much like a bridge separate from its ``parent bridge,'' but the actual
implementation in Open vSwitch uses only a single bridge, with ports on
the fake bridge assigned the implicit VLAN of the fake bridge of which
-they are members.
+they are members. (A fake bridge for VLAN 0 receives packets that
+have no 802.1Q tag or a tag with VLAN 0.)
.
.SH OPTIONS
.
Creates a ``fake bridge'' named \fIbridge\fR within the existing Open
vSwitch bridge \fIparent\fR, which must already exist and must not
itself be a fake bridge. The new fake bridge will be on 802.1Q VLAN
-\fIvlan\fR, which must be an integer between 1 and 4095. Initially
+\fIvlan\fR, which must be an integer between 0 and 4095. Initially
\fIbridge\fR will have no ports (other than \fIbridge\fR itself).
.IP
Without \fB\-\-may\-exist\fR, attempting to create a bridge that
.SS "OpenFlow Controller Connectivity"
.
\fBovs\-vswitchd\fR can perform all configured bridging and switching
-locally, or it can be configured to connect a given bridge to one or
-more external OpenFlow controllers, such as NOX.
+locally, or it can be configured to communicate with one or more
+external OpenFlow controllers. The switch is typically configured to
+connect to a primary controller that takes charge of the bridge's flow
+table to implement a network policy. In addition, the switch can be
+configured to listen to connections from service controllers. Service
+controllers are typically used for occasional support and maintenance,
+e.g. with \fBovs\-ofctl\fR.
.
.IP "\fBget\-controller\fR \fIbridge\fR"
Prints the configured controller target.
.
.RS
.so lib/vconn-active.man
+.so lib/vconn-passive.man
.RE
.
.ST "Controller Failure Settings"
is set, \fBovs\-vswitchd\fR will take over
responsibility for setting up
flows when no message has been received from the controller for three
-times the inactivity probe interval (xxx needs to be exposed). In this mode,
+times the inactivity probe interval. In this mode,
\fBovs\-vswitchd\fR causes the datapath to act like an ordinary
MAC-learning switch. \fBovs\-vswitchd\fR will continue to retry connecting
to the controller in the background and, when the connection succeeds,
.IP "[\fB\-\-columns=\fIcolumn\fR[\fB,\fIcolumn\fR]...] \fBfind \fItable \fR[\fIcolumn\fR[\fB:\fIkey\fR]\fB=\fIvalue\fR]..."
Lists the data in each record in \fItable\fR whose \fIcolumn\fR equals
\fIvalue\fR or, if \fIkey\fR is specified, whose \fIcolumn\fR contains
-a \fIkey\fR with the specified \fIvalue\fR. Any of the operators
-\fB!=\fR, \fB<\fR, \fB>\fR, \fB<=\fR, or \fB>=\fR may be substituted
-for \fB=\fR to test for inequality, less than, greater than, less than
-or equal to, or greater than or equal to, respectively. (Don't forget
-to escape \fB<\fR or \fB>\fR from interpretation by the shell.)
+a \fIkey\fR with the specified \fIvalue\fR. The following operators
+may be used where \fB=\fR is written in the syntax summary:
+.RS
+.IP "\fB= != < > <= >=\fR"
+Selects records in which \fIcolumn\fR[\fB:\fIkey\fR] equals, does not
+equal, is less than, is greater than, is less than or equal to, or is
+greater than or equal to \fIvalue\fR, respectively.
+.IP
+Consider \fIcolumn\fR[\fB:\fIkey\fR] and \fIvalue\fR as sets of
+elements. Identical sets are considered equal. Otherwise, if the
+sets have different numbers of elements, then the set with more
+elements is considered to be larger. Otherwise, consider a element
+from each set pairwise, in increasing order within each set. The
+first pair that differs determines the result. (For a column that
+contains key-value pairs, first all the keys are compared, and values
+are considered only if the two sets contain identical keys.)
+.IP "\fB{=} {!=}\fR"
+Test for set equality or inequality, respectively.
