/**
* onenand_oob_64 - oob info for large (2KB) page
*/
-static struct nand_oobinfo onenand_oob_64 = {
- .useecc = MTD_NANDECC_AUTOPLACE,
+static struct nand_ecclayout onenand_oob_64 = {
.eccbytes = 20,
.eccpos = {
8, 9, 10, 11, 12,
},
.oobfree = {
{2, 3}, {14, 2}, {18, 3}, {30, 2},
- {24, 3}, {46, 2}, {40, 3}, {62, 2} }
+ {34, 3}, {46, 2}, {50, 3}, {62, 2}
+ }
};
/**
* onenand_oob_32 - oob info for middle (1KB) page
*/
-static struct nand_oobinfo onenand_oob_32 = {
- .useecc = MTD_NANDECC_AUTOPLACE,
+static struct nand_ecclayout onenand_oob_32 = {
.eccbytes = 10,
.eccpos = {
8, 9, 10, 11, 12,
static int onenand_command(struct mtd_info *mtd, int cmd, loff_t addr, size_t len)
{
struct onenand_chip *this = mtd->priv;
- int value, readcmd = 0;
+ int value, readcmd = 0, block_cmd = 0;
int block, page;
/* Now we use page size operation */
int sectors = 4, count = 4;
case ONENAND_CMD_ERASE:
case ONENAND_CMD_BUFFERRAM:
+ case ONENAND_CMD_OTP_ACCESS:
+ block_cmd = 1;
block = (int) (addr >> this->erase_shift);
page = -1;
break;
/* Write 'DFS, FBA' of Flash */
value = onenand_block_address(this, block);
this->write_word(value, this->base + ONENAND_REG_START_ADDRESS1);
+
+ if (block_cmd) {
+ /* Select DataRAM for DDP */
+ value = onenand_bufferram_address(this, block);
+ this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
+ }
}
if (page != -1) {
if (state != FL_READING)
cond_resched();
+ touch_softlockup_watchdog();
}
/* To get correct interrupt status in timeout case */
interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT);
if (ONENAND_CURRENT_BUFFERRAM(this)) {
if (area == ONENAND_DATARAM)
- return mtd->oobblock;
+ return mtd->writesize;
if (area == ONENAND_SPARERAM)
return mtd->oobsize;
}
bufferram += onenand_bufferram_offset(mtd, area);
+ if (ONENAND_CHECK_BYTE_ACCESS(count)) {
+ unsigned short word;
+
+ /* Align with word(16-bit) size */
+ count--;
+
+ /* Read word and save byte */
+ word = this->read_word(bufferram + offset + count);
+ buffer[count] = (word & 0xff);
+ }
+
memcpy(buffer, bufferram + offset, count);
return 0;
this->mmcontrol(mtd, ONENAND_SYS_CFG1_SYNC_READ);
+ if (ONENAND_CHECK_BYTE_ACCESS(count)) {
+ unsigned short word;
+
+ /* Align with word(16-bit) size */
+ count--;
+
+ /* Read word and save byte */
+ word = this->read_word(bufferram + offset + count);
+ buffer[count] = (word & 0xff);
+ }
+
memcpy(buffer, bufferram + offset, count);
this->mmcontrol(mtd, 0);
bufferram += onenand_bufferram_offset(mtd, area);
+ if (ONENAND_CHECK_BYTE_ACCESS(count)) {
+ unsigned short word;
+ int byte_offset;
+
+ /* Align with word(16-bit) size */
+ count--;
+
+ /* Calculate byte access offset */
+ byte_offset = offset + count;
+
+ /* Read word and save byte */
+ word = this->read_word(bufferram + byte_offset);
+ word = (word & ~0xff) | buffer[count];
+ this->write_word(word, bufferram + byte_offset);
+ }
+
memcpy(bufferram + offset, buffer, count);
return 0;
}
/**
- * onenand_read_ecc - [MTD Interface] Read data with ECC
+ * onenand_read - [MTD Interface] Read data from flash
* @param mtd MTD device structure
* @param from offset to read from
* @param len number of bytes to read
* @param retlen pointer to variable to store the number of read bytes
* @param buf the databuffer to put data
- * @param oob_buf filesystem supplied oob data buffer
- * @param oobsel oob selection structure
*
- * OneNAND read with ECC
- */
-static int onenand_read_ecc(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf,
- u_char *oob_buf, struct nand_oobinfo *oobsel)
+ * Read with ecc
+*/
+static int onenand_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
{
struct onenand_chip *this = mtd->priv;
int read = 0, column;
