This commit was manufactured by cvs2svn to create tag

[linux-2.6.git] / arch / sh / drivers / pci / pci-sh7751.c

diff --git a/arch/sh/drivers/pci/pci-sh7751.c b/arch/sh/drivers/pci/pci-sh7751.c
index b2bb729..e53823e 100644 (file)
--- a/arch/sh/drivers/pci/pci-sh7751.c
+++ b/arch/sh/drivers/pci/pci-sh7751.c
@@ -31,7 +31,6 @@
 #include "pci-sh7751.h"
 
 static unsigned int pci_probe = PCI_PROBE_CONF1;
-extern int pci_fixup_pcic(void);
 
 /*
  * Direct access to PCI hardware...
@@ -75,8 +74,7 @@ static int sh7751_pci_read(struct pci_bus *bus, unsigned int devfn,
 }
 
 /* 
- * Since SH7751 only does 32bit access we'll have to do a read,
- * mask,write operation.
+ * Since SH7751 only does 32bit access we'll have to do a read,mask,write operation.  
  * We'll allow an odd byte offset, though it should be illegal.
  */ 
 static int sh7751_pci_write(struct pci_bus *bus, unsigned int devfn,
@@ -158,7 +156,6 @@ static int __init pci_check_direct(void)
  *  Handle bus scanning and fixups ....
  */
 
-#if !defined(CONFIG_SH_HS7751RVOIP) && !defined(CONFIG_SH_RTS7751R2D)
 static void __init pci_fixup_ide_bases(struct pci_dev *d)
 {
        int i;
@@ -177,13 +174,11 @@ static void __init pci_fixup_ide_bases(struct pci_dev *d)
                }
        }
 }
-#endif
+
 
 /* Add future fixups here... */
 struct pci_fixup pcibios_fixups[] = {
-#if !defined(CONFIG_SH_HS7751RVOIP) && !defined(CONFIG_SH_RTS7751R2D)
        { PCI_FIXUP_HEADER,     PCI_ANY_ID,     PCI_ANY_ID,     pci_fixup_ide_bases },
-#endif
        { 0 }
 };
 
@@ -266,19 +261,19 @@ int __init sh7751_pcic_init(struct sh7751_pci_address_map *map)
        outl(word, PCI_REG(SH7751_PCICLKR));
 
        /*
-        * This code is unused for some boards as it is done in the
-        * bootloader and doing it here means the MAC addresses loaded
-        * by the bootloader get lost.
+        * XXX: This code is unused for the SnapGear boards as it is done in
+        * the bootloader and doing it here means the MAC addresses loaded by
+        * the bootloader get lost.
         */
-       if (!(map->flags & SH7751_PCIC_NO_RESET)) {
-               /* toggle PCI reset pin */
-               word = SH7751_PCICR_PREFIX | SH7751_PCICR_PRST;
-               outl(word,PCI_REG(SH7751_PCICR));
-               /* Wait for a long time... not 1 sec. but long enough */
-               mdelay(100);
-               word = SH7751_PCICR_PREFIX;
-               outl(word,PCI_REG(SH7751_PCICR));
-       }
+#ifndef CONFIG_SH_SECUREEDGE5410
+       /* toggle PCI reset pin */
+       word = SH7751_PCICR_PREFIX | SH7751_PCICR_PRST;
+       outl(word,PCI_REG(SH7751_PCICR));    
+       /* Wait for a long time... not 1 sec. but long enough */
+       mdelay(100);
+       word = SH7751_PCICR_PREFIX;
+       outl(word,PCI_REG(SH7751_PCICR)); 
+#endif
        
        /* set the command/status bits to:
         * Wait Cycle Control + Parity Enable + Bus Master +
@@ -369,10 +364,6 @@ int __init sh7751_pcic_init(struct sh7751_pci_address_map *map)
         * DMA interrupts...
         */
         
-#ifdef CONFIG_SH_RTS7751R2D
-       pci_fixup_pcic();
-#endif
-
        /* SH7751 init done, set central function init complete */
        /* use round robin mode to stop a device starving/overruning */
        word = SH7751_PCICR_PREFIX | SH7751_PCICR_CFIN | SH7751_PCICR_ARBM;