struct bus_type {
...
- int (*suspend)(struct device * dev, u32 state);
+ int (*suspend)(struct device * dev, pm_message_t state);
int (*resume)(struct device * dev);
};
# NOTIFICATION -- pretty much same as ON?
-FREEZE -- stop DMA and interrupts, and be prepared to reinit HW from
-scratch. That probably means stop accepting upstream requests, the
-actual policy of what to do with them beeing specific to a given
-driver. It's acceptable for a network driver to just drop packets
-while a block driver is expected to block the queue so no request is
-lost. (Use IDE as an example on how to do that). FREEZE requires no
-power state change, and it's expected for drivers to be able to
-quickly transition back to operating state.
-
-SUSPEND -- like FREEZE, but also put hardware into low-power state. If
-there's need to distinguish several levels of sleep, additional flag
-is probably best way to do that.
-
-Transitions are only from a resumed state to a suspended state, never
-between 2 suspended states. (ON -> FREEZE or ON -> SUSPEND can happen,
-FREEZE -> SUSPEND or SUSPEND -> FREEZE can not).
-
-All events are:
-
-[NOTE NOTE NOTE: If you are driver author, you should not care; you
-should only look at event, and ignore flags.]
-
-#Prepare for suspend -- userland is still running but we are going to
-#enter suspend state. This gives drivers chance to load firmware from
-#disk and store it in memory, or do other activities taht require
-#operating userland, ability to kmalloc GFP_KERNEL, etc... All of these
-#are forbiden once the suspend dance is started.. event = ON, flags =
-#PREPARE_TO_SUSPEND
-
-Apm standby -- prepare for APM event. Quiesce devices to make life
-easier for APM BIOS. event = FREEZE, flags = APM_STANDBY
-
-Apm suspend -- same as APM_STANDBY, but it we should probably avoid
-spinning down disks. event = FREEZE, flags = APM_SUSPEND
-
-System halt, reboot -- quiesce devices to make life easier for BIOS. event
-= FREEZE, flags = SYSTEM_HALT or SYSTEM_REBOOT
-
-System shutdown -- at least disks need to be spun down, or data may be
-lost. Quiesce devices, just to make life easier for BIOS. event =
-FREEZE, flags = SYSTEM_SHUTDOWN
-
-Kexec -- turn off DMAs and put hardware into some state where new
-kernel can take over. event = FREEZE, flags = KEXEC
-
-Powerdown at end of swsusp -- very similar to SYSTEM_SHUTDOWN, except wake
-may need to be enabled on some devices. This actually has at least 3
-subtypes, system can reboot, enter S4 and enter S5 at the end of
-swsusp. event = FREEZE, flags = SWSUSP and one of SYSTEM_REBOOT,
-SYSTEM_SHUTDOWN, SYSTEM_S4
-
-Suspend to ram -- put devices into low power state. event = SUSPEND,
-flags = SUSPEND_TO_RAM
-
-Freeze for swsusp snapshot -- stop DMA and interrupts. No need to put
-devices into low power mode, but you must be able to reinitialize
-device from scratch in resume method. This has two flavors, its done
-once on suspending kernel, once on resuming kernel. event = FREEZE,
-flags = DURING_SUSPEND or DURING_RESUME
-
-Device detach requested from /sys -- deinitialize device; proably same as
-SYSTEM_SHUTDOWN, I do not understand this one too much. probably event
-= FREEZE, flags = DEV_DETACH.
-
-#These are not really events sent:
-#
-#System fully on -- device is working normally; this is probably never
-#passed to suspend() method... event = ON, flags = 0
-#
-#Ready after resume -- userland is now running, again. Time to free any
-#memory you ate during prepare to suspend... event = ON, flags =
-#READY_AFTER_RESUME
-#
-
-Driver Detach Power Management
-
-The kernel now supports the ability to place a device in a low-power
-state when it is detached from its driver, which happens when its
-module is removed.
-
-Each device contains a 'detach_state' file in its sysfs directory
-which can be used to control this state. Reading from this file
-displays what the current detach state is set to. This is 0 (On) by
-default. A user may write a positive integer value to this file in the
-range of 1-4 inclusive.
-
-A value of 1-3 will indicate the device should be placed in that
-low-power state, which will cause ->suspend() to be called for that
-device. A value of 4 indicates that the device should be shutdown, so
-->shutdown() will be called for that device.
-
-The driver is responsible for reinitializing the device when the
-module is re-inserted during it's ->probe() (or equivalent) method.
-The driver core will not call any extra functions when binding the
-device to the driver.
-
-pm_message_t meaning
-
-pm_message_t has two fields. event ("major"), and flags. If driver
-does not know event code, it aborts the request, returning error. Some
-drivers may need to deal with special cases based on the actual type
-of suspend operation being done at the system level. This is why
-there are flags.
-
-Event codes are:
-
-ON -- no need to do anything except special cases like broken
-HW.
-
-# NOTIFICATION -- pretty much same as ON?
-
FREEZE -- stop DMA and interrupts, and be prepared to reinit HW from
scratch. That probably means stop accepting upstream requests, the
actual policy of what to do with them being specific to a given
git://git.onelab.eu / linux-2.6.git / blobdiff