+.IP "\fB{<=}\fR"
+Selects records in which \fIcolumn\fR[\fB:\fIkey\fR] is a subset of
+\fIvalue\fR. For example, \fBflood-vlans{<=}1,2\fR selects records in
+which the \fBflood-vlans\fR column is the empty set or contains 1 or 2
+or both.
+.IP "\fB{<}\fR"
+Selects records in which \fIcolumn\fR[\fB:\fIkey\fR] is a proper
+subset of \fIvalue\fR. For example, \fBflood-vlans{<}1,2\fR selects
+records in which the \fBflood-vlans\fR column is the empty set or
+contains 1 or 2 but not both.
+.IP "\fB{>=} {>}\fR"
+Same as \fB{<=}\fR and \fB{<}\fR, respectively, except that the
+relationship is reversed. For example, \fBflood-vlans{>=}1,2\fR
+selects records in which the \fBflood-vlans\fR column contains both 1
+and 2.
+.RE
+.IP
+For arithmetic operators (\fB= != < > <= >=\fR), when \fIkey\fR is
+specified but a particular record's \fIcolumn\fR does not contain
+\fIkey\fR, the record is always omitted from the results. Thus, the
+condition \fBother-config:mtu!=1500\fR matches records that have a
+\fBmtu\fR key whose value is not 1500, but not those that lack an
+\fBmtu\fR key.
+.IP
+For the set operators, when \fIkey\fR is specified but a particular
+record's \fIcolumn\fR does not contain \fIkey\fR, the comparison is
+done against an empty set. Thus, the condition
+\fBother-config:mtu{!=}1500\fR matches records that have a \fBmtu\fR
+key whose value is not 1500 and those that lack an \fBmtu\fR key.
+.IP
+Don't forget to escape \fB<\fR or \fB>\fR from interpretation by the
+shell.
.IP
If \fB\-\-columns\fR is specified, only the requested columns are
listed, in the specified order. Otherwise all columns are listed, in
Consider specifying \fB\-\-timeout=0\fR along with
\fB\-\-wait\-until\fR, to prevent \fBovs\-vsctl\fR from terminating
after waiting only at most 5 seconds.
+.IP "\fBcomment \fR[\fIarg\fR]..."
+This command has no effect on behavior, but any database log record
+created by the command will include the command and its arguments.
.SH "EXAMPLES"
Create a new bridge named br0 and add port eth0 to it:
.IP
.PP
Monitor connectivity to a remote maintenance point on eth0.
.IP
-.B "ovs\-vsctl set Interface eth0 cfm_mpid=1 cfm_remote_mpid=2"
+.B "ovs\-vsctl set Interface eth0 cfm_mpid=1"
.PP
Deconfigure connectivity monitoring from above:
.IP
-.B "ovs\-vsctl clear Interface eth0 cfm_mpid cfm_remote_mpid"
+.B "ovs\-vsctl clear Interface eth0 cfm_mpid"
.SS "NetFlow"
.PP
Configure bridge \fBbr0\fR to send NetFlow records to UDP port 5566 on
.IP
.B "\-\- set Bridge br0 sflow=@s"
.PP
-Deconfigure sFlow from br0, which also destroys the sFlow record
+Deconfigure sFlow from \fBbr0\fR, which also destroys the sFlow record
(since it is now unreferenced):
.IP
.B "ovs\-vsctl \-\- clear Bridge br0 sflow"
+.SS "802.1D Spanning Tree Protocol (STP)"
+.PP
+Configure bridge \fBbr0\fR to participate in an 802.1D spanning tree:
+.IP
+.B "ovs\-vsctl set Bridge br0 stp_enable=true"
+.PP
+Set the bridge priority of \fBbr0\fR to 0x7800:
+.IP
+.B "ovs\-vsctl set Bridge br0 other_config:stp-priority=0x7800"
+.PP
+Set the path cost of port \fBeth0\fR to 10:
+.IP
+.B "ovs\-vsctl set Port eth0 other_config:stp-path-cost=10"
+.PP
+Deconfigure STP from above:
+.IP
+.B "ovs\-vsctl clear Bridge br0 stp_enable"
+.PP
.SH "EXIT STATUS"
.IP "0"
Successful program execution.
git://git.onelab.eu / sliver-openvswitch.git / blobdiff