\fIport\fR is omitted, then statistics are printed for \fIqueue\fR on
every port where it exists.
.
-.SS "OpenFlow 1.1+ Switch Management Commands"
+.SS "OpenFlow 1.1+ Group Table Commands"
.
The following commands work only with switches that support OpenFlow
1.1 or later. Because support for OpenFlow 1.1 and later is still
groups are printed. See \fBGroup Syntax\fR, below, for the syntax of
\fIgroups\fR.
.
+.IP "\fBmod\-table \fIswitch\fR \fItable_id\fR \fIflow_miss_handling\fR"
+An OpenFlow 1.0 switch looks up each packet that arrives at the switch
+in table 0, then in table 1 if there is no match in table 0, then in
+table 2, and so on until the packet finds a match in some table.
+Finally, if no match was found, the switch sends the packet to the
+controller
+.IP
+OpenFlow 1.1 and later offer more flexibility. This command
+configures the flow table miss handling configuration for table
+\fItable_id\fR in \fIswitch\fR. \fItable_id\fR may be an OpenFlow
+table number between 0 and 254, inclusive, or the keyword \fBALL\fR to
+modify all tables. \fIflow_miss_handling\fR may be any one of the
+following:
+.RS
+.IP \fBdrop\fR
+Drop the packet.
+.IP \fBcontinue\fR
+Continue to the next table in the pipeline. (This is how an OpenFlow
+1.0 switch always handles packets that do not match any flow, in
+tables other than the last one.)
+.IP \fBcontroller\fR
+Send to controller. (This is how an OpenFlow 1.0 switch always
+handles packets that do not match any flow in the last table.)
+.RE
+.
+.SS "OpenFlow 1.3+ Switch Meter Table Commands"
+.
+These commands manage the meter table in an OpenFlow switch. In each
+case, \fImeter\fR specifies a meter entry in the format described in
+\fBMeter Syntax\fR, below.
+.
+.PP
+OpenFlow 1.3 introduced support for meters, so these commands only
+work with switches that support OpenFlow 1.3 or later. The caveats
+described for groups in the previous section also apply to meters.
+.
+.IP "\fBadd\-meter \fIswitch meter\fR"
+Add a meter entry to \fIswitch\fR's tables. The \fImeter\fR syntax is
+described in section \fBMeter Syntax\fR, below.
+.
+.IP "\fBmod\-meter \fIswitch meter\fR"
+Modify an existing meter.
+.
+.IP "\fBdel\-meters \fIswitch\fR"
+.IQ "\fBdel\-meter \fIswitch\fR [\fImeter\fR]"
+Delete entries from \fIswitch\fR's meter table. \fImeter\fR can specify
+a single meter with syntax \fBmeter=\fIid\fR, or all meters with syntax
+\fBmeter=all\fR.
+.
+.IP "\fBdump\-meters \fIswitch\fR"
+.IQ "\fBdump\-meter \fIswitch\fR [\fImeter\fR]"
+Print meter configuration. \fImeter\fR can specify a single meter with
+syntax \fBmeter=\fIid\fR, or all meters with syntax \fBmeter=all\fR.
+.
+.IP "\fBmeter\-stats \fIswitch\fR [\fImeter\fR]"
+Print meter statistics. \fImeter\fR can specify a single meter with
+syntax \fBmeter=\fIid\fR, or all meters with syntax \fBmeter=all\fR.
+.
+.IP "\fBmeter\-features \fIswitch\fR"
+Print meter features.
+.
.SS "OpenFlow Switch Flow Table Commands"
.
These commands manage the flow table in an OpenFlow switch. In each
If the packet does already contain an MPLS label, pushes a new
outermost label as a copy of the existing outermost label.
.IP
-There are some limitations in the implementation. \fBpush_mpls\fR
-followed by another \fBpush_mpls\fR will result in the first
-\fBpush_mpls\fR being discarded.
+A limitation of the implementation is that processing of actions will stop
+if \fBpush_mpls\fR follows another \fBpush_mpls\fR unless there is a
+\fBpop_mpls\fR in between.
.
.IP \fBpop_mpls\fR:\fIethertype\fR
Strips the outermost MPLS label stack entry.
Currently the implementation restricts \fIethertype\fR to a non-MPLS Ethertype
and thus \fBpop_mpls\fR should only be applied to packets with
-an MPLS label stack depth of one.
-.
