<dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
<dd>Other reserved protocols.</dd>
- <dt><code>00:00:5e:00:01:<var>x</var><var>x</var></code></dt>
- <dd> VRRP IPv4 virtual router MAC address. </dd>
+ <dt><code>00:e0:2b:00:00:00</code></dt>
+ <dd>Extreme Discovery Protocol (EDP).</dd>
- <dt><code>00:00:5e:00:02:<var>x</var><var>x</var></code></dt>
- <dd> VRRP IPv6 virtual router MAC address. </dd>
-
- <dt><code>00:00:0c:07:ac:<var>x</var><var>x</var></code></dt>
- <dd> HSRP Version 1. </dd>
-
- <dt><code>00:00:0c:9f:f<var>x</var>:<var>x</var><var>x</var></code>
- </dt>
- <dd> HSRP Version 2. </dd>
-
- <dt><code>00:07:b4:<var>x</var><var>x</var>:<var>x</var><var>x</var>:<var>x</var><var>x</var></code></dt>
- <dd> GLBP. </dd>
+ <dt>
+ <code>00:e0:2b:00:00:04</code> and <code>00:e0:2b:00:00:06</code>
+ </dt>
+ <dd>Ethernet Automatic Protection Switching (EAPS).</dd>
<dt><code>01:00:0c:cc:cc:cc</code></dt>
<dd>
<dt><code>01:00:0c:00:00:00</code></dt>
<dd>Cisco Inter Switch Link.</dd>
+
+ <dt><code>01:00:0c:cc:cc:c<var>x</var></code></dt>
+ <dd>Cisco CFM.</dd>
</dl>
</column>
<group title="Bonding Configuration">
<p>A port that has more than one interface is a ``bonded port.'' Bonding
- allows for load balancing and fail-over. Some kinds of bonding will
- work with any kind of upstream switch:</p>
+ allows for load balancing and fail-over.</p>
+
+ <p>
+ The following types of bonding will work with any kind of upstream
+ switch. On the upstream switch, do not configure the interfaces as a
+ bond:
+ </p>
<dl>
<dt><code>balance-slb</code></dt>
<dt><code>active-backup</code></dt>
<dd>
Assigns all flows to one slave, failing over to a backup slave when
- the active slave is disabled.
+ the active slave is disabled. This is the only bonding mode in which
+ interfaces may be plugged into different upstream switches.
</dd>
</dl>
<dt><code>stable</code></dt>
<dd>
+ <p>Deprecated and slated for removal in February 2013.</p>
<p>Attempts to always assign a given flow to the same slave
consistently. In an effort to maintain stability, no load
balancing is done. Uses a similar hashing strategy to
<column name="bond_updelay">
<p>
- The number of milliseconds for which carrier must stay up on an
+ The number of milliseconds for which the link must stay up on an
interface before the interface is considered to be up. Specify
<code>0</code> to enable the interface immediately.
</p>
</column>
<column name="bond_downdelay">
- The number of milliseconds for which carrier must stay down on an
+ The number of milliseconds for which the link must stay down on an
interface before the interface is considered to be down. Specify
<code>0</code> to disable the interface immediately.
</column>
</column>
</group>
- <group title="SLB Configuration">
+ <group title="Rebalancing Configuration">
<p>
These settings control behavior when a bond is in
- <code>balance-slb</code> mode, regardless of whether the bond was
- intentionally configured in SLB mode or it fell back to SLB mode
- because LACP negotiation failed.
+ <code>balance-slb</code> or <code>balance-tcp</code> mode.
</p>
<column name="other_config" key="bond-rebalance-interval"
successive attempts to rebalance the bond, that is, to move flows
from one interface on the bond to another in an attempt to keep usage
of each interface roughly equal. If zero, load balancing is disabled
- on the bond (carrier status changes still cause flows to move). If
+ on the bond (link failure still cause flows to move). If
less than 1000ms, the rebalance interval will be 1000ms.
</column>
</group>
frame having an invalid interval.
</column>
- <column name="cfm_fault_status" key="sequence">
- Indicates a CFM fault was triggered because the CFM module received
- a CCM frame with a sequence number that it was not expecting.
+ <column name="cfm_remote_opstate">
+ <p>When in extended mode, indicates the operational state of the
+ remote endpoint as either <code>up</code> or <code>down</code>. See
+ <ref column="other_config" key="cfm_opstate"/>.
+ </p>
</column>
<column name="cfm_health">
<p>
The eviction process only considers flows that have an idle timeout or
a hard timeout. That is, eviction never deletes permanent flows.
- (Permanent flows do count against <ref column="flow_limit"/>.
+ (Permanent flows do count against <ref column="flow_limit"/>.)
</p>
<p>
Service (QoS) on IP networks.
The DSCP value specified here is used when establishing the connection
- between the controller and the Open vSwitch. The connection must be
- reset for the new DSCP values to take effect. If no value is
- specified, a default value of 48 is chosen. Valid DSCP values must be
- in the range 0 to 63.
+ between the controller and the Open vSwitch. If no value is specified,
+ a default value of 48 is chosen. Valid DSCP values must be in the
+ range 0 to 63.
</column>
</group>
Service (QoS) on IP networks.
The DSCP value specified here is used when establishing the connection
- between the manager and the Open vSwitch. The connection must be
- reset for the new DSCP values to take effect. If no value is
- specified, a default value of 48 is chosen. Valid DSCP values must be
- in the range 0 to 63.
+ between the manager and the Open vSwitch. If no value is specified, a
+ default value of 48 is chosen. Valid DSCP values must be in the range
+ 0 to 63.
</column>
</group>
git://git.onelab.eu / sliver-openvswitch.git / blobdiff