--- /dev/null
+/*
+ * ata_piix.c - Intel PATA/SATA controllers
+ *
+ * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Please ALWAYS copy linux-ide@vger.kernel.org
+ * on emails.
+ *
+ *
+ * Copyright 2003-2005 Red Hat Inc
+ * Copyright 2003-2005 Jeff Garzik
+ *
+ *
+ * Copyright header from piix.c:
+ *
+ * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * libata documentation is available via 'make {ps|pdf}docs',
+ * as Documentation/DocBook/libata.*
+ *
+ * Hardware documentation available at http://developer.intel.com/
+ *
+ * Documentation
+ * Publically available from Intel web site. Errata documentation
+ * is also publically available. As an aide to anyone hacking on this
+ * driver the list of errata that are relevant is below, going back to
+ * PIIX4. Older device documentation is now a bit tricky to find.
+ *
+ * The chipsets all follow very much the same design. The orginal Triton
+ * series chipsets do _not_ support independant device timings, but this
+ * is fixed in Triton II. With the odd mobile exception the chips then
+ * change little except in gaining more modes until SATA arrives. This
+ * driver supports only the chips with independant timing (that is those
+ * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
+ * for the early chip drivers.
+ *
+ * Errata of note:
+ *
+ * Unfixable
+ * PIIX4 errata #9 - Only on ultra obscure hw
+ * ICH3 errata #13 - Not observed to affect real hw
+ * by Intel
+ *
+ * Things we must deal with
+ * PIIX4 errata #10 - BM IDE hang with non UDMA
+ * (must stop/start dma to recover)
+ * 440MX errata #15 - As PIIX4 errata #10
+ * PIIX4 errata #15 - Must not read control registers
+ * during a PIO transfer
+ * 440MX errata #13 - As PIIX4 errata #15
+ * ICH2 errata #21 - DMA mode 0 doesn't work right
+ * ICH0/1 errata #55 - As ICH2 errata #21
+ * ICH2 spec c #9 - Extra operations needed to handle
+ * drive hotswap [NOT YET SUPPORTED]
+ * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
+ * and must be dword aligned
+ * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
+ *
+ * Should have been BIOS fixed:
+ * 450NX: errata #19 - DMA hangs on old 450NX
+ * 450NX: errata #20 - DMA hangs on old 450NX
+ * 450NX: errata #25 - Corruption with DMA on old 450NX
+ * ICH3 errata #15 - IDE deadlock under high load
+ * (BIOS must set dev 31 fn 0 bit 23)
+ * ICH3 errata #18 - Don't use native mode
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "ata_piix"
+#define DRV_VERSION "2.00ac7"
+
+enum {
+ PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
+ ICH5_PMR = 0x90, /* port mapping register */
+ ICH5_PCS = 0x92, /* port control and status */
+ PIIX_SCC = 0x0A, /* sub-class code register */
+
+ PIIX_FLAG_SCR = (1 << 26), /* SCR available */
+ PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */
+ PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
+
+ PIIX_PATA_FLAGS = ATA_FLAG_SLAVE_POSS,
+ PIIX_SATA_FLAGS = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
+
+ /* combined mode. if set, PATA is channel 0.
+ * if clear, PATA is channel 1.
