/*
* iop321 hardware bit definitions
*/
-#define IOP321_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */
-#define IOP321_ICR_UNIT_RESET 0x4000 /* 1=RESET */
-#define IOP321_ICR_SADIE 0x2000 /* 1=Slave Detect Interrupt Enable */
-#define IOP321_ICR_ALDIE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */
-#define IOP321_ICR_SSDIE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */
-#define IOP321_ICR_BERRIE 0x0400 /* 1=Bus Error Interrupt Enable */
-#define IOP321_ICR_RXFULLIE 0x0200 /* 1=Receive Full Interrupt Enable */
-#define IOP321_ICR_TXEMPTYIE 0x0100 /* 1=Transmit Empty Interrupt Enable */
-#define IOP321_ICR_GCD 0x0080 /* 1=General Call Disable */
+#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */
+#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */
+#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */
+#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */
+#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */
+#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */
+#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */
+#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */
+#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */
/*
- * IOP321_ICR_GCD: 1 disables response as slave. "This bit must be set
+ * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
* when sending a master mode general call message from the I2C unit"
*/
-#define IOP321_ICR_UE 0x0040 /* 1=Unit Enable */
+#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */
/*
* "NOTE: To avoid I2C bus integrity problems,
* the user needs to ensure that the GPIO Output Data Register -
* The user prepares to enable I2C port 0 and
* I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
*/
-#define IOP321_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */
-#define IOP321_ICR_MABORT 0x0010 /* 1=Send a STOP with no data
+#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */
+#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data
* NB TBYTE must be clear */
-#define IOP321_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */
-#define IOP321_ICR_NACK 0x0004 /* 1=reply with NACK */
-#define IOP321_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */
-#define IOP321_ICR_MSTART 0x0001 /* 1=initiate a START */
+#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */
+#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */
+#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */
+#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */
-#define IOP321_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */
-#define IOP321_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */
-#define IOP321_ISR_GCAD 0x0100 /* 1=General Call Address Detected */
-#define IOP321_ISR_RXFULL 0x0080 /* 1=Receive Full */
-#define IOP321_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */
-#define IOP321_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */
-#define IOP321_ISR_SSD 0x0010 /* 1=Slave STOP Detected */
-#define IOP321_ISR_BBUSY 0x0008 /* 1=Bus BUSY */
-#define IOP321_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */
-#define IOP321_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */
-#define IOP321_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */
+#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */
+#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */
+#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */
+#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */
+#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */
+#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */
+#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */
+#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */
+#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */
+#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */
+#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */
-#define IOP321_ISR_CLEARBITS 0x07f0
+#define IOP3XX_ISR_CLEARBITS 0x07f0
-#define IOP321_ISAR_SAMASK 0x007f
+#define IOP3XX_ISAR_SAMASK 0x007f
-#define IOP321_IDBR_MASK 0x00ff
+#define IOP3XX_IDBR_MASK 0x00ff
-#define IOP321_IBMR_SCL 0x0002
-#define IOP321_IBMR_SDA 0x0001
+#define IOP3XX_IBMR_SCL 0x0002
+#define IOP3XX_IBMR_SDA 0x0001
-#define IOP321_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
-#define IOP321_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
+#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
+#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
#define MYSAR 0x02 /* SWAG a suitable slave address */
#define I2C_ERR_ALD (I2C_ERR+1)
-struct iop3xx_biu { /* Bus Interface Unit - the hardware */
-/* physical hardware defs - regs*/
- u32 *CR;
- u32 *SR;
- u32 *SAR;
- u32 *DBR;
- u32 *BMR;
-/* irq bit vector */
- u32 irq;
-/* stored flags */
- u32 SR_enabled, SR_received;
-};
+#define CR_OFFSET 0
+#define SR_OFFSET 0x4
+#define SAR_OFFSET 0x8
+#define DBR_OFFSET 0xc
+#define CCR_OFFSET 0x10
+#define BMR_OFFSET 0x14
-struct i2c_algo_iop3xx_data {
- int channel;
+#define IOP3XX_I2C_IO_SIZE 0x18
+struct i2c_algo_iop3xx_data {
+ u32 ioaddr;
wait_queue_head_t waitq;
spinlock_t lock;
- int timeout;
- struct iop3xx_biu* biu;
+ u32 SR_enabled, SR_received;
+ int id;
};
-#define REGION_START(adap) ((u32)((adap)->biu->CR))
-#define REGION_END(adap) ((u32)((adap)->biu->BMR+1))
-#define REGION_LENGTH(adap) (REGION_END(adap)-REGION_START(adap))
-
-#define IRQ_STATUS_MASK(adap) (1<<adap->biu->irq)
-
#endif /* I2C_IOP3XX_H */
git://git.onelab.eu / linux-2.6.git / blobdiff