#include <asm/cache.h>
#include <asm/thread_info.h>
#include <asm/ppc_asm.h>
-#include <asm/offsets.h>
+#include <asm/asm-offsets.h>
#ifdef CONFIG_APUS
#include <asm/amigappc.h>
#endif
-#ifdef CONFIG_PPC64BRIDGE
-#define LOAD_BAT(n, reg, RA, RB) \
- ld RA,(n*32)+0(reg); \
- ld RB,(n*32)+8(reg); \
- mtspr SPRN_IBAT##n##U,RA; \
- mtspr SPRN_IBAT##n##L,RB; \
- ld RA,(n*32)+16(reg); \
- ld RB,(n*32)+24(reg); \
- mtspr SPRN_DBAT##n##U,RA; \
- mtspr SPRN_DBAT##n##L,RB; \
-
-#else /* CONFIG_PPC64BRIDGE */
-
/* 601 only have IBAT; cr0.eq is set on 601 when using this macro */
#define LOAD_BAT(n, reg, RA, RB) \
/* see the comment for clear_bats() -- Cort */ \
mtspr SPRN_DBAT##n##U,RA; \
mtspr SPRN_DBAT##n##L,RB; \
1:
-#endif /* CONFIG_PPC64BRIDGE */
.text
.stabs "arch/ppc/kernel/",N_SO,0,0,0f
.globl __start
__start:
-/*
- * We have to do any OF calls before we map ourselves to KERNELBASE,
- * because OF may have I/O devices mapped into that area
- * (particularly on CHRP).
- */
mr r31,r3 /* save parameters */
mr r30,r4
mr r29,r5
*/
bl early_init
-/*
- * On POWER4, we first need to tweak some CPU configuration registers
- * like real mode cache inhibit or exception base
- */
-#ifdef CONFIG_POWER4
- bl __970_cpu_preinit
-#endif /* CONFIG_POWER4 */
-
#ifdef CONFIG_APUS
/* On APUS the __va/__pa constants need to be set to the correct
* values before continuing.
*/
bl mmu_off
__after_mmu_off:
-#ifndef CONFIG_POWER4
bl clear_bats
bl flush_tlbs
#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
bl setup_disp_bat
#endif
-#else /* CONFIG_POWER4 */
- bl reloc_offset
- bl initial_mm_power4
-#endif /* CONFIG_POWER4 */
/*
* Call setup_cpu for CPU 0 and initialize 6xx Idle
bl reloc_offset
bl init_idle_6xx
#endif /* CONFIG_6xx */
-#ifdef CONFIG_POWER4
- bl reloc_offset
- bl init_idle_power4
-#endif /* CONFIG_POWER4 */
#ifndef CONFIG_APUS
/*
* We need to run with _start at physical address 0.
- * On CHRP, we are loaded at 0x10000 since OF on CHRP uses
- * the exception vectors at 0 (and therefore this copy
- * overwrites OF's exception vectors with our own).
* If the MMU is already turned on, we copy stuff to KERNELBASE,
* otherwise we copy it to 0.
*/
/* System reset */
/* core99 pmac starts the seconary here by changing the vector, and
- putting it back to what it was (UnknownException) when done. */
+ putting it back to what it was (unknown_exception) when done. */
#if defined(CONFIG_GEMINI) && defined(CONFIG_SMP)
. = 0x100
b __secondary_start_gemini
#else
- EXCEPTION(0x100, Reset, UnknownException, EXC_XFER_STD)
+ EXCEPTION(0x100, Reset, unknown_exception, EXC_XFER_STD)
#endif
/* Machine check */
-/*
- * On CHRP, this is complicated by the fact that we could get a
- * machine check inside RTAS, and we have no guarantee that certain
- * critical registers will have the values we expect. The set of
- * registers that might have bad values includes all the GPRs
- * and all the BATs. We indicate that we are in RTAS by putting
- * a non-zero value, the address of the exception frame to use,
- * in SPRG2. The machine check handler checks SPRG2 and uses its
- * value if it is non-zero. If we ever needed to free up SPRG2,
- * we could use a field in the thread_info or thread_struct instead.