+ */
+ PIIX_PORT_ENABLED = (1 << 0),
+ PIIX_PORT_PRESENT = (1 << 4),
+
+ PIIX_80C_PRI = (1 << 5) | (1 << 4),
+ PIIX_80C_SEC = (1 << 7) | (1 << 6),
+
+ /* controller IDs */
+ piix_pata_33 = 0, /* PIIX3 or 4 at 33Mhz */
+ ich_pata_33 = 1, /* ICH up to UDMA 33 only */
+ ich_pata_66 = 2, /* ICH up to 66 Mhz */
+ ich_pata_100 = 3, /* ICH up to UDMA 100 */
+ ich_pata_133 = 4, /* ICH up to UDMA 133 */
+ ich5_sata = 5,
+ ich6_sata = 6,
+ ich6_sata_ahci = 7,
+ ich6m_sata_ahci = 8,
+ ich8_sata_ahci = 9,
+
+ /* constants for mapping table */
+ P0 = 0, /* port 0 */
+ P1 = 1, /* port 1 */
+ P2 = 2, /* port 2 */
+ P3 = 3, /* port 3 */
+ IDE = -1, /* IDE */
+ NA = -2, /* not avaliable */
+ RV = -3, /* reserved */
+
+ PIIX_AHCI_DEVICE = 6,
+};
+
+struct piix_map_db {
+ const u32 mask;
+ const u16 port_enable;
+ const int map[][4];
+};
+
+struct piix_host_priv {
+ const int *map;
+};
+
+static int piix_init_one (struct pci_dev *pdev,
+ const struct pci_device_id *ent);
+static void piix_host_stop(struct ata_host *host);
+static void piix_pata_error_handler(struct ata_port *ap);
+static void ich_pata_error_handler(struct ata_port *ap);
+static void piix_sata_error_handler(struct ata_port *ap);
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+
+static unsigned int in_module_init = 1;
+
+static const struct pci_device_id piix_pci_tbl[] = {
+#ifdef ATA_ENABLE_PATA
+ /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */
+ /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */
+ { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+ { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* Intel PIIX4 */
+ { 0x8086, 0x7199, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+ /* Intel PIIX4 */
+ { 0x8086, 0x7601, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+ /* Intel PIIX */
+ { 0x8086, 0x84CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
+ /* Intel ICH (i810, i815, i840) UDMA 66*/
+ { 0x8086, 0x2411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_66 },
+ /* Intel ICH0 : UDMA 33*/
+ { 0x8086, 0x2421, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_33 },
+ /* Intel ICH2M */
+ { 0x8086, 0x244A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* Intel ICH2 (i810E2, i845, 850, 860) UDMA 100 */
+ { 0x8086, 0x244B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* Intel ICH3M */
+ { 0x8086, 0x248A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* Intel ICH3 (E7500/1) UDMA 100 */
+ { 0x8086, 0x248B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* Intel ICH4 (i845GV, i845E, i852, i855) UDMA 100 */
+ { 0x8086, 0x24CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ { 0x8086, 0x24CB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* Intel ICH5 */
+ { 0x8086, 0x24DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
+ /* C-ICH (i810E2) */
+ { 0x8086, 0x245B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* ESB (855GME/875P + 6300ESB) UDMA 100 */
+ { 0x8086, 0x25A2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* ICH6 (and 6) (i915) UDMA 100 */
+ { 0x8086, 0x266F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+ /* ICH7/7-R (i945, i975) UDMA 100*/
+ { 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
+ { 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
+#endif
+
+ /* NOTE: The following PCI ids must be kept in sync with the
+ * list in drivers/pci/quirks.c.
+ */
+
+ /* 82801EB (ICH5) */
+ { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 82801EB (ICH5) */
+ { 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 6300ESB (ICH5 variant with broken PCS present bits) */
+ { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 6300ESB pretending RAID */
+ { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
+ /* 82801FB/FW (ICH6/ICH6W) */
+ { 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
+ /* 82801FR/FRW (ICH6R/ICH6RW) */
+ { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */
+ { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+ /* 82801GB/GR/GH (ICH7, identical to ICH6) */
+ { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* 2801GBM/GHM (ICH7M, identical to ICH6M) */
+ { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
+ /* Enterprise Southbridge 2 (631xESB/632xESB) */
+ { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ /* SATA Controller 1 IDE (ICH8) */
+ { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller 2 IDE (ICH8) */
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* Mobile SATA Controller IDE (ICH8M) */
+ { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+
+ { } /* terminate list */
+};
+
+static struct pci_driver piix_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = piix_pci_tbl,
+ .probe = piix_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+#endif
+};
+
+static struct scsi_host_template piix_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+#ifdef CONFIG_PM
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
+#endif
+};
+
+static const struct ata_port_operations piix_pata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = piix_set_piomode,
+ .set_dmamode = piix_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_pata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
+};
+
+static const struct ata_port_operations ich_pata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = piix_set_piomode,
+ .set_dmamode = ich_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ich_pata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
+};
+
+static const struct ata_port_operations piix_sata_ops = {
+ .port_disable = ata_port_disable,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = piix_sata_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = piix_host_stop,
+};
+
+static const struct piix_map_db ich5_map_db = {
+ .mask = 0x7,
+ .port_enable = 0x3,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 000b */
+ { P1, NA, P0, NA }, /* 001b */
+ { RV, RV, RV, RV },
+ { RV, RV, RV, RV },
+ { P0, P1, IDE, IDE }, /* 100b */
+ { P1, P0, IDE, IDE }, /* 101b */
+ { IDE, IDE, P0, P1 }, /* 110b */
+ { IDE, IDE, P1, P0 }, /* 111b */
+ },
+};
+
+static const struct piix_map_db ich6_map_db = {
+ .mask = 0x3,
+ .port_enable = 0xf,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, P1, P3 }, /* 00b */
+ { IDE, IDE, P1, P3 }, /* 01b */
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich6m_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x5,
+
+ /* Map 01b isn't specified in the doc but some notebooks use
+ * it anyway. MAP 01b have been spotted on both ICH6M and
+ * ICH7M.
