#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <asm/arch/pxa2xx_spi.h>
-
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
}
-static struct irq_chip lubbock_irq_chip = {
- .name = "FPGA",
+static struct irqchip lubbock_irq_chip = {
.ack = lubbock_mask_irq,
.mask = lubbock_mask_irq,
.unmask = lubbock_unmask_irq,
},
};
-/* ADS7846 is connected through SSP ... and if your board has J5 populated,
- * you can select it to replace the ucb1400 by switching the touchscreen cable
- * (to J5) and poking board registers (as done below). Else it's only useful
- * for the temperature sensors.
- */
-static struct resource pxa_ssp_resources[] = {
- [0] = {
- .start = __PREG(SSCR0_P(1)),
- .end = __PREG(SSCR0_P(1)) + 0x14,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_SSP,
- .end = IRQ_SSP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
- .ssp_type = PXA25x_SSP,
- .clock_enable = CKEN3_SSP,
- .num_chipselect = 0,
-};
-
-static struct platform_device pxa_ssp = {
- .name = "pxa2xx-spi",
- .id = 1,
- .resource = pxa_ssp_resources,
- .num_resources = ARRAY_SIZE(pxa_ssp_resources),
- .dev = {
- .platform_data = &pxa_ssp_master_info,
- },
-};
-
-static int lubbock_ads7846_pendown_state(void)
-{
- /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
- return 0;
-}
-
-static struct ads7846_platform_data ads_info = {
- .model = 7846,
- .vref_delay_usecs = 100, /* internal, no cap */
- .get_pendown_state = lubbock_ads7846_pendown_state,
- // .x_plate_ohms = 500, /* GUESS! */
- // .y_plate_ohms = 500, /* GUESS! */
-};
-
-static void ads7846_cs(u32 command)
-{
- static const unsigned TS_nCS = 1 << 11;
- lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
-}
-
-static struct pxa2xx_spi_chip ads_hw = {
- .tx_threshold = 1,
- .rx_threshold = 2,
- .cs_control = ads7846_cs,
-};
-
-static struct spi_board_info spi_board_info[] __initdata = { {
- .modalias = "ads7846",
- .platform_data = &ads_info,
- .controller_data = &ads_hw,
- .irq = LUBBOCK_BB_IRQ,
- .max_speed_hz = 120000 /* max sample rate at 3V */
- * 26 /* command + data + overhead */,
- .bus_num = 1,
- .chip_select = 0,
-},
-};
-
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = -1,
&smc91x_device,
&lubbock_flash_device[0],
&lubbock_flash_device[1],
- &pxa_ssp,
};
static struct pxafb_mach_info sharp_lm8v31 __initdata = {
init_timer(&mmc_timer);
mmc_timer.data = (unsigned long) data;
return request_irq(LUBBOCK_SD_IRQ, lubbock_detect_int,
- IRQF_SAMPLE_RANDOM, "lubbock-sd-detect", data);
+ SA_SAMPLE_RANDOM, "lubbock-sd-detect", data);
}
static int lubbock_mci_get_ro(struct device *dev)
lubbock_flash_data[flashboot^1].name = "application-flash";
lubbock_flash_data[flashboot].name = "boot-rom";
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
-
- spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
static struct map_desc lubbock_io_desc[] __initdata = {
pxa_map_io();
iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
- /* SSP data pins */
- pxa_gpio_mode(GPIO23_SCLK_MD);
- pxa_gpio_mode(GPIO25_STXD_MD);
- pxa_gpio_mode(GPIO26_SRXD_MD);
-
/* This enables the BTUART */
pxa_gpio_mode(GPIO42_BTRXD_MD);
pxa_gpio_mode(GPIO43_BTTXD_MD);