int thislen;
int ret = 0;
- DEBUG(MTD_DEBUG_LEVEL3, "onenand_read_ecc: from = 0x%08x, len = %i\n", (unsigned int) from, (int) len);
+ DEBUG(MTD_DEBUG_LEVEL3, "onenand_read: from = 0x%08x, len = %i\n", (unsigned int) from, (int) len);
/* Do not allow reads past end of device */
if ((from + len) > mtd->size) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_read_ecc: Attempt read beyond end of device\n");
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_read: Attempt read beyond end of device\n");
*retlen = 0;
return -EINVAL;
}
/* TODO handling oob */
while (read < len) {
- thislen = min_t(int, mtd->oobblock, len - read);
+ thislen = min_t(int, mtd->writesize, len - read);
- column = from & (mtd->oobblock - 1);
- if (column + thislen > mtd->oobblock)
- thislen = mtd->oobblock - column;
+ column = from & (mtd->writesize - 1);
+ if (column + thislen > mtd->writesize)
+ thislen = mtd->writesize - column;
if (!onenand_check_bufferram(mtd, from)) {
- this->command(mtd, ONENAND_CMD_READ, from, mtd->oobblock);
+ this->command(mtd, ONENAND_CMD_READ, from, mtd->writesize);
ret = this->wait(mtd, FL_READING);
/* First copy data and check return value for ECC handling */
break;
if (ret) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_read_ecc: read failed = %d\n", ret);
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_read: read failed = %d\n", ret);
goto out;
}
}
/**
- * onenand_read - [MTD Interface] MTD compability function for onenand_read_ecc
- * @param mtd MTD device structure
- * @param from offset to read from
- * @param len number of bytes to read
- * @param retlen pointer to variable to store the number of read bytes
- * @param buf the databuffer to put data
- *
- * This function simply calls onenand_read_ecc with oob buffer and oobsel = NULL
-*/
-static int onenand_read(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf)
-{
- return onenand_read_ecc(mtd, from, len, retlen, buf, NULL, NULL);
-}
-
-/**
- * onenand_read_oob - [MTD Interface] OneNAND read out-of-band
+ * onenand_do_read_oob - [MTD Interface] OneNAND read out-of-band
* @param mtd MTD device structure
* @param from offset to read from
* @param len number of bytes to read
*
* OneNAND read out-of-band data from the spare area
*/
-static int onenand_read_oob(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf)
+int onenand_do_read_oob(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
{
struct onenand_chip *this = mtd->priv;
int read = 0, thislen, column;
/* Read more? */
if (read < len) {
/* Page size */
- from += mtd->oobblock;
+ from += mtd->writesize;
column = 0;
}
}
return ret;
}
+/**
+ * onenand_read_oob - [MTD Interface] NAND write data and/or out-of-band
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operation description structure
+ */
+static int onenand_read_oob(struct mtd_info *mtd, loff_t from,
+ struct mtd_oob_ops *ops)
+{
+ BUG_ON(ops->mode != MTD_OOB_PLACE);
+
+ return onenand_do_read_oob(mtd, from + ops->ooboffs, ops->len,
+ &ops->retlen, ops->oobbuf);
+}
+
#ifdef CONFIG_MTD_ONENAND_VERIFY_WRITE
+/**
+ * onenand_verify_oob - [GENERIC] verify the oob contents after a write
+ * @param mtd MTD device structure
+ * @param buf the databuffer to verify
+ * @param to offset to read from
+ * @param len number of bytes to read and compare
+ *
+ */
+static int onenand_verify_oob(struct mtd_info *mtd, const u_char *buf, loff_t to, int len)
+{
+ struct onenand_chip *this = mtd->priv;
+ char *readp = this->page_buf;
+ int column = to & (mtd->oobsize - 1);
+ int status, i;
+
+ this->command(mtd, ONENAND_CMD_READOOB, to, mtd->oobsize);
+ onenand_update_bufferram(mtd, to, 0);
+ status = this->wait(mtd, FL_READING);