+ */
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, RV, RV }, /* 00b */
+ { IDE, IDE, P1, P3 }, /* 01b */
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db ich8_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x3,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, P2, P1, P3 }, /* 00b (hardwired when in AHCI) */
+ { RV, RV, RV, RV },
+ { IDE, IDE, NA, NA }, /* 10b (IDE mode) */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db *piix_map_db_table[] = {
+ [ich5_sata] = &ich5_map_db,
+ [ich6_sata] = &ich6_map_db,
+ [ich6_sata_ahci] = &ich6_map_db,
+ [ich6m_sata_ahci] = &ich6m_map_db,
+ [ich8_sata_ahci] = &ich8_map_db,
+};
+
+static struct ata_port_info piix_port_info[] = {
+ /* piix_pata_33: 0: PIIX3 or 4 at 33MHz */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .udma_mask = ATA_UDMA_MASK_40C,
+ .port_ops = &piix_pata_ops,
+ },
+
+ /* ich_pata_33: 1 ICH0 - ICH at 33Mhz*/
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS,
+ .pio_mask = 0x1f, /* pio 0-4 */
+ .mwdma_mask = 0x06, /* Check: maybe 0x07 */
+ .udma_mask = ATA_UDMA2, /* UDMA33 */
+ .port_ops = &ich_pata_ops,
+ },
+ /* ich_pata_66: 2 ICH controllers up to 66MHz */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS,
+ .pio_mask = 0x1f, /* pio 0-4 */
+ .mwdma_mask = 0x06, /* MWDMA0 is broken on chip */
+ .udma_mask = ATA_UDMA4,
+ .port_ops = &ich_pata_ops,
+ },
+
+ /* ich_pata_100: 3 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+ .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .port_ops = &ich_pata_ops,
+ },
+
+ /* ich_pata_133: 4 ICH with full UDMA6 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
+ .pio_mask = 0x1f, /* pio 0-4 */
+ .mwdma_mask = 0x06, /* Check: maybe 0x07 */
+ .udma_mask = ATA_UDMA6, /* UDMA133 */
+ .port_ops = &ich_pata_ops,
+ },
+
+ /* ich5_sata: 5 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6_sata: 6 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6_sata_ahci: 7 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich6m_sata_ahci: 8 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+ /* ich8_sata_ahci: 9 */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x7f, /* udma0-6 */
+ .port_ops = &piix_sata_ops,
+ },
+
+};
+
+static struct pci_bits piix_enable_bits[] = {
+ { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
+ { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
+};
+
+MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik");
+MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+struct ich_laptop {
+ u16 device;
+ u16 subvendor;
+ u16 subdevice;
+};
+
+/*
+ * List of laptops that use short cables rather than 80 wire
+ */
+
+static const struct ich_laptop ich_laptop[] = {
+ /* devid, subvendor, subdev */
+ { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
+ /* end marker */
+ { 0, }
+};
+
+/**
+ * piix_pata_cbl_detect - Probe host controller cable detect info
+ * @ap: Port for which cable detect info is desired
+ *
+ * Read 80c cable indicator from ATA PCI device's PCI config
+ * register. This register is normally set by firmware (BIOS).