-.IP
-There are some limitations in the implementation. \fBpop_mpls\fR
-followed by another \fBpush_mpls\fR without an intermediate
-\fBpush_mpls\fR will result in the first \fBpush_mpls\fR being
-discarded.
+an MPLS label stack depth of one. A further limitation is that processing of
+actions will stop if \fBpop_mpls\fR follows another \fBpop_mpls\fR unless
+there is a \fBpush_mpls\fR in between.
.
.IP \fBmod_dl_src\fB:\fImac\fR
Sets the source Ethernet address to \fImac\fR.
possibly for a lowest-priority ``catch-all'' flow, that is, a flow
with no match criteria. (This is why the default \fBtable\fR is 1, to
keep the learned flows separate from the primary flow table 0.)
+.RE
.
.RS
.IP \fBapply_actions(\fR[\fIaction\fR][\fB,\fIaction\fR...]\fB)
\fIvalue\fR and \fImask\fR are 64-bit values that are decimal by default; use
a \fB0x\fR prefix to specify them in hexadecimal.
.
+.IP \fBmeter\fR:\fImeter_id\fR
+Apply the \fImeter_id\fR before any other actions. If a meter band rate is
+exceeded, the packet may be dropped, or modified, depending on the meter
+band type. See the description of the \fBMeter Table Commands\fR, above,
+for more details.
+.
.IP \fBgoto_table\fR:\fItable\fR
Indicates the next table in the process pipeline.
-.RE
.
.IP "\fBfin_timeout(\fIargument\fR[\fB,\fIargument\fR]\fB)"
This action changes the idle timeout or hard timeout, or both, of this
.TP
\fBout_port=\fIport\fR
If set, a matching flow must include an output action to \fIport\fR,
-which must an OpenFlow port number or name (e.g. \fBlocal\fR).
+which must be an OpenFlow port number or name (e.g. \fBlocal\fR).
.
.SS "Table Entry Output"
.
for groups whose \fBtype\fR is \fBff\fR or \fBfast_failover\fR.
.RE
.
+.SS "Meter Syntax"
+.PP
+The meter table commands accept an argument that describes a meter.
+Such meter descriptions comprise a series \fIfield\fB=\fIvalue\fR
+assignments, separated by commas or white space.
+(Embedding spaces into a group description normally requires
+quoting to prevent the shell from breaking the description into
+multiple arguments.). Unless noted otherwise only the last instance
+of each field is honoured.
+.PP
+.IP \fBmeter=\fIid\fR
+The integer meter id of the meter.
+When this field is specified in \fBdel-meter\fR, \fBdump-meter\fR, or
+\fBmeter-stats\fR, the keyword "all" may be used to designate all meters.
+.
+This field is required, exept for \fBmeter-stats\fR, which dumps all stats
+when this field is not specified.
+
+.IP \fBkbps\fR
+.IQ \fBpktps\fR
+The unit for the meter band rate parameters, either kilobits per second, or
+packets per second, respectively. One of these must be specified. The burst
+size unit corresponds to the rate unit by dropping the "per second", i.e.,
+burst is in units of kilobits or packets, respectively.
+
+.IP \fBburst\fR
+Specify burst size for all bands, or none of them, if this flag is not given.
+
+.IP \fBstats\fR
+Collect meter and band statistics.
+
+.IP \fBbands\fR=\fIband_parameters\fR
+The \fBadd-meter\fR and \fBmod-meter\fR commands require at least one
+band specification. Bands must appear after all other fields.
+.RS
+.IP \fBtype=\fItype\fR
+The type of the meter band. This keyword starts a new band specification.
+Each band specifies a rate above which the band is to take some action. The
+action depends on the band type. If multiple bands' rate is exceeded, then
+the band with the highest rate among the exceeded bands is selected.
+The following keywords designate the allowed
+meter band types:
+.RS
+.IP \fBdrop\fR
+Drop packets exceeding the band's rate limit.
+.RE
+.
+.IP "The other \fIband_parameters\fR are:"
+.IP \fBrate=\fIvalue\fR
+The relative rate limit for this band, in kilobits per second or packets per
+second, depending on the meter flags defined above.
+.IP \fBburst_size=\fIport\fR
+The maximum burst allowed for the band. If unspecified, the switch is free to
+select some reasonable value depending on it's configuration.
+.RE
+.
.SH OPTIONS
.TP
\fB\-\-strict\fR
git://git.onelab.eu / sliver-openvswitch.git / blobdiff