- * (Other exception handlers assume that r1 is a valid kernel stack
- * pointer when we take an exception from supervisor mode.)
- * -- paulus.
- */
. = 0x200
mtspr SPRN_SPRG0,r10
mtspr SPRN_SPRG1,r11
mfcr r10
-#ifdef CONFIG_PPC_CHRP
- mfspr r11,SPRN_SPRG2
- cmpwi 0,r11,0
- bne 7f
-#endif /* CONFIG_PPC_CHRP */
EXCEPTION_PROLOG_1
7: EXCEPTION_PROLOG_2
addi r3,r1,STACK_FRAME_OVERHEAD
-#ifdef CONFIG_PPC_CHRP
- mfspr r4,SPRN_SPRG2
- cmpwi cr1,r4,0
- bne cr1,1f
-#endif
- EXC_XFER_STD(0x200, MachineCheckException)
-#ifdef CONFIG_PPC_CHRP
-1: b machine_check_in_rtas
-#endif
+ EXC_XFER_STD(0x200, machine_check_exception)
/* Data access exception. */
. = 0x300
-#ifdef CONFIG_PPC64BRIDGE
- b DataAccess
-DataAccessCont:
-#else
DataAccess:
EXCEPTION_PROLOG
-#endif /* CONFIG_PPC64BRIDGE */
mfspr r10,SPRN_DSISR
andis. r0,r10,0xa470 /* weird error? */
bne 1f /* if not, try to put a PTE */
mfspr r4,SPRN_DAR
EXC_XFER_EE_LITE(0x300, handle_page_fault)
-#ifdef CONFIG_PPC64BRIDGE
-/* SLB fault on data access. */
- . = 0x380
- b DataSegment
-#endif /* CONFIG_PPC64BRIDGE */
-
/* Instruction access exception. */
. = 0x400
-#ifdef CONFIG_PPC64BRIDGE
- b InstructionAccess
-InstructionAccessCont:
-#else
InstructionAccess:
EXCEPTION_PROLOG
-#endif /* CONFIG_PPC64BRIDGE */
andis. r0,r9,0x4000 /* no pte found? */
beq 1f /* if so, try to put a PTE */
li r3,0 /* into the hash table */
mr r5,r9
EXC_XFER_EE_LITE(0x400, handle_page_fault)
-#ifdef CONFIG_PPC64BRIDGE
-/* SLB fault on instruction access. */
- . = 0x480
- b InstructionSegment
-#endif /* CONFIG_PPC64BRIDGE */
-
/* External interrupt */
EXCEPTION(0x500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE)
mfspr r5,SPRN_DSISR
stw r5,_DSISR(r11)
addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_EE(0x600, AlignmentException)
+ EXC_XFER_EE(0x600, alignment_exception)
/* Program check exception */
- EXCEPTION(0x700, ProgramCheck, ProgramCheckException, EXC_XFER_STD)
+ EXCEPTION(0x700, ProgramCheck, program_check_exception, EXC_XFER_STD)
/* Floating-point unavailable */
. = 0x800
EXCEPTION_PROLOG
bne load_up_fpu /* if from user, just load it up */
addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_EE_LITE(0x800, KernelFP)
+ EXC_XFER_EE_LITE(0x800, kernel_fp_unavailable_exception)
/* Decrementer */
EXCEPTION(0x900, Decrementer, timer_interrupt, EXC_XFER_LITE)
- EXCEPTION(0xa00, Trap_0a, UnknownException, EXC_XFER_EE)
- EXCEPTION(0xb00, Trap_0b, UnknownException, EXC_XFER_EE)
+ EXCEPTION(0xa00, Trap_0a, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0xb00, Trap_0b, unknown_exception, EXC_XFER_EE)
/* System call */
. = 0xc00
EXC_XFER_EE_LITE(0xc00, DoSyscall)
/* Single step - not used on 601 */
- EXCEPTION(0xd00, SingleStep, SingleStepException, EXC_XFER_STD)
- EXCEPTION(0xe00, Trap_0e, UnknownException, EXC_XFER_EE)
+ EXCEPTION(0xd00, SingleStep, single_step_exception, EXC_XFER_STD)
+ EXCEPTION(0xe00, Trap_0e, unknown_exception, EXC_XFER_EE)
/*
* The Altivec unavailable trap is at 0x0f20. Foo.
