<column name="ovs_version">
The Open vSwitch version number, e.g. <code>1.1.0</code>.
- If Open vSwitch was configured with a build number, then it is
- also included, e.g. <code>1.1.0+build6579</code>.
</column>
<column name="db_version">
any defined controllers forever.</dd>
</dl>
</p>
- <p>If this value is unset, the default is implementation-specific.</p>
+ <p>
+ The default is <code>standalone</code> if the value is unset, but
+ future versions of Open vSwitch may change the default.
+ </p>
+ <p>
+ The <code>standalone</code> mode can create forwarding loops on a
+ bridge that has more than one uplink port unless STP is enabled. To
+ avoid loops on such a bridge, configure <code>secure</code> mode or
+ enable STP (see <ref column="stp_enable"/>).
+ </p>
<p>When more than one controller is configured,
<ref column="fail_mode"/> is considered only when none of the
configured controllers can be contacted.</p>
and if Open vSwitch node does not run STP, then this option
should be enabled. Default is disabled, set to
<code>true</code> to enable.
+
+ The following destination MAC addresss will not be forwarded when this
+ option is enabled.
+ <dl>
+ <dt><code>01:80:c2:00:00:00</code></dt>
+ <dd>IEEE 802.1D Spanning Tree Protocol (STP).</dd>
+
+ <dt><code>01:80:c2:00:00:01</code></dt>
+ <dd>IEEE Pause frame.</dd>
+
+ <dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
+ <dd>Other reserved protocols.</dd>
+
+ <dt><code>00:e0:2b:00:00:00</code></dt>
+ <dd>Extreme Discovery Protocol (EDP).</dd>
+
+ <dt>
+ <code>00:e0:2b:00:00:04</code> and <code>00:e0:2b:00:00:06</code>
+ </dt>
+ <dd>Ethernet Automatic Protection Switching (EAPS).</dd>
+
+ <dt><code>01:00:0c:cc:cc:cc</code></dt>
+ <dd>
+ Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP),
+ Dynamic Trunking Protocol (DTP), Port Aggregation Protocol (PAgP),
+ and others.
+ </dd>
+
+ <dt><code>01:00:0c:cc:cc:cd</code></dt>
+ <dd>Cisco Shared Spanning Tree Protocol PVSTP+.</dd>
+
+ <dt><code>01:00:0c:cd:cd:cd</code></dt>
+ <dd>Cisco STP Uplink Fast.</dd>
+
+ <dt><code>01:00:0c:00:00:00</code></dt>
+ <dd>Cisco Inter Switch Link.</dd>
+
+ <dt><code>01:00:0c:cc:cc:c<var>x</var></code></dt>
+ <dd>Cisco CFM.</dd>
+ </dl>
</column>
<column name="other_config" key="mac-aging-time"
<group title="Bonding Configuration">
<p>A port that has more than one interface is a ``bonded port.'' Bonding
- allows for load balancing and fail-over. Some kinds of bonding will
- work with any kind of upstream switch:</p>
+ allows for load balancing and fail-over.</p>
+
+ <p>
+ The following types of bonding will work with any kind of upstream
+ switch. On the upstream switch, do not configure the interfaces as a
+ bond:
+ </p>
<dl>
<dt><code>balance-slb</code></dt>
<dt><code>active-backup</code></dt>
<dd>
Assigns all flows to one slave, failing over to a backup slave when
- the active slave is disabled.
+ the active slave is disabled. This is the only bonding mode in which
+ interfaces may be plugged into different upstream switches.
</dd>
</dl>
<dt><code>stable</code></dt>
<dd>
+ <p>Deprecated and slated for removal in February 2013.</p>
<p>Attempts to always assign a given flow to the same slave
consistently. In an effort to maintain stability, no load
balancing is done. Uses a similar hashing strategy to
<column name="bond_updelay">
<p>
- The number of milliseconds for which carrier must stay up on an
+ The number of milliseconds for which the link must stay up on an
interface before the interface is considered to be up. Specify
<code>0</code> to enable the interface immediately.
