All of the fields and values
+for \fBovs\-ofctl\fR flow syntax are available with their usual
+meanings.
+.IP
+The second form specifies that \fIfield\fB[\fIstart\fB..\fIend\fB]\fR
+in the new flow must match \fIsrc\fB[\fIstart\fB..\fIend\fB]\fR taken
+from the flow currently being processed.
+.IP
+The third form is a shorthand for the second form. It specifies that
+\fIfield\fB[\fIstart\fB..\fIend\fB]\fR in the new flow must match
+\fIfield\fB[\fIstart\fB..\fIend\fB]\fR taken from the flow currently
+being processed.
+.
+.IP \fBload:\fIvalue\fB\->\fIdst\fB[\fIstart\fB..\fIend\fB]
+.IQ \fBload:\fIsrc\fB[\fIstart\fB..\fIend\fB]\->\fIdst\fB[\fIstart\fB..\fIend\fB]
+.
+Adds a \fBload\fR action to the new flow.
+.IP
+The first form loads the literal \fIvalue\fR into bits \fIstart\fR
+through \fIend\fR, inclusive, in field \fIdst\fR. Its syntax is the
+same as the \fBload\fR action described earlier in this section.
+.IP
+The second form loads \fIsrc\fB[\fIstart\fB..\fIend\fB]\fR, a value
+from the flow currently being processed, into bits \fIstart\fR
+through \fIend\fR, inclusive, in field \fIdst\fR.
+.
+.IP \fBoutput:\fIfield\fB[\fIstart\fB..\fIend\fB]\fR
+Add an \fBoutput\fR action to the new flow's actions, that outputs to
+the OpenFlow port taken from \fIfield\fB[\fIstart\fB..\fIend\fB]\fR,
+which must be an NXM field as described above.
+.RE
+.IP
+For best performance, segregate learned flows into a table (using
+\fBtable=\fInumber\fR) that is not used for any other flows except
+possibly for a lowest-priority ``catch-all'' flow, that is, a flow
+with no match criteria. (This is why the default \fBtable\fR is 1, to
+keep the learned flows separate from the primary flow table 0.)
.RE
.
+.IP "\fBfin_timeout(\fIargument\fR[\fB,\fIargument\fR]\fB)"
+This action changes the idle timeout or hard timeout, or both, of this
+OpenFlow rule when the rule matches a TCP packet with the FIN or RST
+flag. When such a packet is observed, the action reduces the rule's
+timeouts to those specified on the action. If the rule's existing
+timeout is already shorter than the one that the action specifies,
+then that timeout is unaffected.
+.IP
+\fIargument\fR takes the following forms:
+.RS
+.IP "\fBidle_timeout=\fIseconds\fR"
+Causes the flow to expire after the given number of seconds of
+inactivity.
+.
+.IP "\fBhard_timeout=\fIseconds\fR"
+Causes the flow to expire after the given number of seconds,
+regardless of activity. (\fIseconds\fR specifies time since the
+flow's creation, not since the receipt of the FIN or RST.)
+.RE
.IP
-(The OpenFlow protocol supports other actions that \fBovs\-ofctl\fR does
-not yet expose to the user.)
+This action was added in Open vSwitch 1.5.90.
+.IP "\fBexit\fR"
+This action causes Open vSwitch to immediately halt execution of further
+actions. Those actions which have already been executed are unaffected. Any
+further actions, including those which may be in other tables, or different
+levels of the \fBresubmit\fR call stack, are ignored.
.
.PP
-The \fBadd\-flow\fR, \fBadd\-flows\fR, and \fBmod\-flows\fR commands
-support an additional optional field:
+An opaque identifier called a cookie can be used as a handle to identify
+a set of flows:
.
.IP \fBcookie=\fIvalue\fR
.
-A cookie is an opaque identifier that can be associated with the flow.
-\fIvalue\fR can be any 64-bit number and need not be unique among
-flows.
+A cookie can be associated with a flow using the \fBadd\-flow\fR,
+\fBadd\-flows\fR, and \fBmod\-flows\fR commands. \fIvalue\fR can be any
+64-bit number and need not be unique among flows. If this field is
+omitted, a default cookie value of 0 is used.
+.
+.IP \fBcookie=\fIvalue\fR\fB/\fImask\fR
+.