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void ich_pata_cbl_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ const struct ich_laptop *lap = &ich_laptop[0];
+ u8 tmp, mask;
+
+ /* no 80c support in host controller? */
+ if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0)
+ goto cbl40;
+
+ /* Check for specials - Acer Aspire 5602WLMi */
+ while (lap->device) {
+ if (lap->device == pdev->device &&
+ lap->subvendor == pdev->subsystem_vendor &&
+ lap->subdevice == pdev->subsystem_device) {
+ ap->cbl = ATA_CBL_PATA40_SHORT;
+ return;
+ }
+ lap++;
+ }
+
+ /* check BIOS cable detect results */
+ mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
+ pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
+ if ((tmp & mask) == 0)
+ goto cbl40;
+
+ ap->cbl = ATA_CBL_PATA80;
+ return;
+
+cbl40:
+ ap->cbl = ATA_CBL_PATA40;
+}
+
+/**
+ * piix_pata_prereset - prereset for PATA host controller
+ * @ap: Target port
+ *
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static int piix_pata_prereset(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
+ return -ENOENT;
+
+ ap->cbl = ATA_CBL_PATA40;
+ return ata_std_prereset(ap);
+}
+
+static void piix_pata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, piix_pata_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+
+/**
+ * ich_pata_prereset - prereset for PATA host controller
+ * @ap: Target port
+ *
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static int ich_pata_prereset(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) {
+ ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
+ ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
+ return 0;
+ }
+
+ ich_pata_cbl_detect(ap);
+
+ return ata_std_prereset(ap);
+}
+
+static void ich_pata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ich_pata_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+static void piix_sata_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+/**
+ * piix_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int is_slave = (adev->devno != 0);
+ unsigned int master_port= ap->port_no ? 0x42 : 0x40;
+ unsigned int slave_port = 0x44;
+ u16 master_data;
+ u8 slave_data;
+ u8 udma_enable;
+ int control = 0;
+
+ /*
+ * See Intel Document 298600-004 for the timing programing rules
+ * for ICH controllers.
+ */
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ if (pio >= 2)
+ control |= 1; /* TIME1 enable */
+ if (ata_pio_need_iordy(adev))
+ control |= 2; /* IE enable */
+
+ /* Intel specifies that the PPE functionality is for disk only */
+ if (adev->class == ATA_DEV_ATA)
+ control |= 4; /* PPE enable */
+
+ pci_read_config_word(dev, master_port, &master_data);
+ if (is_slave) {
+ /* Enable SITRE (seperate slave timing register) */
+ master_data |= 0x4000;
+ /* enable PPE1, IE1 and TIME1 as needed */
+ master_data |= (control << 4);
+ pci_read_config_byte(dev, slave_port, &slave_data);
+ slave_data &= (ap->port_no ? 0x0f : 0xf0);
+ /* Load the timing nibble for this slave */
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ } else {
+ /* Master keeps the bits in a different format */
+ master_data &= 0xccf8;
+ /* Enable PPE, IE and TIME as appropriate */
+ master_data |= control;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ pci_write_config_word(dev, master_port, master_data);
+ if (is_slave)
+ pci_write_config_byte(dev, slave_port, slave_data);
+
+ /* Ensure the UDMA bit is off - it will be turned back on if
+ UDMA is selected */
+
+ if (ap->udma_mask) {
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+ udma_enable &= ~(1 << (2 * ap->port_no + adev->devno));
+ pci_write_config_byte(dev, 0x48, udma_enable);
+ }
+}
+
+/**
+ * do_pata_set_dmamode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Drive in question
+ * @udma: udma mode, 0 - 6
+ * @isich: set if the chip is an ICH device
+ *
+ * Set UDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, int isich)
+{
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ u8 master_port = ap->port_no ? 0x42 : 0x40;
+ u16 master_data;
+ u8 speed = adev->dma_mode;
+ int devid = adev->devno + 2 * ap->port_no;
+ u8 udma_enable;
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ pci_read_config_word(dev, master_port, &master_data);
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+
+ if (speed >= XFER_UDMA_0) {
+ unsigned int udma = adev->dma_mode - XFER_UDMA_0;
+ u16 udma_timing;
+ u16 ideconf;
+ int u_clock, u_speed;
+
+ /*
+ * UDMA is handled by a combination of clock switching and
+ * selection of dividers
+ *
+ * Handy rule: Odd modes are UDMATIMx 01, even are 02
+ * except UDMA0 which is 00
+ */
+ u_speed = min(2 - (udma & 1), udma);
+ if (udma == 5)
+ u_clock = 0x1000; /* 100Mhz */
+ else if (udma > 2)
+ u_clock = 1; /* 66Mhz */
+ else
+ u_clock = 0; /* 33Mhz */
+
+ udma_enable |= (1 << devid);
+
+ /* Load the CT/RP selection */
+ pci_read_config_word(dev, 0x4A, &udma_timing);
+ udma_timing &= ~(3 << (4 * devid));
+ udma_timing |= u_speed << (4 * devid);
+ pci_write_config_word(dev, 0x4A, udma_timing);
+
+ if (isich) {
+ /* Select a 33/66/100Mhz clock */
+ pci_read_config_word(dev, 0x54, &ideconf);
+ ideconf &= ~(0x1001 << devid);
+ ideconf |= u_clock << devid;
+ /* For ICH or later we should set bit 10 for better
+ performance (WR_PingPong_En) */
+ pci_write_config_word(dev, 0x54, ideconf);
+ }
+ } else {
+ /*
+ * MWDMA is driven by the PIO timings. We must also enable
+ * IORDY unconditionally along with TIME1. PPE has already
+ * been set when the PIO timing was set.