</p>
</column>
<column name="bond_downdelay">
- The number of milliseconds for which carrier must stay down on an
+ The number of milliseconds for which the link must stay down on an
interface before the interface is considered to be down. Specify
<code>0</code> to disable the interface immediately.
</column>
numerically lower priority.
</column>
- <column name="other_config" key="lacp-time">
+ <column name="other_config" key="lacp-time"
+ type='{"type": "string", "enum": ["set", ["fast", "slow"]]}'>
<p>
The LACP timing which should be used on this <ref table="Port"/>.
- Possible values are <code>fast</code>, <code>slow</code> and a
- positive number of milliseconds. By default <code>slow</code> is
- used. When configured to be <code>fast</code> LACP heartbeats are
- requested at a rate of once per second causing connectivity
- problems to be detected more quickly. In <code>slow</code> mode,
- heartbeats are requested at a rate of once every 30 seconds.
- </p>
-
- <p>
- Users may manually set a heartbeat transmission rate to increase
- the fault detection speed further. When manually set, OVS expects
- the partner switch to be configured with the same transmission
- rate. Manually setting <code>lacp-time</code> to something other
- than <code>fast</code> or <code>slow</code> is not supported by the
- LACP specification.
+ By default <code>slow</code> is used. When configured to be
+ <code>fast</code> LACP heartbeats are requested at a rate of once
+ per second causing connectivity problems to be detected more
+ quickly. In <code>slow</code> mode, heartbeats are requested at a
+ rate of once every 30 seconds.
</p>
</column>
-
- <column name="other_config" key="lacp-heartbeat"
- type='{"type": "boolean"}'>
- Treat LACP like a simple heartbeat protocol for link state
- monitoring. Most features of the LACP protocol are disabled
- when this mode is in use. The default if not specified is
- <code>false</code>.
- </column>
</group>
- <group title="SLB Configuration">
+ <group title="Rebalancing Configuration">
<p>
These settings control behavior when a bond is in
- <code>balance-slb</code> mode, regardless of whether the bond was
- intentionally configured in SLB mode or it fell back to SLB mode
- because LACP negotiation failed.
+ <code>balance-slb</code> or <code>balance-tcp</code> mode.
</p>
<column name="other_config" key="bond-rebalance-interval"
successive attempts to rebalance the bond, that is, to move flows
from one interface on the bond to another in an attempt to keep usage
of each interface roughly equal. If zero, load balancing is disabled
- on the bond (carrier status changes still cause flows to move). If
+ on the bond (link failure still cause flows to move). If
less than 1000ms, the rebalance interval will be 1000ms.
</column>
</group>
<column name="options" key="tos">
Optional. The value of the ToS bits to be set on the encapsulating
- packet. It may also be the word <code>inherit</code>, in which case
+ packet. ToS is interpreted as DSCP and ECN bits, ECN part must be
+ zero. It may also be the word <code>inherit</code>, in which case
the ToS will be copied from the inner packet if it is IPv4 or IPv6
(otherwise it will be 0). The ECN fields are always inherited.
Default is 0.
an <code>ovs-appctl</code> command.
</column>
+ <column name="cfm_fault_status" key="interval">
+ Indicates a CFM fault was triggered due to the reception of a CCM
+ frame having an invalid interval.
+ </column>
+
+ <column name="cfm_remote_opstate">
+ <p>When in extended mode, indicates the operational state of the
+ remote endpoint as either <code>up</code> or <code>down</code>. See
+ <ref column="other_config" key="cfm_opstate"/>.
+ </p>
+ </column>
+
+ <column name="cfm_health">
+ <p>
+ Indicates the health of the interface as a percentage of CCM frames
+ received over 21 <ref column="other_config" key="cfm_interval"/>s.