+When using NXM, the cookie can be used as a handle for querying,
+modifying, and deleting flows. \fIvalue\fR and \fImask\fR may be
+supplied for the \fBdel\-flows\fR, \fBmod\-flows\fR, \fBdump\-flows\fR, and
+\fBdump\-aggregate\fR commands to limit matching cookies. A 1-bit in
+\fImask\fR indicates that the corresponding bit in \fIcookie\fR must
+match exactly, and a 0-bit wildcards that bit. A mask of \-1 may be used
+to exactly match a cookie.
+.IP
+The \fBmod\-flows\fR command can update the cookies of flows that
+match a cookie by specifying the \fIcookie\fR field twice (once with a
+mask for matching and once without to indicate the new value):
+.RS
+.IP "\fBovs\-ofctl mod\-flows br0 cookie=1,actions=normal\fR"
+Change all flows' cookies to 1 and change their actions to \fBnormal\fR.
+.IP "\fBovs\-ofctl mod\-flows br0 cookie=1/\-1,cookie=2,actions=normal\fR"
+Update cookies with a value of 1 to 2 and change their actions to
+\fBnormal\fR.
+.RE
+.IP
+The ability to match on cookies was added in Open vSwitch 1.5.0.
.
.PP
-The \fBadd-flow\fR, \fBadd-flows\fR, and \fBdel-flows\fR commands
-support an additional optional field:
+The following additional field sets the priority for flows added by
+the \fBadd\-flow\fR and \fBadd\-flows\fR commands. For
+\fBmod\-flows\fR and \fBdel\-flows\fR when \fB\-\-strict\fR is
+specified, priority must match along with the rest of the flow
+specification. For \fBmod-flows\fR without \fB\-\-strict\fR,
+priority is only significant if the command creates a new flow, that
+is, non-strict \fBmod\-flows\fR does not match on priority and will
+not change the priority of existing flows. Other commands do not
+allow priority to be specified.
.
.IP \fBpriority=\fIvalue\fR
The priority at which a wildcarded entry will match in comparison to
have priority over an entry containing wildcards, so it has an implicit
priority value of 65535. When adding a flow, if the field is not specified,
the flow's priority will default to 32768.
+.IP
+OpenFlow leaves behavior undefined when two or more flows with the
+same priority can match a single packet. Some users expect
+``sensible'' behavior, such as more specific flows taking precedence
+over less specific flows, but OpenFlow does not specify this and Open
+vSwitch does not implement it. Users should therefore take care to
+use priorities to ensure the behavior that they expect.
.
.PP
-The \fBadd-flow\fR and \fBadd-flows\fR commands support additional
-optional fields:
+The \fBadd\-flow\fR, \fBadd\-flows\fR, and \fBmod\-flows\fR commands
+support the following additional options. These options affect only
+new flows. Thus, for \fBadd\-flow\fR and \fBadd\-flows\fR, these
+options are always significant, but for \fBmod\-flows\fR they are
+significant only if the command creates a new flow, that is, their
+values do not update or affect existing flows.
.
-.TP
-\fBidle_timeout=\fIseconds\fR
+.IP "\fBidle_timeout=\fIseconds\fR"
Causes the flow to expire after the given number of seconds of
-inactivity. A value of 0 prevents a flow from expiring due to
-inactivity. The default is 60 seconds.
+inactivity. A value of 0 (the default) prevents a flow from expiring
+due to inactivity.
.
.IP \fBhard_timeout=\fIseconds\fR
Causes the flow to expire after the given number of seconds,
regardless of activity. A value of 0 (the default) gives the flow no
hard expiration deadline.
.
+.IP "\fBsend_flow_rem\fR"
+Marks the flow with a flag that causes the switch to generate a ``flow
+removed'' message and send it to interested controllers when the flow
+later expires or is removed.
+.
+.IP "\fBcheck_overlap\fR"
+Forces the switch to check that the flow match does not overlap that
+of any different flow with the same priority in the same table. (This
+check is expensive so it is best to avoid it.)
+.
.PP
-The \fBdump-flows\fR, \fBdump-aggregate\fR, \fBdel-flow\fR
-and \fBdel-flows\fR commands support one additional optional field:
+The \fBdump\-flows\fR, \fBdump\-aggregate\fR, \fBdel\-flow\fR
+and \fBdel\-flows\fR commands support one additional optional field:
.
.TP
\fBout_port=\fIport\fR
If set, a matching flow must include an output action to \fIport\fR.
.
-.PP
-The \fBdump-flows\fR and \fBdump-aggregate\fR commands support an
-additional optional field:
-.
