configuration changes.
</column>
- <column name="capabilities">
- Describes functionality supported by the hardware and software platform
- on which this Open vSwitch is based. Clients should not modify this
- column. See the <ref table="Capability"/> description for defined
- capability categories and the meaning of associated
- <ref table="Capability"/> records.
- </column>
-
<group title="Statistics">
<p>
The <code>statistics</code> column contains key-value pairs that
<column name="ovs_version">
The Open vSwitch version number, e.g. <code>1.1.0</code>.
- If Open vSwitch was configured with a build number, then it is
- also included, e.g. <code>1.1.0+build6579</code>.
</column>
<column name="db_version">
</p>
</column>
+ <column name="cfm_fault_status" key="recv">
+ Indicates a CFM fault was triggered due to a lack of CCMs received on
+ the <ref table="Interface"/>.
+ </column>
+
+ <column name="cfm_fault_status" key="rdi">
+ Indicates a CFM fault was triggered due to the reception of a CCM with
+ the RDI bit flagged. Endpoints set the RDI bit in their CCMs when they
+ are not receiving CCMs themselves. This typically indicates a
+ unidirectional connectivity failure.
+ </column>
+
+ <column name="cfm_fault_status" key="maid">
+ Indicates a CFM fault was triggered due to the reception of a CCM with
+ a MAID other than the one Open vSwitch uses. CFM broadcasts are tagged
+ with an identification number in addition to the MPID called the MAID.
+ Open vSwitch only supports receiving CCM broadcasts tagged with the
+ MAID it uses internally.
+ </column>
+
+ <column name="cfm_fault_status" key="loopback">
+ Indicates a CFM fault was triggered due to the reception of a CCM
+ advertising the same MPID configured in the <ref column="cfm_mpid"/>
+ column of this <ref table="Interface"/>. This may indicate a loop in
+ the network.
+ </column>
+
+ <column name="cfm_fault_status" key="overflow">
+ Indicates a CFM fault was triggered because the CFM module received
+ CCMs from more remote endpoints than it can keep track of.
+ </column>
+
+ <column name="cfm_fault_status" key="override">
+ Indicates a CFM fault was manually triggered by an administrator using
+ an <code>ovs-appctl</code> command.
+ </column>
+
+ <column name="cfm_health">
+ <p>
+ Indicates the health of the interface as a percentage of CCM frames
+ received over 21 <ref column="other_config" key="cfm_interval"/>s.
+ The health of an interface is undefined if it is communicating with
+ more than one <ref column="cfm_remote_mpids"/>. It reduces if
+ healthy heartbeats are not received at the expected rate, and
+ gradually improves as healthy heartbeats are received at the desired
+ rate. Every 21 <ref column="other_config" key="cfm_interval"/>s, the
+ health of the interface is refreshed.
+ </p>
+ <p>
+ As mentioned above, the faults can be triggered for several reasons.
+ The link health will deteriorate even if heartbeats are received but
+ they are reported to be unhealthy. An unhealthy heartbeat in this
+ context is a heartbeat for which either some fault is set or is out
+ of sequence. The interface health can be 100 only on receiving
+ healthy heartbeats at the desired rate.
+ </p>
+ </column>
+
<column name="cfm_remote_mpids">
When CFM is properly configured, Open vSwitch will occasionally
receive CCM broadcasts. These broadcasts contain the MPID of the
<column name="other_config" key="cfm_ccm_vlan"
type='{"type": "integer", "minInteger": 1, "maxInteger": 4095}'>
When set, the CFM module will apply a VLAN tag to all CCMs it generates
- with the given value.
+ with the given value. May be the string <code>random</code> in which
+ case each CCM will be tagged with a different randomly generated VLAN.
</column>
<column name="other_config" key="cfm_ccm_pcp"
The virtual network to which this interface is attached.
</column>
+ <column name="external_ids" key="vm-id">
+ The VM to which this interface belongs. On XenServer, this will be the
+ same as <ref column="external_ids" key="xs-vm-uuid"/>.
+ </column>
+
<column name="external_ids" key="xs-vm-uuid">
The VM to which this interface belongs.
</column>
VLAN splinters increase kernel and userspace memory overhead, so do
not use them unless they are needed.
</p>
+
+ <p>
+ VLAN splinters do not support 802.1p priority tags. Received
+ priorities will appear to be 0, regardless of their actual values,
+ and priorities on transmitted packets will also be cleared to 0.
+ </p>
</column>
</group>
references it.</p>
<column name="type">
- <p>The type of QoS to implement. The <ref table="Open_vSwitch"
- column="capabilities"/> column in the <ref table="Open_vSwitch"/> table
- identifies the types that a switch actually supports. The currently
- defined types are listed below:</p>
+ <p>The type of QoS to implement. The currently defined types are
+ listed below:</p>
<dl>
<dt><code>linux-htb</code></dt>
<dd>
supported range of queue numbers depend on <ref column="type"/>. The
queue numbers are the same as the <code>queue_id</code> used in
OpenFlow in <code>struct ofp_action_enqueue</code> and other
- structures. Queue 0 is used by OpenFlow output actions that do not
- specify a specific queue.</p>
+ structures.</p>
+
+ <p>
+ Queue 0 is the ``default queue.'' It is used by OpenFlow output
+ actions when no specific queue has been set. When no configuration for
+ queue 0 is present, it is automatically configured as if a <ref
+ table="Queue"/> record with empty <ref table="Queue" column="dscp"/>
+ and <ref table="Queue" column="other_config"/> columns had been
+ specified.