+ if (status)
+ return status;
+
+ this->read_bufferram(mtd, ONENAND_SPARERAM, readp, column, len);
+
+ for(i = 0; i < len; i++)
+ if (buf[i] != 0xFF && buf[i] != readp[i])
+ return -EBADMSG;
+
+ return 0;
+}
+
/**
* onenand_verify_page - [GENERIC] verify the chip contents after a write
* @param mtd MTD device structure
void __iomem *dataram0, *dataram1;
int ret = 0;
- this->command(mtd, ONENAND_CMD_READ, addr, mtd->oobblock);
+ this->command(mtd, ONENAND_CMD_READ, addr, mtd->writesize);
ret = this->wait(mtd, FL_READING);
if (ret)
/* Check, if the two dataram areas are same */
dataram0 = this->base + ONENAND_DATARAM;
- dataram1 = dataram0 + mtd->oobblock;
+ dataram1 = dataram0 + mtd->writesize;
- if (memcmp(dataram0, dataram1, mtd->oobblock))
+ if (memcmp(dataram0, dataram1, mtd->writesize))
return -EBADMSG;
return 0;
}
#else
#define onenand_verify_page(...) (0)
+#define onenand_verify_oob(...) (0)
#endif
-#define NOTALIGNED(x) ((x & (mtd->oobblock - 1)) != 0)
+#define NOTALIGNED(x) ((x & (mtd->writesize - 1)) != 0)
/**
- * onenand_write_ecc - [MTD Interface] OneNAND write with ECC
+ * onenand_write - [MTD Interface] write buffer to FLASH
* @param mtd MTD device structure
* @param to offset to write to
* @param len number of bytes to write
* @param retlen pointer to variable to store the number of written bytes
* @param buf the data to write
- * @param eccbuf filesystem supplied oob data buffer
- * @param oobsel oob selection structure
*
- * OneNAND write with ECC
+ * Write with ECC
*/
-static int onenand_write_ecc(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf,
- u_char *eccbuf, struct nand_oobinfo *oobsel)
+static int onenand_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
{
struct onenand_chip *this = mtd->priv;
int written = 0;
int ret = 0;
- DEBUG(MTD_DEBUG_LEVEL3, "onenand_write_ecc: to = 0x%08x, len = %i\n", (unsigned int) to, (int) len);
+ DEBUG(MTD_DEBUG_LEVEL3, "onenand_write: to = 0x%08x, len = %i\n", (unsigned int) to, (int) len);
/* Initialize retlen, in case of early exit */
*retlen = 0;
/* Do not allow writes past end of device */
if (unlikely((to + len) > mtd->size)) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_write_ecc: Attempt write to past end of device\n");
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_write: Attempt write to past end of device\n");
return -EINVAL;
}
/* Reject writes, which are not page aligned */
if (unlikely(NOTALIGNED(to)) || unlikely(NOTALIGNED(len))) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_write_ecc: Attempt to write not page aligned data\n");
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_write: Attempt to write not page aligned data\n");
return -EINVAL;
}
/* Loop until all data write */
while (written < len) {
- int thislen = min_t(int, mtd->oobblock, len - written);
+ int thislen = min_t(int, mtd->writesize, len - written);
- this->command(mtd, ONENAND_CMD_BUFFERRAM, to, mtd->oobblock);
+ this->command(mtd, ONENAND_CMD_BUFFERRAM, to, mtd->writesize);
this->write_bufferram(mtd, ONENAND_DATARAM, buf, 0, thislen);
this->write_bufferram(mtd, ONENAND_SPARERAM, ffchars, 0, mtd->oobsize);
- this->command(mtd, ONENAND_CMD_PROG, to, mtd->oobblock);
+ this->command(mtd, ONENAND_CMD_PROG, to, mtd->writesize);
onenand_update_bufferram(mtd, to, 1);
ret = this->wait(mtd, FL_WRITING);
if (ret) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_write_ecc: write filaed %d\n", ret);
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_write: write filaed %d\n", ret);
goto out;
}
/* Only check verify write turn on */
ret = onenand_verify_page(mtd, (u_char *) buf, to);
