and if Open vSwitch node does not run STP, then this option
should be enabled. Default is disabled, set to
<code>true</code> to enable.
+
+ The following destination MAC addresss will not be forwarded when this
+ option is enabled.
+ <dl>
+ <dt><code>01:80:c2:00:00:00</code></dt>
+ <dd>IEEE 802.1D Spanning Tree Protocol (STP).</dd>
+
+ <dt><code>01:80:c2:00:00:01</code></dt>
+ <dd>IEEE Pause frame.</dd>
+
+ <dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
+ <dd>Other reserved protocols.</dd>
+
+ <dt><code>00:e0:2b:00:00:00</code></dt>
+ <dd>Extreme Discovery Protocol (EDP).</dd>
+
+ <dt>
+ <code>00:e0:2b:00:00:04</code> and <code>00:e0:2b:00:00:06</code>
+ </dt>
+ <dd>Ethernet Automatic Protection Switching (EAPS).</dd>
+
+ <dt><code>01:00:0c:cc:cc:cc</code></dt>
+ <dd>
+ Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP),
+ Dynamic Trunking Protocol (DTP), Port Aggregation Protocol (PAgP),
+ and others.
+ </dd>
+
+ <dt><code>01:00:0c:cc:cc:cd</code></dt>
+ <dd>Cisco Shared Spanning Tree Protocol PVSTP+.</dd>
+
+ <dt><code>01:00:0c:cd:cd:cd</code></dt>
+ <dd>Cisco STP Uplink Fast.</dd>
+
+ <dt><code>01:00:0c:00:00:00</code></dt>
+ <dd>Cisco Inter Switch Link.</dd>
+
+ <dt><code>01:00:0c:cc:cc:c<var>x</var></code></dt>
+ <dd>Cisco CFM.</dd>
+ </dl>
</column>
<column name="other_config" key="mac-aging-time"
<column name="options" key="tos">
Optional. The value of the ToS bits to be set on the encapsulating
- packet. It may also be the word <code>inherit</code>, in which case
+ packet. ToS is interpreted as DSCP and ECN bits, ECN part must be
+ zero. It may also be the word <code>inherit</code>, in which case
the ToS will be copied from the inner packet if it is IPv4 or IPv6
(otherwise it will be 0). The ECN fields are always inherited.
Default is 0.
frame having an invalid interval.
</column>
- <column name="cfm_fault_status" key="sequence">
- Indicates a CFM fault was triggered because the CFM module received
- a CCM frame with a sequence number that it was not expecting.
+ <column name="cfm_remote_opstate">
+ <p>When in extended mode, indicates the operational state of the
+ remote endpoint as either <code>up</code> or <code>down</code>. See
+ <ref column="other_config" key="cfm_opstate"/>.
+ </p>
</column>
<column name="cfm_health">
<p>
The eviction process only considers flows that have an idle timeout or
a hard timeout. That is, eviction never deletes permanent flows.
- (Permanent flows do count against <ref column="flow_limit"/>.
+ (Permanent flows do count against <ref column="flow_limit"/>.)
</p>
<p>
sent out an implicit VLAN port, the frame will not be tagged. This
type of mirroring is sometimes called RSPAN.</p>
<p>
- The following destination MAC addresses will not be mirrored to a
- VLAN to avoid confusing switches that interpret the protocols that
- they represent:
+ See the documentation for
+ <ref column="other_config" key="forward-bpdu"/> in the
+ <ref table="Interface"/> table for a list of destination MAC
+ addresses which will not be mirrored to a VLAN to avoid confusing
+ switches that interpret the protocols that they represent.
</p>
- <dl>
- <dt><code>01:80:c2:00:00:00</code></dt>
- <dd>IEEE 802.1D Spanning Tree Protocol (STP).</dd>
-
- <dt><code>01:80:c2:00:00:01</code></dt>
- <dd>IEEE Pause frame.</dd>
-
- <dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
- <dd>Other reserved protocols.</dd>
-
- <dt><code>01:00:0c:cc:cc:cc</code></dt>
- <dd>
- Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP),
- Dynamic Trunking Protocol (DTP), Port Aggregation Protocol (PAgP),
- and others.
- </dd>
-
- <dt><code>01:00:0c:cc:cc:cd</code></dt>
- <dd>Cisco Shared Spanning Tree Protocol PVSTP+.</dd>
-
- <dt><code>01:00:0c:cd:cd:cd</code></dt>
- <dd>Cisco STP Uplink Fast.</dd>
-
- <dt><code>01:00:0c:00:00:00</code></dt>
- <dd>Cisco Inter Switch Link.</dd>
- </dl>
<p><em>Please note:</em> Mirroring to a VLAN can disrupt a network that
contains unmanaged switches. Consider an unmanaged physical switch
with two ports: port 1, connected to an end host, and port 2,
Service (QoS) on IP networks.
The DSCP value specified here is used when establishing the connection
- between the controller and the Open vSwitch. The connection must be
- reset for the new DSCP values to take effect. If no value is
- specified, a default value of 48 is chosen. Valid DSCP values must be
- in the range 0 to 63.
+ between the controller and the Open vSwitch. If no value is specified,
+ a default value of 48 is chosen. Valid DSCP values must be in the
+ range 0 to 63.
</column>
</group>
Service (QoS) on IP networks.
The DSCP value specified here is used when establishing the connection
- between the manager and the Open vSwitch. The connection must be
- reset for the new DSCP values to take effect. If no value is
- specified, a default value of 48 is chosen. Valid DSCP values must be
- in the range 0 to 63.
+ between the manager and the Open vSwitch. If no value is specified, a
+ default value of 48 is chosen. Valid DSCP values must be in the range
+ 0 to 63.
</column>
</group>
git://git.onelab.eu / sliver-openvswitch.git / blobdiff