+ (Before version 1.6, Open vSwitch would leave queue 0 unconfigured in
+ this case. With some queuing disciplines, this dropped all packets
+ destined for the default queue.)
+ </p>
</column>
<group title="Configuration for linux-htb and linux-hfsc">
</column>
</group>
- <group title="OpenFlow Rate Limiting">
+ <group title="Asynchronous Message Configuration">
+ <p>
+ OpenFlow switches send certain messages to controllers spontanenously,
+ that is, not in response to any request from the controller. These
+ messages are called ``asynchronous messages.'' These columns allow
+ asynchronous messages to be limited or disabled to ensure the best use
+ of network resources.
+ </p>
+
+ <column name="enable_async_messages">
+ The OpenFlow protocol enables asynchronous messages at time of
+ connection establishment, which means that a controller can receive
+ asynchronous messages, potentially many of them, even if it turns them
+ off immediately after connecting. Set this column to
+ <code>false</code> to change Open vSwitch behavior to disable, by
+ default, all asynchronous messages. The controller can use the
+ <code>NXT_SET_ASYNC_CONFIG</code> Nicira extension to OpenFlow to turn
+ on any messages that it does want to receive, if any.
+ </column>
+
<column name="controller_rate_limit">
<p>
The maximum rate at which the switch will forward packets to the
</column>
</group>
+ <group title="Connection Parameters">
+ <p>
+ Additional configuration for a connection between the controller
+ and the Open vSwitch.
+ </p>
+
+ <column name="other_config" key="dscp"
+ type='{"type": "integer"}'>
+ The Differentiated Service Code Point (DSCP) is specified in the IP
+ header. They are specified using 6 bits in the Type of Service (TOS)
+ field in the IP header. DSCP provides a mechanism to classify the
+ network traffic and provide the Quality of Service (QoS) on IP
+ networks.
+ The DSCP value passed is used when establishing the connection between
+ the controller and the Open vSwitch. The connection must be reset
+ for the new DSCP values to take effect. If no value is
+ specified, a default value of 192 is chosen for connection
+ establishment. Valid DSCP values must have their lower 2 bits set to 0.
+ </column>
+ </group>
+
+
<group title="Common Columns">
The overall purpose of these columns is described under <code>Common
Columns</code> at the beginning of this document.
<column name="external_ids"/>
+ <column name="other_config"/>
</group>
</table>
</column>
</group>
+ <group title="Connection Parameters">
+ <p>
+ Additional configuration for a connection between the manager
+ and the Open vSwitch Database.
+ </p>
+
+ <column name="other_config" key="dscp"
+ type='{"type": "integer"}'>
+ The Differentiated Service Code Point (DSCP) is specified in the IP
+ header. They are specified using 6 bits in the Type of Service (TOS)
+ field in the IP header. DSCP provides a mechanism to classify the
+ network traffic and provide the Quality of Service (QoS) on IP
+ networks.
+ The DSCP value passed when establishing the connection between
+ the manager and the Open vSwitch Database. The connection must be
+ reset for the new DSCP values to take effect. If no value is
+ specified, a default value of 192 is chosen for connection
+ establishment. Valid DSCP values must have their lower 2 bits set to 0.
+ </column>
+ </group>
+
<group title="Common Columns">
The overall purpose of these columns is described under <code>Common
Columns</code> at the beginning of this document.
<column name="external_ids"/>
+ <column name="other_config"/>
</group>
</table>
</group>
</table>
- <table name="Capability">
- <p>Records in this table describe functionality supported by the hardware
- and software platform on which this Open vSwitch is based. Clients
- should not modify this table.</p>
-
- <p>A record in this table is meaningful only if it is referenced by the
- <ref table="Open_vSwitch" column="capabilities"/> column in the
- <ref table="Open_vSwitch"/> table. The key used to reference it, called
- the record's ``category,'' determines the meanings of the
- <ref column="details"/> column. The following general forms of
- categories are currently defined:</p>
-
- <dl>
- <dt><code>qos-<var>type</var></code></dt>
- <dd><var>type</var> is supported as the value for
- <ref column="type" table="QoS"/> in the <ref table="QoS"/> table.
- </dd>
- </dl>
-
- <column name="details">
- <p>Key-value pairs that describe capabilities. The meaning of the pairs
- depends on the category key that the <ref table="Open_vSwitch"
- column="capabilities"/> column in the <ref table="Open_vSwitch"/> table
- uses to reference this record, as described above.</p>
-
- <p>The presence of a record for category <code>qos-<var>type</var></code>
- indicates that the switch supports <var>type</var> as the value of
- the <ref table="QoS" column="type"/> column in the <ref table="QoS"/>
- table. The following key-value pairs are defined to further describe
- QoS capabilities:</p>
-
- <dl>
- <dt><code>n-queues</code></dt>
- <dd>Number of supported queues, as a positive integer. Keys in the
- <ref table="QoS" column="queues"/> column for <ref table="QoS"/>
- records whose <ref table="QoS" column="type"/> value
- equals <var>type</var> must range between 0 and this value minus one,
- inclusive.</dd>
- </dl>
- </column>
- </table>
-
</database>
git://git.onelab.eu / sliver-openvswitch.git / blobdiff