if (ret) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_write_ecc: verify failed %d\n", ret);
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_write: verify failed %d\n", ret);
goto out;
}
}
/**
- * onenand_write - [MTD Interface] compability function for onenand_write_ecc
- * @param mtd MTD device structure
- * @param to offset to write to
- * @param len number of bytes to write
- * @param retlen pointer to variable to store the number of written bytes
- * @param buf the data to write
- *
- * This function simply calls onenand_write_ecc
- * with oob buffer and oobsel = NULL
- */
-static int onenand_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
-{
- return onenand_write_ecc(mtd, to, len, retlen, buf, NULL, NULL);
-}
-
-/**
- * onenand_write_oob - [MTD Interface] OneNAND write out-of-band
+ * onenand_do_write_oob - [Internal] OneNAND write out-of-band
* @param mtd MTD device structure
* @param to offset to write to
* @param len number of bytes to write
*
* OneNAND write out-of-band
*/
-static int onenand_write_oob(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
+static int onenand_do_write_oob(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
{
struct onenand_chip *this = mtd->priv;
- int column, status;
+ int column, ret = 0;
int written = 0;
DEBUG(MTD_DEBUG_LEVEL3, "onenand_write_oob: to = 0x%08x, len = %i\n", (unsigned int) to, (int) len);
this->command(mtd, ONENAND_CMD_BUFFERRAM, to, mtd->oobsize);
- this->write_bufferram(mtd, ONENAND_SPARERAM, ffchars, 0, mtd->oobsize);
- this->write_bufferram(mtd, ONENAND_SPARERAM, buf, column, thislen);
+ /* We send data to spare ram with oobsize
+ * to prevent byte access */
+ memset(this->page_buf, 0xff, mtd->oobsize);
+ memcpy(this->page_buf + column, buf, thislen);
+ this->write_bufferram(mtd, ONENAND_SPARERAM, this->page_buf, 0, mtd->oobsize);
this->command(mtd, ONENAND_CMD_PROGOOB, to, mtd->oobsize);
onenand_update_bufferram(mtd, to, 0);
- status = this->wait(mtd, FL_WRITING);
- if (status)
+ ret = this->wait(mtd, FL_WRITING);
+ if (ret) {
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_write_oob: write filaed %d\n", ret);
+ goto out;
+ }
+
+ ret = onenand_verify_oob(mtd, buf, to, thislen);
+ if (ret) {
+ DEBUG(MTD_DEBUG_LEVEL0, "onenand_write_oob: verify failed %d\n", ret);
goto out;
+ }
written += thislen;
*retlen = written;
- return 0;
+ return ret;
}
/**
- * onenand_writev_ecc - [MTD Interface] write with iovec with ecc
- * @param mtd MTD device structure
- * @param vecs the iovectors to write
- * @param count number of vectors
- * @param to offset to write to
- * @param retlen pointer to variable to store the number of written bytes
- * @param eccbuf filesystem supplied oob data buffer
- * @param oobsel oob selection structure
- *
- * OneNAND write with iovec with ecc
+ * onenand_write_oob - [MTD Interface] NAND write data and/or out-of-band
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operation description structure
*/
-static int onenand_writev_ecc(struct mtd_info *mtd, const struct kvec *vecs,
- unsigned long count, loff_t to, size_t *retlen,
- u_char *eccbuf, struct nand_oobinfo *oobsel)
+static int onenand_write_oob(struct mtd_info *mtd, loff_t to,
+ struct mtd_oob_ops *ops)
{
- struct onenand_chip *this = mtd->priv;
- unsigned char *pbuf;
- size_t total_len, len;
- int i, written = 0;
- int ret = 0;
-
- /* Preset written len for early exit */
- *retlen = 0;
-
- /* Calculate total length of data */
- total_len = 0;
- for (i = 0; i < count; i++)
- total_len += vecs[i].iov_len;
-
- DEBUG(MTD_DEBUG_LEVEL3, "onenand_writev_ecc: to = 0x%08x, len = %i, count = %ld\n", (unsigned int) to, (unsigned int) total_len, count);
-
- /* Do not allow write past end of the device */
