linux 2.6.16.38 w/ vs2.0.3-rc1

[linux-2.6.git] / drivers / mtd / maps / Kconfig

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index 64d1b6a..7abd7fe 100644 (file)
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -13,13 +13,13 @@ config MTD_COMPLEX_MAPPINGS
 
 config MTD_PHYSMAP
        tristate "CFI Flash device in physical memory map"
-       depends on MTD_CFI || MTD_JEDECPROBE || MTD_ROM
+       depends on MTD_CFI
        help
-         This provides a 'mapping' driver which allows the NOR Flash and
-         ROM driver code to communicate with chips which are mapped
-         physically into the CPU's memory. You will need to configure
-         the physical address and size of the flash chips on your
-         particular board as well as the bus width, either statically
+         This provides a 'mapping' driver which allows the CFI probe and
+         command set driver code to communicate with flash chips which
+         are mapped physically into the CPU's memory. You will need to
+         configure the physical address and size of the flash chips on
+         your particular board as well as the bus width, either statically
          with config options or at run-time.
 
 config MTD_PHYSMAP_START
@@ -37,7 +37,7 @@ config MTD_PHYSMAP_START
 config MTD_PHYSMAP_LEN
        hex "Physical length of flash mapping"
        depends on MTD_PHYSMAP
-       default "0"
+       default "0x4000000"
        help
          This is the total length of the mapping of the flash chips on
          your particular board. If there is space, or aliases, in the
@@ -78,7 +78,7 @@ config MTD_PNC2000
 
 config MTD_SC520CDP
        tristate "CFI Flash device mapped on AMD SC520 CDP"
-       depends on X86 && MTD_CFI && MTD_CONCAT
+       depends on X86 && MTD_CFI
        help
          The SC520 CDP board has two banks of CFI-compliant chips and one
          Dual-in-line JEDEC chip. This 'mapping' driver supports that
@@ -109,7 +109,7 @@ config MTD_TS5500
          mtd1 allows you to reprogram your BIOS. BE VERY CAREFUL.
 
          Note that jumper 3 ("Write Enable Drive A") must be set
-         otherwise detection won't succeed.
+         otherwise detection won't succeeed.
 
 config MTD_SBC_GXX
        tristate "CFI Flash device mapped on Arcom SBC-GXx boards"
@@ -200,8 +200,8 @@ config MTD_TSUNAMI
          Support for the flash chip on Tsunami TIG bus.
 
 config MTD_LASAT
-       tristate "LASAT flash device"
-       depends on LASAT && MTD_CFI
+       tristate "Flash chips on LASAT board"
+       depends on LASAT
        help
          Support for the flash chips on the Lasat 100 and 200 boards.
 
@@ -212,7 +212,7 @@ config MTD_NETtel
          Support for flash chips on NETtel/SecureEdge/SnapGear boards.
 
 config MTD_ALCHEMY
-       tristate "AMD Alchemy Pb1xxx/Db1xxx/RDK MTD support"
+       tristate '  AMD Alchemy Pb1xxx/Db1xxx/RDK MTD support'
        depends on SOC_AU1X00
        help
          Flash memory access on AMD Alchemy Pb/Db/RDK Reference Boards
@@ -561,6 +561,7 @@ config MTD_PCMCIA
 config MTD_PCMCIA_ANONYMOUS
        bool "Use PCMCIA MTD drivers for anonymous PCMCIA cards"
        depends on MTD_PCMCIA
+       default N
        help
          If this option is enabled, PCMCIA cards which do not report
          anything about themselves are assumed to be MTD cards.