-.IP \fBtable=\fInumber\fR
-If specified, limits the flows about which statistics are gathered to
-those in the table with the given \fInumber\fR. Tables are numbered
-as shown by the \fBdump-tables\fR command.
-.
-If this field is not specified, or if \fInumber\fR is given as
-\fB255\fR, statistics are gathered about flows from all tables.
-.
.SS "Table Entry Output"
.
-The \fBdump-tables\fR and \fBdump-aggregate\fR commands print information
+The \fBdump\-tables\fR and \fBdump\-aggregate\fR commands print information
about the entries in a datapath's tables. Each line of output is a
-unique flow entry, which begins with some common information:
-.
-.IP \fBduration\fR
-The number of seconds the entry has been in the table.
+flow entry as described in \fBFlow Syntax\fR, above, plus some
+additional fields:
.
-.IP \fBtable_id\fR
-The table that contains the flow. When a packet arrives, the switch
-begins searching for an entry at the lowest numbered table. Tables are
-numbered as shown by the \fBdump-tables\fR command.
-.
-.IP \fBpriority\fR
-The priority of the entry in relation to other entries within the same
-table. A higher value will match before a lower one.
+.IP \fBduration=\fIsecs\fR
+The time, in seconds, that the entry has been in the table.
+\fIsecs\fR includes as much precision as the switch provides, possibly
+to nanosecond resolution.
.
.IP \fBn_packets\fR
The number of packets that have matched the entry.
The total number of bytes from packets that have matched the entry.
.
.PP
-The rest of the line consists of a description of the flow entry as
-described in \fBFlow Syntax\fR, above.
+The following additional fields are included only if the switch is
+Open vSwitch 1.6 or later and the NXM flow format is used to dump the
+flow (see the description of the \fB\-\-flow-format\fR option below).
+The values of these additional fields are approximations only and in
+particular \fBidle_age\fR will sometimes become nonzero even for busy
+flows.
.
+.IP \fBhard_age=\fIsecs\fR
+The integer number of seconds since the flow was added or modified.
+\fBhard_age\fR is displayed only if it differs from the integer part
+of \fBduration\fR. (This is separate from \fBduration\fR because
+\fBmod\-flows\fR restarts the \fBhard_timeout\fR timer without zeroing
+\fBduration\fR.)
+.
+.IP \fBidle_age=\fIsecs\fR
+The integer number of seconds that have passed without any packets
+passing through the flow.
.
.SH OPTIONS
.TP
-\fB--strict\fR
+\fB\-\-strict\fR
Uses strict matching when running flow modification commands.
.
+.IP "\fB\-F \fIformat\fR[\fB,\fIformat\fR...]"
+.IQ "\fB\-\-flow\-format=\fIformat\fR[\fB,\fIformat\fR...]"
+\fBovs\-ofctl\fR supports the following individual flow formats, any
+number of which may be listed as \fIformat\fR:
+.RS
+.IP "\fBOpenFlow10\-table_id\fR"
+This is the standard OpenFlow 1.0 flow format. All OpenFlow switches
+and all versions of Open vSwitch support this flow format.
+.
+.IP "\fBOpenFlow10+table_id\fR"
+This is the standard OpenFlow 1.0 flow format plus a Nicira extension
+that allows \fBovs\-ofctl\fR to specify the flow table in which a
+particular flow should be placed. Open vSwitch 1.2 and later supports
+this flow format.
+.
+.IP "\fBNXM\-table_id\fR (Nicira Extended Match)"
+This Nicira extension to OpenFlow is flexible and extensible. It
+supports all of the Nicira flow extensions, such as \fBtun_id\fR and
+registers. Open vSwitch 1.1 and later supports this flow format.
+.
+.IP "\fBNXM+table_id\fR (Nicira Extended Match)"
+This combines Nicira Extended match with the ability to place a flow
+in a specific table. Open vSwitch 1.2 and later supports this flow
+format.
+.RE
+.
+.IP
+\fBovs\-ofctl\fR also supports the following abbreviations for
+collections of flow formats:
+.RS
+.IP "\fBany\fR"
+Any supported flow format.
+.IP "\fBOpenFlow10\fR"
+\fBOpenFlow10\-table_id\fR or \fBOpenFlow10+table_id\fR.
+.IP "\fBNXM\fR"
+\fBNXM\-table_id\fR or \fBNXM+table_id\fR.
+.RE
+.
