--- /dev/null
+/*
+ * Promise PATA TX2/TX4/TX2000/133 IDE driver for pdc20268 to pdc20277.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Ported to libata by:
+ * Albert Lee <albertcc@tw.ibm.com> IBM Corporation
+ *
+ * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 1999 Promise Technology, Inc.
+ *
+ * Author: Frank Tiernan (frankt@promise.com)
+ * Released under terms of General Public License
+ *
+ *
+ * libata documentation is available via 'make {ps|pdf}docs',
+ * as Documentation/DocBook/libata.*
+ *
+ * Hardware information only available under NDA.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_cmnd.h>
+#include <linux/libata.h>
+#include <asm/io.h>
+
+#define DRV_NAME "pata_pdc2027x"
+#define DRV_VERSION "0.74-ac5"
+#undef PDC_DEBUG
+
+#ifdef PDC_DEBUG
+#define PDPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#else
+#define PDPRINTK(fmt, args...)
+#endif
+
+enum {
+ PDC_UDMA_100 = 0,
+ PDC_UDMA_133 = 1,
+
+ PDC_100_MHZ = 100000000,
+ PDC_133_MHZ = 133333333,
+
+ PDC_SYS_CTL = 0x1100,
+ PDC_ATA_CTL = 0x1104,
+ PDC_GLOBAL_CTL = 0x1108,
+ PDC_CTCR0 = 0x110C,
+ PDC_CTCR1 = 0x1110,
+ PDC_BYTE_COUNT = 0x1120,
+ PDC_PLL_CTL = 0x1202,
+};
+
+static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void pdc2027x_remove_one(struct pci_dev *pdev);
+static void pdc2027x_error_handler(struct ata_port *ap);
+static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev);
+static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev);
+static void pdc2027x_post_set_mode(struct ata_port *ap);
+static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc);
+
+/*
+ * ATA Timing Tables based on 133MHz controller clock.
+ * These tables are only used when the controller is in 133MHz clock.
+ * If the controller is in 100MHz clock, the ASIC hardware will
+ * set the timing registers automatically when "set feature" command
+ * is issued to the device. However, if the controller clock is 133MHz,
+ * the following tables must be used.
+ */
+static struct pdc2027x_pio_timing {
+ u8 value0, value1, value2;
+} pdc2027x_pio_timing_tbl [] = {
+ { 0xfb, 0x2b, 0xac }, /* PIO mode 0 */
+ { 0x46, 0x29, 0xa4 }, /* PIO mode 1 */
+ { 0x23, 0x26, 0x64 }, /* PIO mode 2 */
+ { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */
+ { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */
+};
+
+static struct pdc2027x_mdma_timing {
+ u8 value0, value1;
+} pdc2027x_mdma_timing_tbl [] = {
+ { 0xdf, 0x5f }, /* MDMA mode 0 */
+ { 0x6b, 0x27 }, /* MDMA mode 1 */
+ { 0x69, 0x25 }, /* MDMA mode 2 */
+};
+
+static struct pdc2027x_udma_timing {
+ u8 value0, value1, value2;
+} pdc2027x_udma_timing_tbl [] = {
+ { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */
+ { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */
+ { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */
+ { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */
+ { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */
+ { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */
+ { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */
+};
+
+static const struct pci_device_id pdc2027x_pci_tbl[] = {
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), PDC_UDMA_100 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), PDC_UDMA_100 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), PDC_UDMA_133 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), PDC_UDMA_133 },
+
+ { } /* terminate list */
+};
+
+static struct pci_driver pdc2027x_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = pdc2027x_pci_tbl,
+ .probe = pdc2027x_init_one,
+ .remove = __devexit_p(pdc2027x_remove_one),
+};
+
+static struct scsi_host_template pdc2027x_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct ata_port_operations pdc2027x_pata100_ops = {
