*/
#include <linux/kernel.h>
#include <linux/mm.h>
-#include <linux/interrupt.h>
#include <linux/init.h>
#include <asm/hardware.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-
#define IRQ_MASK 0xfe000000 /* read */
#define IRQ_MSET 0xfe000000 /* write */
#define IRQ_STAT 0xff000000 /* read */
iotable_init(ebsa110_io_desc, ARRAY_SIZE(ebsa110_io_desc));
}
-
-#define PIT_CTRL (PIT_BASE + 0x0d)
-#define PIT_T2 (PIT_BASE + 0x09)
-#define PIT_T1 (PIT_BASE + 0x05)
-#define PIT_T0 (PIT_BASE + 0x01)
-
-/*
- * This is the rate at which your MCLK signal toggles (in Hz)
- * This was measured on a 10 digit frequency counter sampling
- * over 1 second.
- */
-#define MCLK 47894000
-
-/*
- * This is the rate at which the PIT timers get clocked
- */
-#define CLKBY7 (MCLK / 7)
-
-/*
- * This is the counter value. We tick at 200Hz on this platform.
- */
-#define COUNT ((CLKBY7 + (HZ / 2)) / HZ)
-
-/*
- * Get the time offset from the system PIT. Note that if we have missed an
- * interrupt, then the PIT counter will roll over (ie, be negative).
- * This actually works out to be convenient.
- */
-static unsigned long ebsa110_gettimeoffset(void)
-{
- unsigned long offset, count;
-
- __raw_writeb(0x40, PIT_CTRL);
- count = __raw_readb(PIT_T1);
- count |= __raw_readb(PIT_T1) << 8;
-
- /*
- * If count > COUNT, make the number negative.
- */
- if (count > COUNT)
- count |= 0xffff0000;
-
- offset = COUNT;
- offset -= count;
-
- /*
- * `offset' is in units of timer counts. Convert
- * offset to units of microseconds.
- */
- offset = offset * (1000000 / HZ) / COUNT;
-
- return offset;
-}
-
-static irqreturn_t
-ebsa110_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
- u32 count;
-
- /* latch and read timer 1 */
- __raw_writeb(0x40, PIT_CTRL);
- count = __raw_readb(PIT_T1);
- count |= __raw_readb(PIT_T1) << 8;
-
- count += COUNT;
-
- __raw_writeb(count & 0xff, PIT_T1);
- __raw_writeb(count >> 8, PIT_T1);
-
- timer_tick(regs);
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction ebsa110_timer_irq = {
- .name = "EBSA110 Timer Tick",
- .flags = SA_INTERRUPT,
- .handler = ebsa110_timer_interrupt
-};
-
-/*
- * Set up timer interrupt.
- */
-static void __init ebsa110_init_time(void)
-{
- /*
- * Timer 1, mode 2, LSB/MSB
- */
- __raw_writeb(0x70, PIT_CTRL);
- __raw_writeb(COUNT & 0xff, PIT_T1);
- __raw_writeb(COUNT >> 8, PIT_T1);
-
- gettimeoffset = ebsa110_gettimeoffset;
-
- setup_irq(IRQ_EBSA110_TIMER0, &ebsa110_timer_irq);
-}
-
MACHINE_START(EBSA110, "EBSA110")
MAINTAINER("Russell King")
BOOT_MEM(0x00000000, 0xe0000000, 0xe0000000)
SOFT_REBOOT
MAPIO(ebsa110_map_io)
INITIRQ(ebsa110_init_irq)
- INITTIME(ebsa110_init_time)
MACHINE_END