.IP \fBstrip_vlan\fR
Strips the VLAN tag from a packet if it is present.
.
+.IP \fBpush_vlan\fR:\fIethertype\fR
+Push a new VLAN tag onto the packet. Ethertype is used as the the Ethertype
+for the tag. Only ethertype 0x8100 should be used. (0x88a8 which the spec
+allows isn't supported at the moment.)
+A priority of zero and the tag of zero are used for the new tag.
+.
.IP \fBmod_dl_src\fB:\fImac\fR
Sets the source Ethernet address to \fImac\fR.
.
Sets the IPv4 ToS/DSCP field to \fItos\fR. Valid values are between 0 and
255, inclusive. Note that the two lower reserved bits are never
modified.
-.
.RE
.IP
The following actions are Nicira vendor extensions that, as of this writing, are
Example: \fBload:55\->NXM_NX_REG2[0..5]\fR loads value 55 (bit pattern
\fB110111\fR) into bits 0 through 5, inclusive, in register 2.
.
+.IP "\fBset_field:\fIvalue\fB\->\fIdst"
+Writes the literal \fIvalue\fR into the field \fIdst\fR, which should
+be specified as a name used for matching. (This is similar to
+\fBload\fR but more closely matches the set-field action defined in
+Open Flow 1.2 and above.)
+.
+.IP
+Example: \fBset_field:fe80:0123:4567:890a:a6ba:dbff:fefe:59fa\->ipv6_src\fR
+.
.IP "\fBmultipath(\fIfields\fB, \fIbasis\fB, \fIalgorithm\fB, \fIn_links\fB, \fIarg\fB, \fIdst\fB[\fIstart\fB..\fIend\fB])\fR"
Hashes \fIfields\fR using \fIbasis\fR as a universal hash parameter,
then the applies multipath link selection \fIalgorithm\fR (with
with no match criteria. (This is why the default \fBtable\fR is 1, to
keep the learned flows separate from the primary flow table 0.)
.
+.RS
+.IP \fBapply_actions(\fR[\fIaction\fR][\fB,\fIaction\fR...]\fB)
+Applies the specific action(s) immediately. The syntax of actions are same
+to \fBactions=\fR field.
+.
+.IP \fBclear_actions\fR
+Clears all the actions in the action set immediately.
+.
+.IP \fBwrite_metadata\fB:\fIvalue\fR[/\fImask\fR]
+Updates the metadata field for the flow. If \fImask\fR is omitted, the
+metadata field is set exactly to \fIvalue\fR; if \fImask\fR is specified, then
+a 1-bit in \fImask\fR indicates that the corresponding bit in the metadata
+field will be replaced with the corresponding bit from \fIvalue\fR. Both
+\fIvalue\fR and \fImask\fR are 64-bit values that are decimal by default; use
+a \fB0x\fR prefix to specify them in hexadecimal.
+.
+.IP \fBgoto_table\fR:\fItable\fR
+Indicates the next table in the process pipeline.
+.RE
+.
.IP "\fBfin_timeout(\fIargument\fR[\fB,\fIargument\fR]\fB)"
This action changes the idle timeout or hard timeout, or both, of this
OpenFlow rule when the rule matches a TCP packet with the FIN or RST