+ .port_disable = ata_port_disable,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .check_atapi_dma = pdc2027x_check_atapi_dma,
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_mmio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = pdc2027x_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_pci_host_stop,
+};
+
+static struct ata_port_operations pdc2027x_pata133_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = pdc2027x_set_piomode,
+ .set_dmamode = pdc2027x_set_dmamode,
+ .post_set_mode = pdc2027x_post_set_mode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .check_atapi_dma = pdc2027x_check_atapi_dma,
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_mmio_data_xfer,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = pdc2027x_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_pci_host_stop,
+};
+
+static struct ata_port_info pdc2027x_port_info[] = {
+ /* PDC_UDMA_100 */
+ {
+ .sht = &pdc2027x_sht,
+ .flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
+ ATA_FLAG_MMIO,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .port_ops = &pdc2027x_pata100_ops,
+ },
+ /* PDC_UDMA_133 */
+ {
+ .sht = &pdc2027x_sht,
+ .flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
+ ATA_FLAG_MMIO,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA6, /* udma0-6 */
+ .port_ops = &pdc2027x_pata133_ops,
+ },
+};
+
+MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Albert Lee");
+MODULE_DESCRIPTION("libata driver module for Promise PDC20268 to PDC20277");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+MODULE_DEVICE_TABLE(pci, pdc2027x_pci_tbl);
+
+/**
+ * port_mmio - Get the MMIO address of PDC2027x extended registers
+ * @ap: Port
+ * @offset: offset from mmio base
+ */
+static inline void __iomem *port_mmio(struct ata_port *ap, unsigned int offset)
+{
+ return ap->host->mmio_base + ap->port_no * 0x100 + offset;
+}
+
+/**
+ * dev_mmio - Get the MMIO address of PDC2027x extended registers
+ * @ap: Port
+ * @adev: device
+ * @offset: offset from mmio base
+ */
+static inline void __iomem *dev_mmio(struct ata_port *ap, struct ata_device *adev, unsigned int offset)
+{
+ u8 adj = (adev->devno) ? 0x08 : 0x00;
+ return port_mmio(ap, offset) + adj;
+}
+
+/**
+ * pdc2027x_pata_cbl_detect - Probe host controller cable detect info
+ * @ap: Port for which cable detect info is desired
+ *
+ * Read 80c cable indicator from Promise extended register.
+ * This register is latched when the system is reset.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void pdc2027x_cbl_detect(struct ata_port *ap)
+{
+ u32 cgcr;
+
+ /* check cable detect results */
+ cgcr = readl(port_mmio(ap, PDC_GLOBAL_CTL));
+ if (cgcr & (1 << 26))
+ goto cbl40;
+
+ PDPRINTK("No cable or 80-conductor cable on port %d\n", ap->port_no);
+
+ ap->cbl = ATA_CBL_PATA80;
+ return;
+
+cbl40:
+ printk(KERN_INFO DRV_NAME ": 40-conductor cable detected on port %d\n", ap->port_no);
+ ap->cbl = ATA_CBL_PATA40;
+ ap->udma_mask &= ATA_UDMA_MASK_40C;
+}
+
+/**
+ * pdc2027x_port_enabled - Check PDC ATA control register to see whether the port is enabled.
+ * @ap: Port to check
+ */
+static inline int pdc2027x_port_enabled(struct ata_port *ap)
+{
+ return readb(port_mmio(ap, PDC_ATA_CTL)) & 0x02;
+}
+
+/**
+ * pdc2027x_prereset - prereset for PATA host controller
+ * @ap: Target port
+ *
+ * Probeinit including cable detection.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static int pdc2027x_prereset(struct ata_port *ap)
+{
+ /* Check whether port enabled */
+ if (!pdc2027x_port_enabled(ap))
+ return -ENOENT;
+ pdc2027x_cbl_detect(ap);
+ return ata_std_prereset(ap);
+}
+
+/**
+ * pdc2027x_error_handler - Perform reset on PATA port and classify
+ * @ap: Port to reset
+ *