- if (unlikely((to + total_len) > mtd->size)) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_writev_ecc: Attempted write past end of device\n");
- return -EINVAL;
- }
-
- /* Reject writes, which are not page aligned */
- if (unlikely(NOTALIGNED(to)) || unlikely(NOTALIGNED(total_len))) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_writev_ecc: Attempt to write not page aligned data\n");
- return -EINVAL;
- }
-
- /* Grab the lock and see if the device is available */
- onenand_get_device(mtd, FL_WRITING);
-
- /* TODO handling oob */
-
- /* Loop until all keve's data has been written */
- len = 0;
- while (count) {
- pbuf = this->page_buf;
- /*
- * If the given tuple is >= pagesize then
- * write it out from the iov
- */
- if ((vecs->iov_len - len) >= mtd->oobblock) {
- pbuf = vecs->iov_base + len;
-
- len += mtd->oobblock;
-
- /* Check, if we have to switch to the next tuple */
- if (len >= (int) vecs->iov_len) {
- vecs++;
- len = 0;
- count--;
- }
- } else {
- int cnt = 0, thislen;
- while (cnt < mtd->oobblock) {
- thislen = min_t(int, mtd->oobblock - cnt, vecs->iov_len - len);
- memcpy(this->page_buf + cnt, vecs->iov_base + len, thislen);
- cnt += thislen;
- len += thislen;
-
- /* Check, if we have to switch to the next tuple */
- if (len >= (int) vecs->iov_len) {
- vecs++;
- len = 0;
- count--;
- }
- }
- }
-
- this->command(mtd, ONENAND_CMD_BUFFERRAM, to, mtd->oobblock);
+ BUG_ON(ops->mode != MTD_OOB_PLACE);
- this->write_bufferram(mtd, ONENAND_DATARAM, pbuf, 0, mtd->oobblock);
- this->write_bufferram(mtd, ONENAND_SPARERAM, ffchars, 0, mtd->oobsize);
-
- this->command(mtd, ONENAND_CMD_PROG, to, mtd->oobblock);
-
- onenand_update_bufferram(mtd, to, 1);
-
- ret = this->wait(mtd, FL_WRITING);
- if (ret) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_writev_ecc: write failed %d\n", ret);
- goto out;
- }
-
-
- /* Only check verify write turn on */
- ret = onenand_verify_page(mtd, (u_char *) pbuf, to);
- if (ret) {
- DEBUG(MTD_DEBUG_LEVEL0, "onenand_writev_ecc: verify failed %d\n", ret);
- goto out;
- }
-
- written += mtd->oobblock;
-
- to += mtd->oobblock;
- }
-
-out:
- /* Deselect and wakt up anyone waiting on the device */
- onenand_release_device(mtd);
-
- *retlen = written;
-
- return 0;
-}
-
-/**
- * onenand_writev - [MTD Interface] compabilty function for onenand_writev_ecc
- * @param mtd MTD device structure
- * @param vecs the iovectors to write
- * @param count number of vectors
- * @param to offset to write to
- * @param retlen pointer to variable to store the number of written bytes
- *
- * OneNAND write with kvec. This just calls the ecc function
- */
-static int onenand_writev(struct mtd_info *mtd, const struct kvec *vecs,
- unsigned long count, loff_t to, size_t *retlen)
-{
- return onenand_writev_ecc(mtd, vecs, count, to, retlen, NULL, NULL);
+ return onenand_do_write_oob(mtd, to + ops->ooboffs, ops->len,
+ &ops->retlen, ops->oobbuf);
}
/**
/* We write two bytes, so we dont have to mess with 16 bit access */
ofs += mtd->oobsize + (bbm->badblockpos & ~0x01);
- return mtd->write_oob(mtd, ofs , 2, &retlen, buf);
+ return onenand_do_write_oob(mtd, ofs , 2, &retlen, buf);
}
/**
return 0;
}
+#ifdef CONFIG_MTD_ONENAND_OTP
+
+/* Interal OTP operation */
+typedef int (*otp_op_t)(struct mtd_info *mtd, loff_t form, size_t len,
+ size_t *retlen, u_char *buf);
+
+/**
+ * do_otp_read - [DEFAULT] Read OTP block area
+ * @param mtd MTD device structure
+ * @param from The offset to read
+ * @param len number of bytes to read
+ * @param retlen pointer to variable to store the number of readbytes
+ * @param buf the databuffer to put/get data
+ *
+ * Read OTP block area.