+ */
+ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
+ unsigned int control;
+ u8 slave_data;
+ const unsigned int needed_pio[3] = {
+ XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+ };
+ int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+ control = 3; /* IORDY|TIME1 */
+
+ /* If the drive MWDMA is faster than it can do PIO then
+ we must force PIO into PIO0 */
+
+ if (adev->pio_mode < needed_pio[mwdma])
+ /* Enable DMA timing only */
+ control |= 8; /* PIO cycles in PIO0 */
+
+ if (adev->devno) { /* Slave */
+ master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
+ master_data |= control << 4;
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= (0x0F + 0xE1 * ap->port_no);
+ /* Load the matching timing */
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ pci_write_config_byte(dev, 0x44, slave_data);
+ } else { /* Master */
+ master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
+ and master timing bits */
+ master_data |= control;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, master_port, master_data);
+ }
+ /* Don't scribble on 0x48 if the controller does not support UDMA */
+ if (ap->udma_mask)
+ pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+/**
+ * piix_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set MW/UDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ do_pata_set_dmamode(ap, adev, 0);
+}
+
+/**
+ * ich_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set MW/UDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ do_pata_set_dmamode(ap, adev, 1);
+}
+
+#define AHCI_PCI_BAR 5
+#define AHCI_GLOBAL_CTL 0x04
+#define AHCI_ENABLE (1 << 31)
+static int piix_disable_ahci(struct pci_dev *pdev)
+{
+ void __iomem *mmio;
+ u32 tmp;
+ int rc = 0;
+
+ /* BUG: pci_enable_device has not yet been called. This
+ * works because this device is usually set up by BIOS.
+ */
+
+ if (!pci_resource_start(pdev, AHCI_PCI_BAR) ||
+ !pci_resource_len(pdev, AHCI_PCI_BAR))
+ return 0;
+
+ mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64);
+ if (!mmio)
+ return -ENOMEM;
+
+ tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ if (tmp & AHCI_ENABLE) {
+ tmp &= ~AHCI_ENABLE;
+ writel(tmp, mmio + AHCI_GLOBAL_CTL);
+
+ tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ if (tmp & AHCI_ENABLE)
+ rc = -EIO;
+ }
+
+ pci_iounmap(pdev, mmio);
+ return rc;
+}
+
+/**
+ * piix_check_450nx_errata - Check for problem 450NX setup
+ * @ata_dev: the PCI device to check
+ *
+ * Check for the present of 450NX errata #19 and errata #25. If
+ * they are found return an error code so we can turn off DMA
+ */
+
+static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
+{
+ struct pci_dev *pdev = NULL;
+ u16 cfg;
+ u8 rev;
+ int no_piix_dma = 0;
+
+ while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
+ {
+ /* Look for 450NX PXB. Check for problem configurations
+ A PCI quirk checks bit 6 already */
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+ pci_read_config_word(pdev, 0x41, &cfg);
+ /* Only on the original revision: IDE DMA can hang */
+ if (rev == 0x00)
+ no_piix_dma = 1;
+ /* On all revisions below 5 PXB bus lock must be disabled for IDE */
+ else if (cfg & (1<<14) && rev < 5)
+ no_piix_dma = 2;
+ }
+ if (no_piix_dma)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n");
+ if (no_piix_dma == 2)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
+ return no_piix_dma;
+}
+
+static void __devinit piix_init_pcs(struct pci_dev *pdev,
+ struct ata_port_info *pinfo,
+ const struct piix_map_db *map_db)
+{
+ u16 pcs, new_pcs;
+
+ pci_read_config_word(pdev, ICH5_PCS, &pcs);
+
+ new_pcs = pcs | map_db->port_enable;
+
+ if (new_pcs != pcs) {
+ DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs);
+ pci_write_config_word(pdev, ICH5_PCS, new_pcs);
+ msleep(150);
+ }
+}
+
+static void __devinit piix_init_sata_map(struct pci_dev *pdev,
+ struct ata_port_info *pinfo,
+ const struct piix_map_db *map_db)
+{
+ struct piix_host_priv *hpriv = pinfo[0].private_data;
+ const unsigned int *map;
+ int i, invalid_map = 0;
+ u8 map_value;
+
+ pci_read_config_byte(pdev, ICH5_PMR, &map_value);
+
+ map = map_db->map[map_value & map_db->mask];
+
+ dev_printk(KERN_INFO, &pdev->dev, "MAP [");
+ for (i = 0; i < 4; i++) {
+ switch (map[i]) {
+ case RV:
+ invalid_map = 1;
+ printk(" XX");
+ break;
+
+ case NA:
+ printk(" --");
+ break;
+
+ case IDE:
+ WARN_ON((i & 1) || map[i + 1] != IDE);
+ pinfo[i / 2] = piix_port_info[ich_pata_100];
+ pinfo[i / 2].private_data = hpriv;
+ i++;
+ printk(" IDE IDE");
+ break;
+
+ default:
+ printk(" P%d", map[i]);
+ if (i & 1)
+ pinfo[i / 2].flags |= ATA_FLAG_SLAVE_POSS;
+ break;
+ }
+ }
+ printk(" ]\n");
+
+ if (invalid_map)
+ dev_printk(KERN_ERR, &pdev->dev,
+ "invalid MAP value %u\n", map_value);
+
+ hpriv->map = map;
+}
+
+/**
+ * piix_init_one - Register PIIX ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in piix_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer. We probe for combined mode (sigh),
+ * and then hand over control to libata, for it to do the rest.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ struct ata_port_info port_info[2];
+ struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
+ struct piix_host_priv *hpriv;
+ unsigned long port_flags;
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ /* no hotplugging support (FIXME) */
+ if (!in_module_init)
+ return -ENODEV;
+
+ hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv)
+ return -ENOMEM;
+
+ port_info[0] = piix_port_info[ent->driver_data];
+ port_info[1] = piix_port_info[ent->driver_data];
+ port_info[0].private_data = hpriv;
+ port_info[1].private_data = hpriv;
+
+ port_flags = port_info[0].flags;
+
+ if (port_flags & PIIX_FLAG_AHCI) {
+ u8 tmp;
+ pci_read_config_byte(pdev, PIIX_SCC, &tmp);
+ if (tmp == PIIX_AHCI_DEVICE) {
+ int rc = piix_disable_ahci(pdev);
+ if (rc)
+ return rc;
+ }
+ }
+
+ /* Initialize SATA map */
+ if (port_flags & ATA_FLAG_SATA) {
+ piix_init_sata_map(pdev, port_info,
+ piix_map_db_table[ent->driver_data]);
+ piix_init_pcs(pdev, port_info,
+ piix_map_db_table[ent->driver_data]);
+ }
+
+ /* On ICH5, some BIOSen disable the interrupt using the
+ * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
+ * On ICH6, this bit has the same effect, but only when
+ * MSI is disabled (and it is disabled, as we don't use
+ * message-signalled interrupts currently).
+ */
+ if (port_flags & PIIX_FLAG_CHECKINTR)
+ pci_intx(pdev, 1);
+
+ if (piix_check_450nx_errata(pdev)) {
+ /* This writes into the master table but it does not
+ really matter for this errata as we will apply it to
+ all the PIIX devices on the board */
+ port_info[0].mwdma_mask = 0;
+ port_info[0].udma_mask = 0;
+ port_info[1].mwdma_mask = 0;
+ port_info[1].udma_mask = 0;
+ }
+ return ata_pci_init_one(pdev, ppinfo, 2);
+}
+
+static void piix_host_stop(struct ata_host *host)
+{
+ struct piix_host_priv *hpriv = host->private_data;
+
+ ata_host_stop(host);
+
+ kfree(hpriv);
+}
+
+static int __init piix_init(void)
+{
+ int rc;
+
+ DPRINTK("pci_register_driver\n");
+ rc = pci_register_driver(&piix_pci_driver);
+ if (rc)
+ return rc;
+
+ in_module_init = 0;
+
+ DPRINTK("done\n");
+ return 0;
+}
+
+static void __exit piix_exit(void)
+{
+ pci_unregister_driver(&piix_pci_driver);
+}
+
+module_init(piix_init);
+module_exit(piix_exit);
git://git.onelab.eu / linux-2.6.git / blobdiff