bool
default y
-config UID16
- bool
- default y
-
config HIGHMEM
bool
default y
menu "General machine setup"
-config VT
- bool
- select INPUT
- default y
- ---help---
- If you say Y here, you will get support for terminal devices with
- display and keyboard devices. These are called "virtual" because you
- can run several virtual terminals (also called virtual consoles) on
- one physical terminal. This is rather useful, for example one
- virtual terminal can collect system messages and warnings, another
- one can be used for a text-mode user session, and a third could run
- an X session, all in parallel. Switching between virtual terminals
- is done with certain key combinations, usually Alt-<function key>.
-
- The setterm command ("man setterm") can be used to change the
- properties (such as colors or beeping) of a virtual terminal. The
- man page console_codes(4) ("man console_codes") contains the special
- character sequences that can be used to change those properties
- directly. The fonts used on virtual terminals can be changed with
- the setfont ("man setfont") command and the key bindings are defined
- with the loadkeys ("man loadkeys") command.
-
- You need at least one virtual terminal device in order to make use
- of your keyboard and monitor. Therefore, only people configuring an
- embedded system would want to say N here in order to save some
- memory; the only way to log into such a system is then via a serial
- or network connection.
-
- If unsure, say Y, or else you won't be able to do much with your new
- shiny Linux system :-)
-
-config VT_CONSOLE
- bool
- default y
- ---help---
- The system console is the device which receives all kernel messages
- and warnings and which allows logins in single user mode. If you
- answer Y here, a virtual terminal (the device used to interact with
- a physical terminal) can be used as system console. This is the most
- common mode of operations, so you should say Y here unless you want
- the kernel messages be output only to a serial port (in which case
- you should say Y to "Console on serial port", below).
-
- If you do say Y here, by default the currently visible virtual
- terminal (/dev/tty0) will be used as system console. You can change
- that with a kernel command line option such as "console=tty3" which
- would use the third virtual terminal as system console. (Try "man
- bootparam" or see the documentation of your boot loader (lilo or
- loadlin) about how to pass options to the kernel at boot time.)
-
- If unsure, say Y.
-
-config HW_CONSOLE
- bool
- default y
-
config SMP
bool "Symmetric multi-processing support (does not work on sun4/sun4c)"
- depends on BROKEN
---help---
This enables support for systems with more than one CPU. If you have
a system with only one CPU, say N. If you have a system with more
depends on SMP
default "32"
+config SPARC
+ bool
+ default y
+
# Identify this as a Sparc32 build
config SPARC32
bool
config RWSEM_XCHGADD_ALGORITHM
bool
+config GENERIC_FIND_NEXT_BIT
+ bool
+ default y
+
+config GENERIC_HWEIGHT
+ bool
+ default y
+
config GENERIC_CALIBRATE_DELAY
bool
default y
+config ARCH_MAY_HAVE_PC_FDC
+ bool
+ default y
+
config SUN_PM
bool
default y
Only choose N if you know in advance that you will not need to modify
OpenPROM settings on the running system.
+config SPARC_LED
+ tristate "Sun4m LED driver"
+ help
+ This driver toggles the front-panel LED on sun4m systems
+ in a user-specifyable manner. It's state can be probed
+ by reading /proc/led and it's blinking mode can be changed
+ via writes to /proc/led
+
source "fs/Kconfig.binfmt"
config SUNOS_EMUL
want to run SunOS binaries on an Ultra you must also say Y to
"Kernel support for 32-bit a.out binaries" above.
-source "drivers/parport/Kconfig"
-
-config PRINTER
- tristate "Parallel printer support"
- depends on PARPORT
- ---help---
- If you intend to attach a printer to the parallel port of your Linux
- box (as opposed to using a serial printer; if the connector at the
- printer has 9 or 25 holes ["female"], then it's serial), say Y.
- Also read the Printing-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- It is possible to share one parallel port among several devices
- (e.g. printer and ZIP drive) and it is safe to compile the
- corresponding drivers into the kernel. If you want to compile this
- driver as a module however, choose M here and read
- <file:Documentation/parport.txt>. The module will be called lp.
-
- If you have several parallel ports, you can specify which ports to
- use with the "lp" kernel command line option. (Try "man bootparam"
- or see the documentation of your boot loader (silo) about how to pass
- options to the kernel at boot time.) The syntax of the "lp" command
- line option can be found in <file:drivers/char/lp.c>.
-
- If you have more than 8 printers, you need to increase the LP_NO
- macro in lp.c and the PARPORT_MAX macro in parport.h.
+source "mm/Kconfig"
endmenu
-source "drivers/base/Kconfig"
-
-source "drivers/video/Kconfig"
-
-source "drivers/mtd/Kconfig"
+source "net/Kconfig"
-source "drivers/serial/Kconfig"
+source "drivers/Kconfig"
if !SUN4
source "drivers/sbus/char/Kconfig"
endif
-source "drivers/block/Kconfig"
-
-# Don't frighten a common SBus user
-if PCI
-
-source "drivers/ide/Kconfig"
-
-endif
-
-source "drivers/isdn/Kconfig"
-
-source "drivers/scsi/Kconfig"
-
-source "drivers/fc4/Kconfig"
-
-source "drivers/md/Kconfig"
-
-source "net/Kconfig"
-
# This one must be before the filesystem configs. -DaveM
menu "Unix98 PTY support"
endmenu
-source "drivers/input/Kconfig"
-
source "fs/Kconfig"
-source "sound/Kconfig"
-
-source "drivers/usb/Kconfig"
-
-source "drivers/infiniband/Kconfig"
-
-source "drivers/char/watchdog/Kconfig"
-
source "arch/sparc/Kconfig.debug"
source "kernel/vserver/Kconfig"
git://git.onelab.eu / linux-2.6.git / blobdiff