+ */
+static int do_otp_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct onenand_chip *this = mtd->priv;
+ int ret;
+
+ /* Enter OTP access mode */
+ this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+ this->wait(mtd, FL_OTPING);
+
+ ret = mtd->read(mtd, from, len, retlen, buf);
+
+ /* Exit OTP access mode */
+ this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+ this->wait(mtd, FL_RESETING);
+
+ return ret;
+}
+
+/**
+ * do_otp_write - [DEFAULT] Write OTP block area
+ * @param mtd MTD device structure
+ * @param from The offset to write
+ * @param len number of bytes to write
+ * @param retlen pointer to variable to store the number of write bytes
+ * @param buf the databuffer to put/get data
+ *
+ * Write OTP block area.
+ */
+static int do_otp_write(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct onenand_chip *this = mtd->priv;
+ unsigned char *pbuf = buf;
+ int ret;
+
+ /* Force buffer page aligned */
+ if (len < mtd->writesize) {
+ memcpy(this->page_buf, buf, len);
+ memset(this->page_buf + len, 0xff, mtd->writesize - len);
+ pbuf = this->page_buf;
+ len = mtd->writesize;
+ }
+
+ /* Enter OTP access mode */
+ this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+ this->wait(mtd, FL_OTPING);
+
+ ret = mtd->write(mtd, from, len, retlen, pbuf);
+
+ /* Exit OTP access mode */
+ this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+ this->wait(mtd, FL_RESETING);
+
+ return ret;
+}
+
+/**
+ * do_otp_lock - [DEFAULT] Lock OTP block area
+ * @param mtd MTD device structure
+ * @param from The offset to lock
+ * @param len number of bytes to lock
+ * @param retlen pointer to variable to store the number of lock bytes
+ * @param buf the databuffer to put/get data
+ *
+ * Lock OTP block area.
+ */
+static int do_otp_lock(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct onenand_chip *this = mtd->priv;
+ int ret;
+
+ /* Enter OTP access mode */
+ this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+ this->wait(mtd, FL_OTPING);
+
+ ret = onenand_do_write_oob(mtd, from, len, retlen, buf);
+
+ /* Exit OTP access mode */
+ this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+ this->wait(mtd, FL_RESETING);
+
+ return ret;
+}
+
+/**
+ * onenand_otp_walk - [DEFAULT] Handle OTP operation
+ * @param mtd MTD device structure
+ * @param from The offset to read/write
+ * @param len number of bytes to read/write
+ * @param retlen pointer to variable to store the number of read bytes
+ * @param buf the databuffer to put/get data
+ * @param action do given action
+ * @param mode specify user and factory
+ *
+ * Handle OTP operation.
+ */
+static int onenand_otp_walk(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf,
+ otp_op_t action, int mode)
+{
+ struct onenand_chip *this = mtd->priv;
+ int otp_pages;
+ int density;
+ int ret = 0;
+
+ *retlen = 0;
+
+ density = this->device_id >> ONENAND_DEVICE_DENSITY_SHIFT;
+ if (density < ONENAND_DEVICE_DENSITY_512Mb)
+ otp_pages = 20;
+ else
+ otp_pages = 10;
+
+ if (mode == MTD_OTP_FACTORY) {
+ from += mtd->writesize * otp_pages;
+ otp_pages = 64 - otp_pages;
+ }
+
+ /* Check User/Factory boundary */
+ if (((mtd->writesize * otp_pages) - (from + len)) < 0)
+ return 0;
+
+ while (len > 0 && otp_pages > 0) {
+ if (!action) { /* OTP Info functions */
+ struct otp_info *otpinfo;
+
+ len -= sizeof(struct otp_info);
+ if (len <= 0)
+ return -ENOSPC;
+
+ otpinfo = (struct otp_info *) buf;
+ otpinfo->start = from;
+ otpinfo->length = mtd->writesize;
+ otpinfo->locked = 0;
+
+ from += mtd->writesize;
+ buf += sizeof(struct otp_info);
+ *retlen += sizeof(struct otp_info);
+ } else {
+ size_t tmp_retlen;
+ int size = len;
+
+ ret = action(mtd, from, len, &tmp_retlen, buf);
+
+ buf += size;
+ len -= size;
+ *retlen += size;
+
+ if (ret < 0)
+ return ret;
+ }
+ otp_pages--;
+ }
+
+ return 0;
+}
+
+/**
+ * onenand_get_fact_prot_info - [MTD Interface] Read factory OTP info
+ * @param mtd MTD device structure
+ * @param buf the databuffer to put/get data
+ * @param len number of bytes to read
+ *
+ * Read factory OTP info.