+.IP
+For commands that modify the flow table, \fBovs\-ofctl\fR by default
+negotiates the most widely supported flow format that supports the
+flows being added. For commands that query the flow table,
+\fBovs\-ofctl\fR by default uses the most advanced format supported by
+the switch.
+.IP
+This option, where \fIformat\fR is a comma-separated list of one or
+more of the formats listed above, limits \fBovs\-ofctl\fR's choice of
+flow format. If a command cannot work as requested using one of the
+specified flow formats, \fBovs\-ofctl\fR will report a fatal error.
+.
+.IP "\fB\-P \fIformat\fR"
+.IQ "\fB\-\-packet\-in\-format=\fIformat\fR"
+\fBovs\-ofctl\fR supports the following packet_in formats, in order of
+increasing capability:
+.RS
+.IP "\fBopenflow10\fR"
+This is the standard OpenFlow 1.0 packet in format. It should be supported by
+all OpenFlow switches.
+.
+.IP "\fBnxm\fR (Nicira Extended Match)"
+This packet_in format includes flow metadata encoded using the NXM format.
+.
+.RE
+.IP
+Usually, \fBovs\-ofctl\fR prefers the \fBnxm\fR packet_in format, but will
+allow the switch to choose its default if \fBnxm\fR is unsupported. When
+\fIformat\fR is one of the formats listed in the above table, \fBovs\-ofctl\fR
+will insist on the selected format. If the switch does not support the
+requested format, \fBovs\-ofctl\fR will report a fatal error. This option only
+affects the \fBmonitor\fR command.
+.
+.IP "\fB\-\-timestamp\fR"
+Print a timestamp before each received packet. This option only
+affects the \fBmonitor\fR and \fBsnoop\fR commands.
+.
+.IP "\fB\-m\fR"
+.IQ "\fB\-\-more\fR"
+Increases the verbosity of OpenFlow messages printed and logged by
+\fBovs\-ofctl\fR commands. Specify this option more than once to
+increase verbosity further.
+.
+.ds DD \
+\fBovs\-ofctl\fR detaches only when executing the \fBmonitor\fR or \
+\fBsnoop\fR commands.
+.so lib/daemon.man
.SS "Public Key Infrastructure Options"
.so lib/ssl.man
.so lib/vlog.man
.so lib/common.man
.
+.SH "RUNTIME MANAGEMENT COMMANDS"
+\fBovs\-appctl\fR(8) can send commands to a running \fBovs\-ofctl\fR
+process. The supported commands are listed below.
+.
+.IP "\fBexit\fR"
+Causes \fBovs\-ofctl\fR to gracefully terminate. This command applies
+only when executing the \fBmonitor\fR or \fBsnoop\fR commands.
+.
+.IP "\fBofctl/set\-output\-file \fIfile\fR"
+Causes all subsequent output to go to \fIfile\fR instead of stderr.
+This command applies only when executing the \fBmonitor\fR or
+\fBsnoop\fR commands.
+.
+.IP "\fBofctl/send \fIofmsg\fR..."
+Sends each \fIofmsg\fR, specified as a sequence of hex digits that
+express an OpenFlow message, on the OpenFlow connection. This command
+is useful only when executing the \fBmonitor\fR command.
+.
+.IP "\fBofctl/barrier\fR"
+Sends an OpenFlow barrier request on the OpenFlow connection and waits
+for a reply. This command is useful only for the \fBmonitor\fR
+command.
+.
.SH EXAMPLES
.
-The following examples assume that an OpenFlow switch on the local
-host has been configured to listen for management connections on a
-Unix domain socket named \fB@RUNDIR@/openflow.sock\fR, e.g. by
-specifying \fB--listen=punix:@RUNDIR@/openflow.sock\fR on the
-\fBovs\-openflowd\fR(8) command line.
+The following examples assume that \fBovs\-vswitchd\fR has a bridge
+named \fBbr0\fR configured.
.
.TP
-\fBovs\-ofctl dump-tables unix:@RUNDIR@/openflow.sock\fR
+\fBovs\-ofctl dump\-tables br0\fR
Prints out the switch's table stats. (This is more interesting after
some traffic has passed through.)
.
.TP
-\fBovs\-ofctl dump-flows unix:@RUNDIR@/openflow.sock\fR
+\fBovs\-ofctl dump\-flows br0\fR
Prints the flow entries in the switch.
.
.SH "SEE ALSO"
git://git.onelab.eu / sliver-openvswitch.git / blobdiff