Trap_0f:
EXCEPTION_PROLOG
addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_EE(0xf00, UnknownException)
+ EXC_XFER_EE(0xf00, unknown_exception)
/*
* Handle TLB miss for instruction on 603/603e.
rfi
#ifndef CONFIG_ALTIVEC
-#define AltivecAssistException UnknownException
+#define altivec_assist_exception unknown_exception
#endif
- EXCEPTION(0x1300, Trap_13, InstructionBreakpoint, EXC_XFER_EE)
+ EXCEPTION(0x1300, Trap_13, instruction_breakpoint_exception, EXC_XFER_EE)
EXCEPTION(0x1400, SMI, SMIException, EXC_XFER_EE)
- EXCEPTION(0x1500, Trap_15, UnknownException, EXC_XFER_EE)
-#ifdef CONFIG_POWER4
- EXCEPTION(0x1600, Trap_16, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1700, Trap_17, AltivecAssistException, EXC_XFER_EE)
- EXCEPTION(0x1800, Trap_18, TAUException, EXC_XFER_STD)
-#else /* !CONFIG_POWER4 */
- EXCEPTION(0x1600, Trap_16, AltivecAssistException, EXC_XFER_EE)
+ EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1600, Trap_16, altivec_assist_exception, EXC_XFER_EE)
EXCEPTION(0x1700, Trap_17, TAUException, EXC_XFER_STD)
- EXCEPTION(0x1800, Trap_18, UnknownException, EXC_XFER_EE)
-#endif /* CONFIG_POWER4 */
- EXCEPTION(0x1900, Trap_19, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1a00, Trap_1a, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1b00, Trap_1b, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1c00, Trap_1c, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1d00, Trap_1d, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1e00, Trap_1e, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x1f00, Trap_1f, UnknownException, EXC_XFER_EE)
+ EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1a00, Trap_1a, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1b00, Trap_1b, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1c00, Trap_1c, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1d00, Trap_1d, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1e00, Trap_1e, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x1f00, Trap_1f, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x2000, RunMode, RunModeException, EXC_XFER_EE)
- EXCEPTION(0x2100, Trap_21, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2200, Trap_22, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2300, Trap_23, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2400, Trap_24, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2500, Trap_25, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2600, Trap_26, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2700, Trap_27, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2800, Trap_28, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2900, Trap_29, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2a00, Trap_2a, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2b00, Trap_2b, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2c00, Trap_2c, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2d00, Trap_2d, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2e00, Trap_2e, UnknownException, EXC_XFER_EE)
- EXCEPTION(0x2f00, MOLTrampoline, UnknownException, EXC_XFER_EE_LITE)
+ EXCEPTION(0x2100, Trap_21, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2200, Trap_22, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2300, Trap_23, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2400, Trap_24, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2500, Trap_25, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2600, Trap_26, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2700, Trap_27, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2800, Trap_28, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2900, Trap_29, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2a00, Trap_2a, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2b00, Trap_2b, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2c00, Trap_2c, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2d00, Trap_2d, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2e00, Trap_2e, unknown_exception, EXC_XFER_EE)