+ */
+static int onenand_get_fact_prot_info(struct mtd_info *mtd,
+ struct otp_info *buf, size_t len)
+{
+ size_t retlen;
+ int ret;
+
+ ret = onenand_otp_walk(mtd, 0, len, &retlen, (u_char *) buf, NULL, MTD_OTP_FACTORY);
+
+ return ret ? : retlen;
+}
+
+/**
+ * onenand_read_fact_prot_reg - [MTD Interface] Read factory OTP area
+ * @param mtd MTD device structure
+ * @param from The offset to read
+ * @param len number of bytes to read
+ * @param retlen pointer to variable to store the number of read bytes
+ * @param buf the databuffer to put/get data
+ *
+ * Read factory OTP area.
+ */
+static int onenand_read_fact_prot_reg(struct mtd_info *mtd, loff_t from,
+ size_t len, size_t *retlen, u_char *buf)
+{
+ return onenand_otp_walk(mtd, from, len, retlen, buf, do_otp_read, MTD_OTP_FACTORY);
+}
+
+/**
+ * onenand_get_user_prot_info - [MTD Interface] Read user OTP info
+ * @param mtd MTD device structure
+ * @param buf the databuffer to put/get data
+ * @param len number of bytes to read
+ *
+ * Read user OTP info.
+ */
+static int onenand_get_user_prot_info(struct mtd_info *mtd,
+ struct otp_info *buf, size_t len)
+{
+ size_t retlen;
+ int ret;
+
+ ret = onenand_otp_walk(mtd, 0, len, &retlen, (u_char *) buf, NULL, MTD_OTP_USER);
+
+ return ret ? : retlen;
+}
+
+/**
+ * onenand_read_user_prot_reg - [MTD Interface] Read user OTP area
+ * @param mtd MTD device structure
+ * @param from The offset to read
+ * @param len number of bytes to read
+ * @param retlen pointer to variable to store the number of read bytes
+ * @param buf the databuffer to put/get data
+ *
+ * Read user OTP area.
+ */
+static int onenand_read_user_prot_reg(struct mtd_info *mtd, loff_t from,
+ size_t len, size_t *retlen, u_char *buf)
+{
+ return onenand_otp_walk(mtd, from, len, retlen, buf, do_otp_read, MTD_OTP_USER);
+}
+
+/**
+ * onenand_write_user_prot_reg - [MTD Interface] Write user OTP area
+ * @param mtd MTD device structure
+ * @param from The offset to write
+ * @param len number of bytes to write
+ * @param retlen pointer to variable to store the number of write bytes
+ * @param buf the databuffer to put/get data
+ *
+ * Write user OTP area.
+ */
+static int onenand_write_user_prot_reg(struct mtd_info *mtd, loff_t from,
+ size_t len, size_t *retlen, u_char *buf)
+{
+ return onenand_otp_walk(mtd, from, len, retlen, buf, do_otp_write, MTD_OTP_USER);
+}
+
+/**
+ * onenand_lock_user_prot_reg - [MTD Interface] Lock user OTP area
+ * @param mtd MTD device structure
+ * @param from The offset to lock
+ * @param len number of bytes to unlock
+ *
+ * Write lock mark on spare area in page 0 in OTP block
+ */
+static int onenand_lock_user_prot_reg(struct mtd_info *mtd, loff_t from,
+ size_t len)
+{
+ unsigned char oob_buf[64];
+ size_t retlen;
+ int ret;
+
+ memset(oob_buf, 0xff, mtd->oobsize);
+ /*
+ * Note: OTP lock operation
+ * OTP block : 0xXXFC
+ * 1st block : 0xXXF3 (If chip support)
+ * Both : 0xXXF0 (If chip support)
+ */
+ oob_buf[ONENAND_OTP_LOCK_OFFSET] = 0xFC;
+
+ /*
+ * Write lock mark to 8th word of sector0 of page0 of the spare0.