+ * Reset PATA phy and classify attached devices.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void pdc2027x_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, pdc2027x_prereset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ * pdc2027x_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port to configure
+ * @adev: um
+ * @pio: PIO mode, 0 - 4
+ *
+ * Set PIO mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ u32 ctcr0, ctcr1;
+
+ PDPRINTK("adev->pio_mode[%X]\n", adev->pio_mode);
+
+ /* Sanity check */
+ if (pio > 4) {
+ printk(KERN_ERR DRV_NAME ": Unknown pio mode [%d] ignored\n", pio);
+ return;
+
+ }
+
+ /* Set the PIO timing registers using value table for 133MHz */
+ PDPRINTK("Set pio regs... \n");
+
+ ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0));
+ ctcr0 &= 0xffff0000;
+ ctcr0 |= pdc2027x_pio_timing_tbl[pio].value0 |
+ (pdc2027x_pio_timing_tbl[pio].value1 << 8);
+ writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
+
+ ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+ ctcr1 &= 0x00ffffff;
+ ctcr1 |= (pdc2027x_pio_timing_tbl[pio].value2 << 24);
+ writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
+
+ PDPRINTK("Set pio regs done\n");
+
+ PDPRINTK("Set to pio mode[%u] \n", pio);
+}
+
+/**
+ * pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings
+ * @ap: Port to configure
+ * @adev: um
+ * @udma: udma mode, XFER_UDMA_0 to XFER_UDMA_6
+ *
+ * Set UDMA mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int dma_mode = adev->dma_mode;
+ u32 ctcr0, ctcr1;
+
+ if ((dma_mode >= XFER_UDMA_0) &&
+ (dma_mode <= XFER_UDMA_6)) {
+ /* Set the UDMA timing registers with value table for 133MHz */
+ unsigned int udma_mode = dma_mode & 0x07;
+
+ if (dma_mode == XFER_UDMA_2) {
+ /*
+ * Turn off tHOLD.
+ * If tHOLD is '1', the hardware will add half clock for data hold time.
+ * This code segment seems to be no effect. tHOLD will be overwritten below.
+ */
+ ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+ writel(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1));
+ }
+
+ PDPRINTK("Set udma regs... \n");
+
+ ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+ ctcr1 &= 0xff000000;
+ ctcr1 |= pdc2027x_udma_timing_tbl[udma_mode].value0 |
+ (pdc2027x_udma_timing_tbl[udma_mode].value1 << 8) |
+ (pdc2027x_udma_timing_tbl[udma_mode].value2 << 16);
+ writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
+
+ PDPRINTK("Set udma regs done\n");
+
+ PDPRINTK("Set to udma mode[%u] \n", udma_mode);
+
+ } else if ((dma_mode >= XFER_MW_DMA_0) &&
+ (dma_mode <= XFER_MW_DMA_2)) {
+ /* Set the MDMA timing registers with value table for 133MHz */
+ unsigned int mdma_mode = dma_mode & 0x07;
+
+ PDPRINTK("Set mdma regs... \n");
+ ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0));
+
+ ctcr0 &= 0x0000ffff;
+ ctcr0 |= (pdc2027x_mdma_timing_tbl[mdma_mode].value0 << 16) |
+ (pdc2027x_mdma_timing_tbl[mdma_mode].value1 << 24);
+
+ writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
+ PDPRINTK("Set mdma regs done\n");
+
+ PDPRINTK("Set to mdma mode[%u] \n", mdma_mode);
+ } else {
+ printk(KERN_ERR DRV_NAME ": Unknown dma mode [%u] ignored\n", dma_mode);
+ }
+}
+
+/**
+ * pdc2027x_post_set_mode - Set the timing registers back to correct values.
+ * @ap: Port to configure
+ *
+ * The pdc2027x hardware will look at "SET FEATURES" and change the timing registers
+ * automatically. The values set by the hardware might be incorrect, under 133Mhz PLL.
+ * This function overwrites the possibly incorrect values set by the hardware to be correct.
+ */
+static void pdc2027x_post_set_mode(struct ata_port *ap)
+{
+ int i;
+
+ for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ struct ata_device *dev = &ap->device[i];
+
+ if (ata_dev_enabled(dev)) {
+
+ pdc2027x_set_piomode(ap, dev);
+
+ /*
+ * Enable prefetch if the device support PIO only.