+ EXCEPTION(0x2f00, MOLTrampoline, unknown_exception, EXC_XFER_EE_LITE)
.globl mol_trampoline
.set mol_trampoline, i0x2f00
#ifdef CONFIG_ALTIVEC
bne load_up_altivec /* if from user, just load it up */
#endif /* CONFIG_ALTIVEC */
- EXC_XFER_EE_LITE(0xf20, AltivecUnavailException)
-
-#ifdef CONFIG_PPC64BRIDGE
-DataAccess:
- EXCEPTION_PROLOG
- b DataAccessCont
-
-InstructionAccess:
- EXCEPTION_PROLOG
- b InstructionAccessCont
-
-DataSegment:
- EXCEPTION_PROLOG
- addi r3,r1,STACK_FRAME_OVERHEAD
- mfspr r4,SPRN_DAR
- stw r4,_DAR(r11)
- EXC_XFER_STD(0x380, UnknownException)
-
-InstructionSegment:
- EXCEPTION_PROLOG
addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_STD(0x480, UnknownException)
-#endif /* CONFIG_PPC64BRIDGE */
+ EXC_XFER_EE_LITE(0xf20, altivec_unavailable_exception)
#ifdef CONFIG_ALTIVEC
/* Note that the AltiVec support is closely modeled after the FP
beq 1f
add r4,r4,r6
addi r4,r4,THREAD /* want THREAD of last_task_used_altivec */
- SAVE_32VR(0,r10,r4)
+ SAVE_32VRS(0,r10,r4)
mfvscr vr0
li r10,THREAD_VSCR
stvx vr0,r10,r4
stw r4,THREAD_USED_VR(r5)
lvx vr0,r10,r5
mtvscr vr0
- REST_32VR(0,r10,r5)
+ REST_32VRS(0,r10,r5)
#ifndef CONFIG_SMP
subi r4,r5,THREAD
sub r4,r4,r6
addi r3,r3,THREAD /* want THREAD of task */
lwz r5,PT_REGS(r3)
cmpwi 0,r5,0
- SAVE_32VR(0, r4, r3)
+ SAVE_32VRS(0, r4, r3)
mfvscr vr0
li r4,THREAD_VSCR
stvx vr0,r4,r3
copy_and_flush:
addi r5,r5,-4
addi r6,r6,-4
-4: li r0,L1_CACHE_LINE_SIZE/4
+4: li r0,L1_CACHE_BYTES/4
mtctr r0
3: addi r6,r6,4 /* copy a cache line */
lwzx r0,r6,r4
andc r4,r4,r3
mtspr SPRN_HID0,r4
sync
- bl gemini_prom_init
b __secondary_start
#endif /* CONFIG_GEMINI */
- .globl __secondary_start_psurge
-__secondary_start_psurge:
- li r24,1 /* cpu # */
- b __secondary_start_psurge99
- .globl __secondary_start_psurge2
-__secondary_start_psurge2:
- li r24,2 /* cpu # */
- b __secondary_start_psurge99
- .globl __secondary_start_psurge3
-__secondary_start_psurge3:
- li r24,3 /* cpu # */
- b __secondary_start_psurge99
-__secondary_start_psurge99:
- /* we come in here with IR=0 and DR=1, and DBAT 0
+
+ .globl __secondary_start_pmac_0
+__secondary_start_pmac_0:
+ /* NB the entries for cpus 0, 1, 2 must each occupy 8 bytes. */
+ li r24,0
+ b 1f
+ li r24,1
+ b 1f
+ li r24,2
+ b 1f
+ li r24,3
+1:
+ /* on powersurge, we come in here with IR=0 and DR=1, and DBAT 0
set to map the 0xf0000000 - 0xffffffff region */
mfmsr r0
rlwinm r0,r0,0,28,26 /* clear DR (0x10) */
.globl __secondary_start
__secondary_start:
-#ifdef CONFIG_PPC64BRIDGE
- mfmsr r0
- clrldi r0,r0,1 /* make sure it's in 32-bit mode */
- SYNC
- MTMSRD(r0)
- isync
-#endif
/* Copy some CPU settings from CPU 0 */
bl __restore_cpu_setup
lis r3,-KERNELBASE@h
mr r4,r24
- bl identify_cpu
bl call_setup_cpu /* Call setup_cpu for this CPU */
#ifdef CONFIG_6xx
lis r3,-KERNELBASE@h
bl init_idle_6xx
#endif /* CONFIG_6xx */
-#ifdef CONFIG_POWER4
- lis r3,-KERNELBASE@h
- bl init_idle_power4
-#endif /* CONFIG_POWER4 */
/* get current_thread_info and current */
lis r1,secondary_ti@ha
* Those generic dummy functions are kept for CPUs not
* included in CONFIG_6xx
*/
-_GLOBAL(__setup_cpu_power3)
- blr
-_GLOBAL(__setup_cpu_generic)
- blr
-
-#if !defined(CONFIG_6xx) && !defined(CONFIG_POWER4)
+#if !defined(CONFIG_6xx)
_GLOBAL(__save_cpu_setup)
blr
_GLOBAL(__restore_cpu_setup)
blr
-#endif /* !defined(CONFIG_6xx) && !defined(CONFIG_POWER4) */
+#endif /* !defined(CONFIG_6xx) */
/*
tophys(r6,r6)
lwz r6,_SDR1@l(r6)
mtspr SPRN_SDR1,r6
-#ifdef CONFIG_PPC64BRIDGE
- /* clear the ASR so we only use the pseudo-segment registers. */
- li r6,0
- mtasr r6
-#endif /* CONFIG_PPC64BRIDGE */
li r0,16 /* load up segment register values */
mtctr r0 /* for context 0 */
lis r3,0x2000 /* Ku = 1, VSID = 0 */
addi r3,r3,0x111 /* increment VSID */
addis r4,r4,0x1000 /* address of next segment */
bdnz 3b
-#ifndef CONFIG_POWER4
+
/* Load the BAT registers with the values set up by MMU_init.
