#include <linux/config.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/dma-mapping.h>
#include <linux/sysdev.h>
#include <linux/interrupt.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
#include <asm/hardware/amba.h>
+#include <asm/hardware/amba_clcd.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
};
#endif
+/*
+ * CLCD support.
+ */
+#define SYS_CLCD_MODE_MASK (3 << 0)
+#define SYS_CLCD_MODE_5551 (0 << 0)
+#define SYS_CLCD_MODE_565 (1 << 0)
+#define SYS_CLCD_MODE_888 (2 << 0)
+#define SYS_CLCD_MODE_LT (3 << 0)
+#define SYS_CLCD_NLCDIOON (1 << 2)
+#define SYS_CLCD_VDDPOSSWITCH (1 << 3)
+#define SYS_CLCD_PWR3V5SWITCH (1 << 4)
+#define SYS_CLCD_ID_MASK (0x1f << 8)
+#define SYS_CLCD_ID_SANYO_3_8 (0x00 << 8)
+#define SYS_CLCD_ID_UNKNOWN_8_4 (0x01 << 8)
+#define SYS_CLCD_ID_EPSON_2_2 (0x02 << 8)
+#define SYS_CLCD_ID_VGA (0x1f << 8)
+
+static struct clcd_panel vga = {
+ .mode = {
+ .name = "VGA",
+ .refresh = 60,
+ .xres = 640,
+ .yres = 480,
+ .pixclock = 39721,
+ .left_margin = 40,
+ .right_margin = 24,
+ .upper_margin = 32,
+ .lower_margin = 11,
+ .hsync_len = 96,
+ .vsync_len = 2,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_BCD | TIM2_IPC,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+static struct clcd_panel sanyo_3_8_in = {
+ .mode = {
+ .name = "Sanyo QVGA",
+ .refresh = 116,
+ .xres = 320,
+ .yres = 240,
+ .pixclock = 100000,
+ .left_margin = 6,
+ .right_margin = 6,
+ .upper_margin = 5,
+ .lower_margin = 5,
+ .hsync_len = 6,
+ .vsync_len = 6,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_BCD,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+static struct clcd_panel epson_2_2_in = {
+ .mode = {
+ .name = "Epson QCIF",
+ .refresh = 390,
+ .xres = 176,
+ .yres = 220,
+ .pixclock = 62500,
+ .left_margin = 3,
+ .right_margin = 2,
+ .upper_margin = 1,
+ .lower_margin = 0,
+ .hsync_len = 3,
+ .vsync_len = 2,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+ .width = -1,
+ .height = -1,
+ .tim2 = TIM2_BCD | TIM2_IPC,
+ .cntl = CNTL_LCDTFT | CNTL_LCDVCOMP(1),
+ .bpp = 16,
+};
+
+/*
+ * Detect which LCD panel is connected, and return the appropriate
+ * clcd_panel structure. Note: we do not have any information on
+ * the required timings for the 8.4in panel, so we presently assume
+ * VGA timings.
+ */
+static struct clcd_panel *versatile_clcd_panel(void)
+{
+ unsigned long sys_clcd = IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET;
+ struct clcd_panel *panel = &vga;
+ u32 val;
+
+ val = readl(sys_clcd) & SYS_CLCD_ID_MASK;
+ if (val == SYS_CLCD_ID_SANYO_3_8)
+ panel = &sanyo_3_8_in;
+ else if (val == SYS_CLCD_ID_EPSON_2_2)
+ panel = &epson_2_2_in;
+ else if (val == SYS_CLCD_ID_VGA)
+ panel = &vga;
+ else {
+ printk(KERN_ERR "CLCD: unknown LCD panel ID 0x%08x, using VGA\n",
+ val);
+ }
+
+ return &vga;
+}
+
+/*
+ * Disable all display connectors on the interface module.
+ */
+static void versatile_clcd_disable(struct clcd_fb *fb)
+{
+ unsigned long sys_clcd = IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET;
+ u32 val;
+
+ val = readl(sys_clcd);
+ val &= ~SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
+ writel(val, sys_clcd);
+}
+
+/*
+ * Enable the relevant connector on the interface module.
+ */
+static void versatile_clcd_enable(struct clcd_fb *fb)
+{
+ unsigned long sys_clcd = IO_ADDRESS(VERSATILE_SYS_BASE) + VERSATILE_SYS_CLCD_OFFSET;
+ u32 val;
+
+ val = readl(sys_clcd);
+ val &= ~SYS_CLCD_MODE_MASK;
+
+ switch (fb->fb.var.green.length) {
+ case 5:
+#if 0
+ /*
+ * For some undocumented reason, we need to select 565 mode
+ * even when using 555 with VGA. Maybe this is only true
+ * for the VGA output and needs to be done for LCD panels?
+ * I can't get an explaination from the people who should
+ * know.
+ */
+ val |= SYS_CLCD_MODE_5551;
+ break;
+#endif
+ case 6:
+ val |= SYS_CLCD_MODE_565;
+ break;
+ case 8:
+ val |= SYS_CLCD_MODE_888;
+ break;
+ }
+
+ /*
+ * Set the MUX
+ */
+ writel(val, sys_clcd);
+
+ /*
+ * And now enable the PSUs
+ */
+ val |= SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
+ writel(val, sys_clcd);
+}
+
+static unsigned long framesize = SZ_1M;
+
+static int versatile_clcd_setup(struct clcd_fb *fb)
+{
+ dma_addr_t dma;
+
+ fb->panel = versatile_clcd_panel();
+
+ fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize,
+ &dma, GFP_KERNEL);
+ if (!fb->fb.screen_base) {
+ printk(KERN_ERR "CLCD: unable to map framebuffer\n");
+ return -ENOMEM;
+ }
+
+ fb->fb.fix.smem_start = dma;
+ fb->fb.fix.smem_len = framesize;
+
+ return 0;
+}
+
+static void versatile_clcd_remove(struct clcd_fb *fb)
+{
+ dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
+ fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+static struct clcd_board clcd_plat_data = {
+ .name = "Versatile PB",
+ .check = clcdfb_check,
+ .decode = clcdfb_decode,
+ .disable = versatile_clcd_disable,
+ .enable = versatile_clcd_enable,
+ .setup = versatile_clcd_setup,
+ .remove = versatile_clcd_remove,
+};
+
#define AMBA_DEVICE(name,busid,base,plat) \
static struct amba_device name##_device = { \
.dev = { \
/* DevChip Primecells */
AMBA_DEVICE(smc, "dev:00", SMC, NULL);
AMBA_DEVICE(mpmc, "dev:10", MPMC, NULL);
-AMBA_DEVICE(clcd, "dev:20", CLCD, NULL);
+AMBA_DEVICE(clcd, "dev:20", CLCD, &clcd_plat_data);
AMBA_DEVICE(dmac, "dev:30", DMAC, NULL);
AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
AMBA_DEVICE(wdog, "dev:e1", WATCHDOG, NULL);
git://git.onelab.eu / linux-2.6.git / blobdiff