+ */
+ if (dev->xfer_shift == ATA_SHIFT_PIO) {
+ u32 ctcr1 = readl(dev_mmio(ap, dev, PDC_CTCR1));
+ ctcr1 |= (1 << 25);
+ writel(ctcr1, dev_mmio(ap, dev, PDC_CTCR1));
+
+ PDPRINTK("Turn on prefetch\n");
+ } else {
+ pdc2027x_set_dmamode(ap, dev);
+ }
+ }
+ }
+}
+
+/**
+ * pdc2027x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command
+ * @qc: Metadata associated with taskfile to check
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ *
+ * RETURNS: 0 when ATAPI DMA can be used
+ * 1 otherwise
+ */
+static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ struct scsi_cmnd *cmd = qc->scsicmd;
+ u8 *scsicmd = cmd->cmnd;
+ int rc = 1; /* atapi dma off by default */
+
+ /*
+ * This workaround is from Promise's GPL driver.
+ * If ATAPI DMA is used for commands not in the
+ * following white list, say MODE_SENSE and REQUEST_SENSE,
+ * pdc2027x might hit the irq lost problem.
+ */
+ switch (scsicmd[0]) {
+ case READ_10:
+ case WRITE_10:
+ case READ_12:
+ case WRITE_12:
+ case READ_6:
+ case WRITE_6:
+ case 0xad: /* READ_DVD_STRUCTURE */
+ case 0xbe: /* READ_CD */
+ /* ATAPI DMA is ok */
+ rc = 0;
+ break;
+ default:
+ ;
+ }
+
+ return rc;
+}
+
+/**
+ * pdc_read_counter - Read the ctr counter
+ * @probe_ent: for the port address
+ */
+
+static long pdc_read_counter(struct ata_probe_ent *probe_ent)
+{
+ long counter;
+ int retry = 1;
+ u32 bccrl, bccrh, bccrlv, bccrhv;
+
+retry:
+ bccrl = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff;
+ bccrh = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
+ rmb();
+
+ /* Read the counter values again for verification */
+ bccrlv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff;
+ bccrhv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
+ rmb();
+
+ counter = (bccrh << 15) | bccrl;
+
+ PDPRINTK("bccrh [%X] bccrl [%X]\n", bccrh, bccrl);
+ PDPRINTK("bccrhv[%X] bccrlv[%X]\n", bccrhv, bccrlv);
+
+ /*
+ * The 30-bit decreasing counter are read by 2 pieces.
+ * Incorrect value may be read when both bccrh and bccrl are changing.
+ * Ex. When 7900 decrease to 78FF, wrong value 7800 might be read.
+ */
+ if (retry && !(bccrh == bccrhv && bccrl >= bccrlv)) {
+ retry--;
+ PDPRINTK("rereading counter\n");
+ goto retry;
+ }
+
+ return counter;
+}
+
+/**
+ * adjust_pll - Adjust the PLL input clock in Hz.
+ *
+ * @pdc_controller: controller specific information
+ * @probe_ent: For the port address
+ * @pll_clock: The input of PLL in HZ
+ */
+static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx)
+{
+
+ u16 pll_ctl;
+ long pll_clock_khz = pll_clock / 1000;
+ long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ;
+ long ratio = pout_required / pll_clock_khz;
+ int F, R;
+
+ /* Sanity check */
+ if (unlikely(pll_clock_khz < 5000L || pll_clock_khz > 70000L)) {
+ printk(KERN_ERR DRV_NAME ": Invalid PLL input clock %ldkHz, give up!\n", pll_clock_khz);
+ return;
+ }
+
+#ifdef PDC_DEBUG
+ PDPRINTK("pout_required is %ld\n", pout_required);
+
+ /* Show the current clock value of PLL control register
+ * (maybe already configured by the firmware)
+ */
+ pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL);
+
+ PDPRINTK("pll_ctl[%X]\n", pll_ctl);
+#endif
+
+ /*
+ * Calculate the ratio of F, R and OD
+ * POUT = (F + 2) / (( R + 2) * NO)
+ */
+ if (ratio < 8600L) { /* 8.6x */
+ /* Using NO = 0x01, R = 0x0D */
+ R = 0x0d;
+ } else if (ratio < 12900L) { /* 12.9x */
+ /* Using NO = 0x01, R = 0x08 */
+ R = 0x08;
+ } else if (ratio < 16100L) { /* 16.1x */
+ /* Using NO = 0x01, R = 0x06 */
+ R = 0x06;
+ } else if (ratio < 64000L) { /* 64x */
+ R = 0x00;
+ } else {
+ /* Invalid ratio */
