* *
* Copyright 2003 LSI Logic Corporation. All rights reserved. *
* *
- * Description *
- * ------------ *
- * This include file contains SAS firmware interface IOC Log Info codes *
+ * This file is confidential and a trade secret of LSI Logic. The *
+ * receipt of or possession of this file does not convey any rights to *
+ * reproduce or disclose its contents or to manufacture, use, or sell *
+ * anything it may describe, in whole, or in part, without the specific *
+ * written consent of LSI Logic Corporation. *
* *
- *-------------------------------------------------------------------------*
+ ***************************************************************************
+ *
+ * Name: iopiIocLogInfo.h
+ * Title: SAS Firmware IOP Interface IOC Log Info Definitions
+ * Programmer: Guy Kendall
+ * Creation Date: September 24, 2003
+ *
+ * Version History
+ * ---------------
+ *
+ * Last Updated
+ * -------------
+ * Version %version: 22 %
+ * Date Updated %date_modified: %
+ * Programmer %created_by: nperucca %
+ *
+ * Date Who Description
+ * -------- --- -------------------------------------------------------
+ * 09/24/03 GWK Initial version
+ *
+ *
+ * Description
+ * ------------
+ * This include file contains SAS firmware interface IOC Log Info codes
+ *
+ *-------------------------------------------------------------------------
*/
#ifndef IOPI_IOCLOGINFO_H_INCLUDED
#define IOPI_IOCLOGINFO_H_INCLUDED
-#define SAS_LOGINFO_NEXUS_LOSS 0x31170000
-#define SAS_LOGINFO_MASK 0xFFFF0000
/****************************************************************************/
/* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */
#define IOC_LOGINFO_ORIGINATOR_PL (0x01000000)
#define IOC_LOGINFO_ORIGINATOR_IR (0x02000000)
-#define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000)
-
/****************************************************************************/
/* LOGINFO_CODE defines */
/****************************************************************************/
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */
-
-#define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */
-
#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000)
-#define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */
-#define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */
-
-#define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001)
-#define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002)
-#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003)
-#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004)
-#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005)
/****************************************************************************/
/* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */
/****************************************************************************/
#define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000)
-#define PL_LOG_INFO_CODE_OPEN_FAILURE_NO_DEST_TIME_OUT (0x00010001)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_BAD_DESTINATION (0x00010011)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_PROTOCOL_NOT_SUPPORTED (0x00010013)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_STP_RESOURCES_BSY (0x00010018)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_WRONG_DESTINATION (0x00010019)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_ORR_TIMEOUT (0X0001001A)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_PATHWAY_BLOCKED (0x0001001B)
-#define PL_LOGINFO_CODE_OPEN_FAILURE_AWT_MAXED (0x0001001C)
#define PL_LOGINFO_CODE_INVALID_SGL (0x00020000)
#define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000)
#define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000)
#define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000)
#define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000)
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000)
-#define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */
#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */
#define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000)
-#define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below */
-#define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below */
+#define PL_LOGINFO_CODE_RESET (0x00110000)
+#define PL_LOGINFO_CODE_ABORT (0x00120000)
#define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000)
#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000)
-#define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000)
-#define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000)
-#define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000)
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100)
-#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101)
-#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */
-#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATHWAY_BLOCKED (0x0000011B)
-#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */
-
-#define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120)
-#define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */
-#define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */
-
-
#define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200)
#define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300)
#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400)
#define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00)
#define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00)
#define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00)
-#define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01)
-#define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00)
#define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000)
#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occured on SMP Read */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occured on SMP Write */
-#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */
-#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */
-#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */
-#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */
-#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */
-#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */
-#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */
+#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200001) /* Error occured on SMP Read */
+#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200002) /* Error occured on SMP Write */
+#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200004) /* Encl Mgmt services not available for this WWID */
+#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200005) /* Address Mode not suppored */
+#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200006) /* Invalid Slot Number in SEP Msg */
+#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200007) /* SGPIO not present/enabled */
#define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */
#define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */
#define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */
#define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */
-#define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */
-#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */
-#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transfering data */
-#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transfering sense data */
-#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */
-#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */
-#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */
-#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/
-#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode */
+#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200104) /* SEP stopped or sent bad chksum in Hdr */
+#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200105) /* SEP returned unknown scsi status */
+#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200106) /* SEP returned unknown scsi status */
+#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x00200107) /* SEP returned bad chksum after STOP */
+#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x00200108) /* SEP returned bad chksum after STOP while gettin data*/
/****************************************************************************/
/* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */
/****************************************************************************/
-#define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000)
-#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)
-
-/* Amount of information passed down for Create Volume is too large */
-#define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001)
-/* Creation of duplicate volume attempted (Bus/Target ID checked) */
-#define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002)
-/* Creation failed due to maximum number of supported volumes exceeded */
-#define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003)
-/* Creation failed due to DMA error in trying to read from host */
-#define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004)
-/* Creation failed due to invalid volume type passed down */
-#define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005)
-/* Creation failed due to error reading MFG Page 4 */
-#define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006)
-/* Creation failed when trying to create internal structures */
-#define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007)
-
-/* Activation failed due to trying to activate an already active volume */
-#define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010)
-/* Activation failed due to trying to active unsupported volume type */
-#define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011)
-/* Activation failed due to trying to active too many volumes */
-#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012)
-/* Activation failed due to Volume ID in use already */
-#define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013)
-/* Activation failed call to activateVolume returned failure */
-#define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014)
-/* Activation failed trying to import the volume */
-#define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015)
-
-/* Phys Disk failed, too many phys disks */
-#define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020)
-/* Amount of information passed down for Create Pnysdisk is too large */
-#define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021)
-/* Creation failed due to DMA error in trying to read from host */
-#define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022)
-/* Creation failed due to invalid Bus TargetID passed down */
-#define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023)
-/* Creation failed due to error in creating RAID Phys Disk Config Page */
-#define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024)
-
-
-/* Compatibility Error : IR Disabled */
-#define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030)
-/* Compatibility Error : Inquiry Comand failed */
-#define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031)
-/* Compatibility Error : Device not direct access device */
-#define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032)
-/* Compatibility Error : Removable device found */
-#define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033)
-/* Compatibility Error : Device SCSI Version not 2 or higher */
-#define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034)
-/* Compatibility Error : SATA device, 48 BIT LBA not supported */
-#define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035)
-/* Compatibility Error : Device does not have 512 byte block sizes */
-#define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036)
-/* Compatibility Error : Volume Type check failed */
-#define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037)
-/* Compatibility Error : Volume Type is unsupported by FW */
-#define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038)
-/* Compatibility Error : Disk drive too small for use in volume */
-#define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039)
-/* Compatibility Error : Phys disk for Create Volume not found */
-#define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A)
-/* Compatibility Error : membership count error, too many or too few disks for volume type */
-#define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B)
-/* Compatibility Error : Disk stripe sizes must be 64KB */
-#define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C)
-/* Compatibility Error : IME size limited to < 2TB */
-#define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D)
-
+#define IR_LOGINFO_CODE_UNUSED1 (0x00010000)
+#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)
/****************************************************************************/
-/* Defines for convenience */
+/* Defines for convienence */
/****************************************************************************/
#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP)
#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL)
git://git.onelab.eu / linux-2.6.git / blobdiff