+ The health of an interface is undefined if it is communicating with
+ more than one <ref column="cfm_remote_mpids"/>. It reduces if
+ healthy heartbeats are not received at the expected rate, and
+ gradually improves as healthy heartbeats are received at the desired
+ rate. Every 21 <ref column="other_config" key="cfm_interval"/>s, the
+ health of the interface is refreshed.
+ </p>
+ <p>
+ As mentioned above, the faults can be triggered for several reasons.
+ The link health will deteriorate even if heartbeats are received but
+ they are reported to be unhealthy. An unhealthy heartbeat in this
+ context is a heartbeat for which either some fault is set or is out
+ of sequence. The interface health can be 100 only on receiving
+ healthy heartbeats at the desired rate.
+ </p>
+ </column>
+
<column name="cfm_remote_mpids">
When CFM is properly configured, Open vSwitch will occasionally
receive CCM broadcasts. These broadcasts contain the MPID of the
<column name="other_config" key="cfm_interval"
type='{"type": "integer"}'>
- The interval, in milliseconds, between transmissions of CFM heartbeats.
- Three missed heartbeat receptions indicate a connectivity fault.
- Defaults to 1000.
+ <p>
+ The interval, in milliseconds, between transmissions of CFM
+ heartbeats. Three missed heartbeat receptions indicate a
+ connectivity fault.
+ </p>
+
+ <p>
+ In standard operation only intervals of 3, 10, 100, 1,000, 10,000,
+ 60,000, or 600,000 ms are supported. Other values will be rounded
+ down to the nearest value on the list. Extended mode (see <ref
+ column="other_config" key="cfm_extended"/>) supports any interval up
+ to 65,535 ms. In either mode, the default is 1000 ms.
+ </p>
+
+ <p>We do not recommend using intervals less than 100 ms.</p>
</column>
<column name="other_config" key="cfm_extended"
<column name="other_config" key="cfm_ccm_vlan"
type='{"type": "integer", "minInteger": 1, "maxInteger": 4095}'>
When set, the CFM module will apply a VLAN tag to all CCMs it generates
- with the given value.
+ with the given value. May be the string <code>random</code> in which
+ case each CCM will be tagged with a different randomly generated VLAN.
</column>
<column name="other_config" key="cfm_ccm_pcp"
commonly be the same as <ref column="external_ids" key="xs-vif-uuid"/>.
</column>
+ <column name="external_ids" key="iface-status"
+ type='{"type": "string",
+ "enum": ["set", ["active", "inactive"]]}'>
+ <p>
+ Hypervisors may sometimes have more than one interface associated
+ with a given <ref column="external_ids" key="iface-id"/>, only one of
+ which is actually in use at a given time. For example, in some
+ circumstances XenServer has both a ``tap'' and a ``vif'' interface
+ for a single <ref column="external_ids" key="iface-id"/>, but only
+ uses one of them at a time. A hypervisor that behaves this way must
+ mark the currently in use interface <code>active</code> and the
+ others <code>inactive</code>. A hypervisor that never has more than
+ one interface for a given <ref column="external_ids" key="iface-id"/>
+ may mark that interface <code>active</code> or omit <ref
+ column="external_ids" key="iface-status"/> entirely.
+ </p>
+
+ <p>
+ During VM migration, a given <ref column="external_ids"
+ key="iface-id"/> might transiently be marked <code>active</code> on
+ two different hypervisors. That is, <code>active</code> means that
+ this <ref column="external_ids" key="iface-id"/> is the active
+ instance within a single hypervisor, not in a broader scope.
+ </p>
+ </column>
+
<column name="external_ids" key="xs-vif-uuid">
The virtual interface associated with this interface.
</column>
<p>
The eviction process only considers flows that have an idle timeout or
a hard timeout. That is, eviction never deletes permanent flows.
- (Permanent flows do count against <ref column="flow_limit"/>.