+ printk(KERN_ERR DRV_NAME ": Invalid ratio %ld, give up!\n", ratio);
+ return;
+ }
+
+ F = (ratio * (R+2)) / 1000 - 2;
+
+ if (unlikely(F < 0 || F > 127)) {
+ /* Invalid F */
+ printk(KERN_ERR DRV_NAME ": F[%d] invalid!\n", F);
+ return;
+ }
+
+ PDPRINTK("F[%d] R[%d] ratio*1000[%ld]\n", F, R, ratio);
+
+ pll_ctl = (R << 8) | F;
+
+ PDPRINTK("Writing pll_ctl[%X]\n", pll_ctl);
+
+ writew(pll_ctl, probe_ent->mmio_base + PDC_PLL_CTL);
+ readw(probe_ent->mmio_base + PDC_PLL_CTL); /* flush */
+
+ /* Wait the PLL circuit to be stable */
+ mdelay(30);
+
+#ifdef PDC_DEBUG
+ /*
+ * Show the current clock value of PLL control register
+ * (maybe configured by the firmware)
+ */
+ pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL);
+
+ PDPRINTK("pll_ctl[%X]\n", pll_ctl);
+#endif
+
+ return;
+}
+
+/**
+ * detect_pll_input_clock - Detect the PLL input clock in Hz.
+ * @probe_ent: for the port address
+ * Ex. 16949000 on 33MHz PCI bus for pdc20275.
+ * Half of the PCI clock.
+ */
+static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent)
+{
+ u32 scr;
+ long start_count, end_count;
+ long pll_clock;
+
+ /* Read current counter value */
+ start_count = pdc_read_counter(probe_ent);
+
+ /* Start the test mode */
+ scr = readl(probe_ent->mmio_base + PDC_SYS_CTL);
+ PDPRINTK("scr[%X]\n", scr);
+ writel(scr | (0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL);
+ readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */
+
+ /* Let the counter run for 100 ms. */
+ mdelay(100);
+
+ /* Read the counter values again */
+ end_count = pdc_read_counter(probe_ent);
+
+ /* Stop the test mode */
+ scr = readl(probe_ent->mmio_base + PDC_SYS_CTL);
+ PDPRINTK("scr[%X]\n", scr);
+ writel(scr & ~(0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL);
+ readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */
+
+ /* calculate the input clock in Hz */
+ pll_clock = (start_count - end_count) * 10;
+
+ PDPRINTK("start[%ld] end[%ld] \n", start_count, end_count);
+ PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock);
+
+ return pll_clock;
+}
+
+/**
+ * pdc_hardware_init - Initialize the hardware.
+ * @pdev: instance of pci_dev found
+ * @pdc_controller: controller specific information
+ * @pe: for the port address
+ */
+static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx)
+{
+ long pll_clock;
+
+ /*
+ * Detect PLL input clock rate.
+ * On some system, where PCI bus is running at non-standard clock rate.
+ * Ex. 25MHz or 40MHz, we have to adjust the cycle_time.
+ * The pdc20275 controller employs PLL circuit to help correct timing registers setting.
+ */
+ pll_clock = pdc_detect_pll_input_clock(pe);
+
+ if (pll_clock < 0) /* counter overflow? Try again. */
+ pll_clock = pdc_detect_pll_input_clock(pe);
+
+ dev_printk(KERN_INFO, &pdev->dev, "PLL input clock %ld kHz\n", pll_clock/1000);
+
+ /* Adjust PLL control register */
+ pdc_adjust_pll(pe, pll_clock, board_idx);
+
+ return 0;
+}
+
+/**
+ * pdc_ata_setup_port - setup the mmio address
+ * @port: ata ioports to setup
+ * @base: base address
+ */
+static void pdc_ata_setup_port(struct ata_ioports *port, unsigned long base)
+{
+ port->cmd_addr =
+ port->data_addr = base;
+ port->feature_addr =
+ port->error_addr = base + 0x05;
+ port->nsect_addr = base + 0x0a;
+ port->lbal_addr = base + 0x0f;
+ port->lbam_addr = base + 0x10;
+ port->lbah_addr = base + 0x15;
+ port->device_addr = base + 0x1a;
+ port->command_addr =
+ port->status_addr = base + 0x1f;
+ port->altstatus_addr =
+ port->ctl_addr = base + 0x81a;
+}
+
+/**
+ * pdc2027x_init_one - PCI probe function
+ * Called when an instance of PCI adapter is inserted.