+ * We write 16 bytes spare area instead of 2 bytes.
+ */
+ from = 0;
+ len = 16;
+
+ ret = onenand_otp_walk(mtd, from, len, &retlen, oob_buf, do_otp_lock, MTD_OTP_USER);
+
+ return ret ? : retlen;
+}
+#endif /* CONFIG_MTD_ONENAND_OTP */
+
/**
* onenand_print_device_info - Print device ID
* @param device device ID
/* OneNAND page size & block size */
/* The data buffer size is equal to page size */
- mtd->oobblock = this->read_word(this->base + ONENAND_REG_DATA_BUFFER_SIZE);
- mtd->oobsize = mtd->oobblock >> 5;
+ mtd->writesize = this->read_word(this->base + ONENAND_REG_DATA_BUFFER_SIZE);
+ mtd->oobsize = mtd->writesize >> 5;
/* Pagers per block is always 64 in OneNAND */
- mtd->erasesize = mtd->oobblock << 6;
+ mtd->erasesize = mtd->writesize << 6;
this->erase_shift = ffs(mtd->erasesize) - 1;
- this->page_shift = ffs(mtd->oobblock) - 1;
+ this->page_shift = ffs(mtd->writesize) - 1;
this->ppb_shift = (this->erase_shift - this->page_shift);
- this->page_mask = (mtd->erasesize / mtd->oobblock) - 1;
+ this->page_mask = (mtd->erasesize / mtd->writesize) - 1;
/* REVIST: Multichip handling */
"in suspended state\n");
}
-
/**
* onenand_scan - [OneNAND Interface] Scan for the OneNAND device
* @param mtd MTD device structure
/* Allocate buffers, if necessary */
if (!this->page_buf) {
size_t len;
- len = mtd->oobblock + mtd->oobsize;
+ len = mtd->writesize + mtd->oobsize;
this->page_buf = kmalloc(len, GFP_KERNEL);
if (!this->page_buf) {
printk(KERN_ERR "onenand_scan(): Can't allocate page_buf\n");
switch (mtd->oobsize) {
case 64:
- this->autooob = &onenand_oob_64;
+ this->ecclayout = &onenand_oob_64;
break;
case 32:
- this->autooob = &onenand_oob_32;
+ this->ecclayout = &onenand_oob_32;
break;
default:
printk(KERN_WARNING "No OOB scheme defined for oobsize %d\n",
mtd->oobsize);
/* To prevent kernel oops */
- this->autooob = &onenand_oob_32;
+ this->ecclayout = &onenand_oob_32;
break;
}
- memcpy(&mtd->oobinfo, this->autooob, sizeof(mtd->oobinfo));
+ mtd->ecclayout = this->ecclayout;
/* Fill in remaining MTD driver data */
mtd->type = MTD_NANDFLASH;
- mtd->flags = MTD_CAP_NANDFLASH | MTD_ECC;
+ mtd->flags = MTD_CAP_NANDFLASH;
mtd->ecctype = MTD_ECC_SW;
mtd->erase = onenand_erase;
mtd->point = NULL;
mtd->unpoint = NULL;
mtd->read = onenand_read;
mtd->write = onenand_write;
- mtd->read_ecc = onenand_read_ecc;
- mtd->write_ecc = onenand_write_ecc;
mtd->read_oob = onenand_read_oob;
mtd->write_oob = onenand_write_oob;
- mtd->readv = NULL;
- mtd->readv_ecc = NULL;
- mtd->writev = onenand_writev;
- mtd->writev_ecc = onenand_writev_ecc;
+#ifdef CONFIG_MTD_ONENAND_OTP
+ mtd->get_fact_prot_info = onenand_get_fact_prot_info;
+ mtd->read_fact_prot_reg = onenand_read_fact_prot_reg;
+ mtd->get_user_prot_info = onenand_get_user_prot_info;
+ mtd->read_user_prot_reg = onenand_read_user_prot_reg;
+ mtd->write_user_prot_reg = onenand_write_user_prot_reg;
+ mtd->lock_user_prot_reg = onenand_lock_user_prot_reg;
+#endif
mtd->sync = onenand_sync;
mtd->lock = NULL;
mtd->unlock = onenand_unlock;
git://git.onelab.eu / linux-2.6.git / blobdiff