MMU_init takes care of whether we're on a 601 or not. */
mfpvr r3
LOAD_BAT(1,r3,r4,r5)
LOAD_BAT(2,r3,r4,r5)
LOAD_BAT(3,r3,r4,r5)
-#endif /* CONFIG_POWER4 */
+
blr
/*
li r4,0
isync
3:
-#ifdef CONFIG_PPC64BRIDGE
- slbie r4
-#endif /* CONFIG_PPC64BRIDGE */
mtsrin r3,r4
addi r3,r3,0x111 /* next VSID */
rlwinm r3,r3,0,8,3 /* clear out any overflow from VSID field */
sync
RFI
-#ifndef CONFIG_POWER4
/*
* Use the first pair of BAT registers to map the 1st 16MB
* of RAM to KERNELBASE. From this point on we can't safely
*/
initial_bats:
lis r11,KERNELBASE@h
-#ifndef CONFIG_PPC64BRIDGE
mfspr r9,SPRN_PVR
rlwinm r9,r9,16,16,31 /* r9 = 1 for 601, 4 for 604 */
cmpwi 0,r9,1
mtspr SPRN_IBAT1L,r10
isync
blr
-#endif /* CONFIG_PPC64BRIDGE */
4: tophys(r8,r11)
#ifdef CONFIG_SMP
ori r11,r11,BL_256M<<2|0x2 /* set up BAT registers for 604 */
#endif /* CONFIG_APUS */
-#ifdef CONFIG_PPC64BRIDGE
- /* clear out the high 32 bits in the BAT */
- clrldi r11,r11,32
- clrldi r8,r8,32
-#endif /* CONFIG_PPC64BRIDGE */
mtspr SPRN_DBAT0L,r8 /* N.B. 6xx (not 601) have valid */
mtspr SPRN_DBAT0U,r11 /* bit in upper BAT register */
mtspr SPRN_IBAT0L,r8
#endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */
-#else /* CONFIG_POWER4 */
-/*
- * Load up the SDR1 and segment register values now
- * since we don't have the BATs.
- * Also make sure we are running in 32-bit mode.
- */
-
-initial_mm_power4:
- addis r14,r3,_SDR1@ha /* get the value from _SDR1 */
- lwz r14,_SDR1@l(r14) /* assume hash table below 4GB */
- mtspr SPRN_SDR1,r14
- slbia
- lis r4,0x2000 /* set pseudo-segment reg 12 */
- ori r5,r4,0x0ccc
- mtsr 12,r5
-#if 0
- ori r5,r4,0x0888 /* set pseudo-segment reg 8 */
- mtsr 8,r5 /* (for access to serial port) */
-#endif
-#ifdef CONFIG_BOOTX_TEXT
- ori r5,r4,0x0999 /* set pseudo-segment reg 9 */
- mtsr 9,r5 /* (for access to screen) */
-#endif
- mfmsr r0
- clrldi r0,r0,1
- sync
- mtmsr r0
- isync
- blr
-
-#endif /* CONFIG_POWER4 */
-
#ifdef CONFIG_8260
/* Jump into the system reset for the rom.
* We first disable the MMU, and then jump to the ROM reset address.