(otherwise it will be the system default, typically 64).
Default is the system default TTL.</dd>
</dl>
+ <dl>
+ <dt><code>in_key</code></dt>
+ <dd>Optional. The WSI key that received packets must contain.
+ It may either be a 64-bit number (no key and a key of 0 are
+ treated as equivalent) or the word <code>flow</code>. If
+ <code>flow</code> is specified then any key will be accepted
+ and the key will be placed in the <code>tun_id</code> field
+ for matching in the flow table. The ovs-ofctl manual page
+ contains additional information about matching fields in
+ OpenFlow flows. Default is no key.</dd>
+ </dl>
+ <dl>
+ <dt><code>out_key</code></dt>
+ <dd>Optional. The WSI key to be set on outgoing packets. It may
+ either be a 64-bit number or the word <code>flow</code>. If
+ <code>flow</code> is specified then the key may be set using
+ the <code>set_tunnel</code> Nicira OpenFlow vendor extension (0
+ is used in the absence of an action). The ovs-ofctl manual
+ page contains additional information about the Nicira OpenFlow
+ vendor extensions. Default is no key.</dd>
+ </dl>
+ <dl>
+ <dt><code>key</code></dt>
+ <dd>Optional. Shorthand to set <code>in_key</code> and
+ <code>out_key</code> at the same time.</dd>
+ </dl>
<dl>
<dt><code>df_inherit</code></dt>
<dd>Optional. If enabled, the Don't Fragment bit will be copied
configurable transmission interval.
</p>
+ <p>
+ According to the 802.1ag specification, each Maintenance Point should
+ be configured out-of-band with a list of Remote Maintenance Points it
+ should have connectivity to. Open vSwitch differs from the
+ specification in this area. It simply assumes the link is faulted if
+ no Remote Maintenance Points are reachable, and considers it not
+ faulted otherwise.
+ </p>
+
<column name="cfm_mpid">
A Maintenance Point ID (MPID) uniquely identifies each endpoint within
a Maintenance Association. The MPID is used to identify this endpoint
CFM on this <ref table="Interface"/>.
</column>
- <column name="cfm_remote_mpid">
- The MPID of the remote endpoint being monitored. If this
- <ref table="Interface"/> does not have connectivity to an endpoint
- advertising the configured MPID, a fault is signalled. Must be
- configured to enable CFM on this <ref table="Interface"/>
- </column>
-
<column name="cfm_fault">
- Indicates a connectivity fault triggered by an inability to receive
- heartbeats from the remote endpoint. When a fault is triggered on
- <ref table="Interface"/>s participating in bonds, they will be
- disabled.
+ <p>
+ Indicates a connectivity fault triggered by an inability to receive
+ heartbeats from any remote endpoint. When a fault is triggered on
+ <ref table="Interface"/>s participating in bonds, they will be
+ disabled.
+ </p>
+ <p>
+ Faults can be triggered for several reasons. Most importantly they
+ are triggered when no CCMs are received for a period of 3.5 times the
+ transmission interval. Faults are also triggered when any CCMs
+ indicate that a Remote Maintenance Point is not receiving CCMs but
+ able to send them. Finally, a fault is triggered if a CCM is
+ received which indicates unexpected configuration. Notably, this
+ case arises when a CCM is received which advertises the local MPID.
+ </p>
</column>
</group>
<dd> The transmission interval of CFM heartbeats in milliseconds.
Three missed heartbeat receptions indicate a connectivity fault.
Defaults to 1000ms. </dd>
+ <dt><code>cfm_extended</code></dt>
+ <dd> When true, the CFM module operates in extended mode. This causes
+ it to use a nonstandard destination address to avoid conflicting
+ with compliant implementations which may be running concurrently on
+ the network. Furthermore, extended mode increases the accuracy of
+ the <code>cfm_interval</code> configuration parameter by breaking
+ wire compatibility with 802.1ag compliant implementations.
+ Defaults to false.</dd>
<dt><code>bond-stable-id</code></dt>
<dd> A positive integer using in <code>stable</code> bond mode to
make slave selection decisions. Allocating
git://git.onelab.eu / sliver-openvswitch.git / blobdiff