+ * This function checks whether the hardware is supported,
+ * initialize hardware and register an instance of ata_host to
+ * libata by providing struct ata_probe_ent and ata_device_add().
+ * (implements struct pci_driver.probe() )
+ *
+ * @pdev: instance of pci_dev found
+ * @ent: matching entry in the id_tbl[]
+ */
+static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ unsigned int board_idx = (unsigned int) ent->driver_data;
+
+ struct ata_probe_ent *probe_ent = NULL;
+ unsigned long base;
+ void __iomem *mmio_base;
+ int rc;
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+
+ rc = pci_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ rc = pci_request_regions(pdev, DRV_NAME);
+ if (rc)
+ goto err_out;
+
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ goto err_out_regions;
+
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ goto err_out_regions;
+
+ /* Prepare the probe entry */
+ probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
+ if (probe_ent == NULL) {
+ rc = -ENOMEM;
+ goto err_out_regions;
+ }
+
+ probe_ent->dev = pci_dev_to_dev(pdev);
+ INIT_LIST_HEAD(&probe_ent->node);
+
+ mmio_base = pci_iomap(pdev, 5, 0);
+ if (!mmio_base) {
+ rc = -ENOMEM;
+ goto err_out_free_ent;
+ }
+
+ base = (unsigned long) mmio_base;
+
+ probe_ent->sht = pdc2027x_port_info[board_idx].sht;
+ probe_ent->port_flags = pdc2027x_port_info[board_idx].flags;
+ probe_ent->pio_mask = pdc2027x_port_info[board_idx].pio_mask;
+ probe_ent->mwdma_mask = pdc2027x_port_info[board_idx].mwdma_mask;
+ probe_ent->udma_mask = pdc2027x_port_info[board_idx].udma_mask;
+ probe_ent->port_ops = pdc2027x_port_info[board_idx].port_ops;
+
+ probe_ent->irq = pdev->irq;
+ probe_ent->irq_flags = SA_SHIRQ;
+ probe_ent->mmio_base = mmio_base;
+
+ pdc_ata_setup_port(&probe_ent->port[0], base + 0x17c0);
+ probe_ent->port[0].bmdma_addr = base + 0x1000;
+ pdc_ata_setup_port(&probe_ent->port[1], base + 0x15c0);
+ probe_ent->port[1].bmdma_addr = base + 0x1008;
+
+ probe_ent->n_ports = 2;
+
+ pci_set_master(pdev);
+ //pci_enable_intx(pdev);
+
+ /* initialize adapter */
+ if (pdc_hardware_init(pdev, probe_ent, board_idx) != 0)
+ goto err_out_free_ent;
+
+ ata_device_add(probe_ent);
+ kfree(probe_ent);
+
+ return 0;
+
+err_out_free_ent:
+ kfree(probe_ent);
+err_out_regions:
+ pci_release_regions(pdev);
+err_out:
+ pci_disable_device(pdev);
+ return rc;
+}
+
+/**
+ * pdc2027x_remove_one - Called to remove a single instance of the
+ * adapter.
+ *
+ * @dev: The PCI device to remove.
+ * FIXME: module load/unload not working yet
+ */
+static void __devexit pdc2027x_remove_one(struct pci_dev *pdev)
+{
+ ata_pci_remove_one(pdev);
+}
+
+/**
+ * pdc2027x_init - Called after this module is loaded into the kernel.
+ */
+static int __init pdc2027x_init(void)
+{
+ return pci_register_driver(&pdc2027x_pci_driver);
+}
+
+/**
+ * pdc2027x_exit - Called before this module unloaded from the kernel
+ */
+static void __exit pdc2027x_exit(void)
+{
+ pci_unregister_driver(&pdc2027x_pci_driver);
+}
+
+module_init(pdc2027x_init);
+module_exit(pdc2027x_exit);
git://git.onelab.eu / linux-2.6.git / blobdiff