.
.IP "\fBmonitor \fIswitch\fR [\fImiss-len\fR]"
Connects to \fIswitch\fR and prints to the console all OpenFlow
-messages received. Usually, \fIswitch\fR should specify a connection
-named on \fBovs\-openflowd\fR(8)'s \fB\-l\fR or \fB\-\-listen\fR command line
-option.
+messages received. Usually, \fIswitch\fR should specify the name of a
+bridge in the \fBovs\-vswitchd\fR database.
.IP
If \fImiss-len\fR is provided, \fBovs\-ofctl\fR sends an OpenFlow ``set
configuration'' message at connection setup time that requests
pairs of hexadecimal digits delimited by colons
(e.g. \fB00:0A:E4:25:6B:B0\fR).
.
+.IP \fBdl_dst=\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB/\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fB:\fIxx\fR
+Matches an Ethernet destination address specified as 6 pairs of
+hexadecimal digits delimited by colons (e.g. \fB00:0A:E4:25:6B:B0\fR),
+with a wildcard mask following the slash. Only
+the following masks are allowed:
+.RS
+.IP \fB01:00:00:00:00:00\fR
+Match only the multicast bit. Thus,
+\fBdl_dst=01:00:00:00:00:00/01:00:00:00:00:00\fR matches all multicast
+(including broadcast) Ethernet packets, and
+\fBdl_dst=00:00:00:00:00:00/01:00:00:00:00:00\fR matches all unicast
+Ethernet packets.
+.IP \fBfe:ff:ff:ff:ff:ff\fR
+Match all bits except the multicast bit. This is probably not useful.
+.IP \fBff:ff:ff:ff:ff:ff\fR
+Exact match (equivalent to omitting the mask).
+.IP \fB00:00:00:00:00:00\fR
+Wildcard all bits (equivalent to \fBdl_dst=*\fR.)
+.RE
+.
.IP \fBdl_type=\fIethertype\fR
Matches Ethernet protocol type \fIethertype\fR, which is specified as an
integer between 0 and 65535, inclusive, either in decimal or as a
.
.IP \fBlocal\fR
Outputs the packet on the ``local port,'' which corresponds to the
-\fBof\fIn\fR network device (see \fBCONTACTING THE CONTROLLER\fR in
-\fBovs\-openflowd\fR(8) for information on the \fBof\fIn\fR network device).
+network device that has the same name as the bridge.
.
.IP \fBdrop\fR
Discards the packet, so no further processing or forwarding takes place.
1.0 and later. Otherwise, if \fIid\fR is a 64-bit value, it requires
Open vSwitch 1.1 or later.
.
-.IP \fBdrop_spoofed_arp\fR
-Stops processing further actions, if the packet being processed is an
-Ethernet+IPv4 ARP packet for which the source Ethernet address inside
-the ARP packet differs from the source Ethernet address in the
-Ethernet header.
-.IP
-This action is deprecated in favor of defining flows using the
-\fBarp_sha\fR match field described earlier and will likely be removed
-in a future version of Open vSwitch.
-.
.IP \fBset_queue\fB:\fIqueue\fR
Sets the queue that should be used to \fIqueue\fR when packets are
output. The number of supported queues depends on the switch; some
.
.SH EXAMPLES
.
-The following examples assume that an OpenFlow switch on the local
-host has been configured to listen for management connections on a
-Unix domain socket named \fB@RUNDIR@/openflow.sock\fR, e.g. by
-specifying \fB\-\-listen=punix:@RUNDIR@/openflow.sock\fR on the
-\fBovs\-openflowd\fR(8) command line.
+The following examples assume that \fBovs\-vswitchd\fR has a bridge
+named \fBbr0\fR configured.
.
.TP
-\fBovs\-ofctl dump\-tables unix:@RUNDIR@/openflow.sock\fR
+\fBovs\-ofctl dump\-tables br0\fR
Prints out the switch's table stats. (This is more interesting after
some traffic has passed through.)
.
.TP
-\fBovs\-ofctl dump\-flows unix:@RUNDIR@/openflow.sock\fR
+\fBovs\-ofctl dump\-flows br0\fR
Prints the flow entries in the switch.
.
.SH "SEE ALSO"