vserver 1.9.5.x5

[linux-2.6.git] / Documentation / tipar.txt

diff --git a/Documentation/tipar.txt b/Documentation/tipar.txt
index 773b9a2..67133ba 100644 (file)
--- a/Documentation/tipar.txt
+++ b/Documentation/tipar.txt
@@ -4,7 +4,7 @@
 
 
 Author: Romain Lievin
-Homepage: http://lpg.ticalc.org/prj_dev
+Homepage: http://lpg.ticalc.org/prj_tidev/index.html
 
 
 INTRODUCTION:
@@ -12,31 +12,30 @@ INTRODUCTION:
 This is a driver for the very common home-made parallel link cable, a cable 
 designed for connecting TI8x/9x graphing calculators (handhelds) to a computer
 or workstation (Alpha, Sparc). Given that driver is built on parport, the 
-parallel port abstraction layer, this driver is independent of the platform.
+parallel port abstraction layer, this driver is architecture-independent.
 
 It can also be used with another device plugged on the same port (such as a
-ZIP drive). I have a 100MB ZIP and both of them work fine !
+ZIP drive). I have a 100MB ZIP and both of them work fine!
 
 If you need more information, please visit the 'TI drivers' homepage at the URL
 above.
 
 WHAT YOU NEED:
 
-A TI calculator of course and a program capable to communicate with your 
-calculator.
-TiLP will work for sure (since I am his developer !). yal92 may be able to use
+A TI calculator and a program capable of communicating with your calculator.
+
+TiLP will work for sure (since I am its developer!). yal92 may be able to use
 it by changing tidev for tipar (may require some hacking...).
 
 HOW TO USE IT:
 
 You must have first compiled parport support (CONFIG_PARPORT_DEV): either 
 compiled in your kernel, either as a module. 
-This driver supports the new device hierarchy (devfs).
 
-Next, (as root) from your appropriate modules directory (lib/modules/2.5.XX):
+Next, (as root):
 
        modprobe parport
-       insmod tipar.o
+       modprobe tipar
 
 If it is not already there (it usually is), create the device:
 
@@ -47,14 +46,14 @@ If it is not already there (it usually is), create the device:
 You will have to set permissions on this device to allow you to read/write
 from it:
 
-       chmod 666 /dev/tipar?
+       chmod 666 /dev/tipar[0..2]
        
 Now you are ready to run a linking program such as TiLP. Be sure to configure 
 it properly (RTFM).
        
 MODULE PARAMETERS:
 
-  You can set these with:  insmod tipar NAME=VALUE
+  You can set these with:  modprobe tipar NAME=VALUE
   There is currently no way to set these on a per-cable basis.
 
   NAME: timeout
@@ -66,11 +65,12 @@ MODULE PARAMETERS:
   NAME: delay
   TYPE: integer
   DEFAULT: 10
-  DESC: Inter-bit delay in micro-seconds. An lower value gives an higher data 
+  DESC: Inter-bit delay in micro-seconds. A lower value gives an higher data
        rate but makes transmission less reliable.
 
 These parameters can be changed at run time by any program via ioctl(2) calls 
-as listed in ./include/linux/ticable.h
+as listed in ./include/linux/ticable.h.
+
 Rather than write 50 pages describing the ioctl() and so on, it is
 perhaps more useful you look at ticables library (dev_link.c) that demonstrates
 how to use them, and demonstrates the features of the driver. This is