+ (Permanent flows do count against <ref column="flow_limit"/>.)
</p>
<p>
sent out an implicit VLAN port, the frame will not be tagged. This
type of mirroring is sometimes called RSPAN.</p>
<p>
- The following destination MAC addresses will not be mirrored to a
- VLAN to avoid confusing switches that interpret the protocols that
- they represent:
+ See the documentation for
+ <ref column="other_config" key="forward-bpdu"/> in the
+ <ref table="Interface"/> table for a list of destination MAC
+ addresses which will not be mirrored to a VLAN to avoid confusing
+ switches that interpret the protocols that they represent.
</p>
- <dl>
- <dt><code>01:80:c2:00:00:00</code></dt>
- <dd>IEEE 802.1D Spanning Tree Protocol (STP).</dd>
-
- <dt><code>01:80:c2:00:00:01</code></dt>
- <dd>IEEE Pause frame.</dd>
-
- <dt><code>01:80:c2:00:00:0<var>x</var></code></dt>
- <dd>Other reserved protocols.</dd>
-
- <dt><code>01:00:0c:cc:cc:cc</code></dt>
- <dd>
- Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP),
- Dynamic Trunking Protocol (DTP), Port Aggregation Protocol (PAgP),
- and others.
- </dd>
-
- <dt><code>01:00:0c:cc:cc:cd</code></dt>
- <dd>Cisco Shared Spanning Tree Protocol PVSTP+.</dd>
-
- <dt><code>01:00:0c:cd:cd:cd</code></dt>
- <dd>Cisco STP Uplink Fast.</dd>
-
- <dt><code>01:00:0c:00:00:00</code></dt>
- <dd>Cisco Inter Switch Link.</dd>
- </dl>
<p><em>Please note:</em> Mirroring to a VLAN can disrupt a network that
contains unmanaged switches. Consider an unmanaged physical switch
with two ports: port 1, connected to an end host, and port 2,
</column>
</group>
+ <group title="Connection Parameters">
+ <p>
+ Additional configuration for a connection between the controller
+ and the Open vSwitch.
+ </p>
+
+ <column name="other_config" key="dscp"
+ type='{"type": "integer"}'>
+ The Differentiated Service Code Point (DSCP) is specified using 6 bits
+ in the Type of Service (TOS) field in the IP header. DSCP provides a
+ mechanism to classify the network traffic and provide Quality of
+ Service (QoS) on IP networks.
+
+ The DSCP value specified here is used when establishing the connection
+ between the controller and the Open vSwitch. If no value is specified,
+ a default value of 48 is chosen. Valid DSCP values must be in the
+ range 0 to 63.
+ </column>
+ </group>
+
+
<group title="Common Columns">
The overall purpose of these columns is described under <code>Common
Columns</code> at the beginning of this document.
<column name="external_ids"/>
+ <column name="other_config"/>
</group>
</table>
</column>
</group>
+ <group title="Connection Parameters">
+ <p>
+ Additional configuration for a connection between the manager
+ and the Open vSwitch Database.
+ </p>
+
+ <column name="other_config" key="dscp"
+ type='{"type": "integer"}'>
+ The Differentiated Service Code Point (DSCP) is specified using 6 bits
+ in the Type of Service (TOS) field in the IP header. DSCP provides a
+ mechanism to classify the network traffic and provide Quality of
+ Service (QoS) on IP networks.
+
+ The DSCP value specified here is used when establishing the connection
+ between the manager and the Open vSwitch. If no value is specified, a
+ default value of 48 is chosen. Valid DSCP values must be in the range
+ 0 to 63.
+ </column>
+ </group>
+
<group title="Common Columns">
The overall purpose of these columns is described under <code>Common
Columns</code> at the beginning of this document.
<column name="external_ids"/>
+ <column name="other_config"/>
</group>
</table>
git://git.onelab.eu / sliver-openvswitch.git / blobdiff