/* bnx2.h: Broadcom NX2 network driver.
*
- * Copyright (c) 2004, 2005 Broadcom Corporation
+ * Copyright (c) 2004, 2005, 2006 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#ifndef BNX2_H
#define BNX2_H
-#include <linux/config.h>
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/dma-mapping.h>
-#include <asm/bitops.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <linux/delay.h>
-#include <asm/byteorder.h>
-#include <linux/time.h>
-#include <linux/ethtool.h>
-#include <linux/mii.h>
-#ifdef NETIF_F_HW_VLAN_TX
-#include <linux/if_vlan.h>
-#define BCM_VLAN 1
-#endif
-#ifdef NETIF_F_TSO
-#include <net/ip.h>
-#include <net/tcp.h>
-#include <net/checksum.h>
-#define BCM_TSO 1
-#endif
-#include <linux/workqueue.h>
-#include <linux/crc32.h>
-
/* Hardware data structures and register definitions automatically
* generated from RTL code. Do not modify.
*/
* l2_fhdr definition
*/
struct l2_fhdr {
-#if defined(__BIG_ENDIAN)
- u16 l2_fhdr_errors;
- u16 l2_fhdr_status;
-#elif defined(__LITTLE_ENDIAN)
- u16 l2_fhdr_status;
- u16 l2_fhdr_errors;
-#endif
- #define L2_FHDR_ERRORS_BAD_CRC (1<<1)
- #define L2_FHDR_ERRORS_PHY_DECODE (1<<2)
- #define L2_FHDR_ERRORS_ALIGNMENT (1<<3)
- #define L2_FHDR_ERRORS_TOO_SHORT (1<<4)
- #define L2_FHDR_ERRORS_GIANT_FRAME (1<<5)
-
+ u32 l2_fhdr_status;
#define L2_FHDR_STATUS_RULE_CLASS (0x7<<0)
#define L2_FHDR_STATUS_RULE_P2 (1<<3)
#define L2_FHDR_STATUS_RULE_P3 (1<<4)
#define L2_FHDR_STATUS_TCP_SEGMENT (1<<14)
#define L2_FHDR_STATUS_UDP_DATAGRAM (1<<15)
+ #define L2_FHDR_ERRORS_BAD_CRC (1<<17)
+ #define L2_FHDR_ERRORS_PHY_DECODE (1<<18)
+ #define L2_FHDR_ERRORS_ALIGNMENT (1<<19)
+ #define L2_FHDR_ERRORS_TOO_SHORT (1<<20)
+ #define L2_FHDR_ERRORS_GIANT_FRAME (1<<21)
+ #define L2_FHDR_ERRORS_TCP_XSUM (1<<28)
+ #define L2_FHDR_ERRORS_UDP_XSUM (1<<31)
+
u32 l2_fhdr_hash;
#if defined(__BIG_ENDIAN)
u16 l2_fhdr_pkt_len;
#define BNX2_EMAC_MODE_PORT_NONE (0L<<2)
#define BNX2_EMAC_MODE_PORT_MII (1L<<2)
#define BNX2_EMAC_MODE_PORT_GMII (2L<<2)
-#define BNX2_EMAC_MODE_PORT_UNDEF (3L<<2)
+#define BNX2_EMAC_MODE_PORT_MII_10 (3L<<2)
#define BNX2_EMAC_MODE_MAC_LOOP (1L<<4)
+#define BNX2_EMAC_MODE_25G (1L<<5)
#define BNX2_EMAC_MODE_TAGGED_MAC_CTL (1L<<7)
#define BNX2_EMAC_MODE_TX_BURST (1L<<8)
#define BNX2_EMAC_MODE_MAX_DEFER_DROP_ENA (1L<<9)
#define BNX2_MCP_ROM 0x00150000
#define BNX2_MCP_SCRATCH 0x00160000
+#define BNX2_SHM_HDR_SIGNATURE BNX2_MCP_SCRATCH
+#define BNX2_SHM_HDR_SIGNATURE_SIG_MASK 0xffff0000
+#define BNX2_SHM_HDR_SIGNATURE_SIG 0x53530000
+#define BNX2_SHM_HDR_SIGNATURE_VER_MASK 0x000000ff
+#define BNX2_SHM_HDR_SIGNATURE_VER_ONE 0x00000001
+
+#define BNX2_SHM_HDR_ADDR_0 BNX2_MCP_SCRATCH + 4
+#define BNX2_SHM_HDR_ADDR_1 BNX2_MCP_SCRATCH + 8
+
#define NUM_MC_HASH_REGISTERS 8
#define PHY_ID(id) ((id) & 0xfffffff0)
#define PHY_REV_ID(id) ((id) & 0xf)
+/* 5708 Serdes PHY registers */
+
+#define BCM5708S_UP1 0xb
+
+#define BCM5708S_UP1_2G5 0x1
+
+#define BCM5708S_BLK_ADDR 0x1f
+
+#define BCM5708S_BLK_ADDR_DIG 0x0000
+#define BCM5708S_BLK_ADDR_DIG3 0x0002
+#define BCM5708S_BLK_ADDR_TX_MISC 0x0005
+
+/* Digital Block */
+#define BCM5708S_1000X_CTL1 0x10
+
+#define BCM5708S_1000X_CTL1_FIBER_MODE 0x0001
+#define BCM5708S_1000X_CTL1_AUTODET_EN 0x0010
+
+#define BCM5708S_1000X_CTL2 0x11
+
+#define BCM5708S_1000X_CTL2_PLLEL_DET_EN 0x0001
+
+#define BCM5708S_1000X_STAT1 0x14
+
+#define BCM5708S_1000X_STAT1_SGMII 0x0001
+#define BCM5708S_1000X_STAT1_LINK 0x0002
+#define BCM5708S_1000X_STAT1_FD 0x0004
+#define BCM5708S_1000X_STAT1_SPEED_MASK 0x0018
+#define BCM5708S_1000X_STAT1_SPEED_10 0x0000
+#define BCM5708S_1000X_STAT1_SPEED_100 0x0008
+#define BCM5708S_1000X_STAT1_SPEED_1G 0x0010
+#define BCM5708S_1000X_STAT1_SPEED_2G5 0x0018
+#define BCM5708S_1000X_STAT1_TX_PAUSE 0x0020
+#define BCM5708S_1000X_STAT1_RX_PAUSE 0x0040
+
+/* Digital3 Block */
+#define BCM5708S_DIG_3_0 0x10
+
+#define BCM5708S_DIG_3_0_USE_IEEE 0x0001
+
+/* Tx/Misc Block */
+#define BCM5708S_TX_ACTL1 0x15
+
+#define BCM5708S_TX_ACTL1_DRIVER_VCM 0x30
+
+#define BCM5708S_TX_ACTL3 0x17
+
#define MIN_ETHERNET_PACKET_SIZE 60
#define MAX_ETHERNET_PACKET_SIZE 1514
#define MAX_ETHERNET_JUMBO_PACKET_SIZE 9014
#define TX_DESC_CNT (BCM_PAGE_SIZE / sizeof(struct tx_bd))
#define MAX_TX_DESC_CNT (TX_DESC_CNT - 1)
+#define MAX_RX_RINGS 4
#define RX_DESC_CNT (BCM_PAGE_SIZE / sizeof(struct rx_bd))
#define MAX_RX_DESC_CNT (RX_DESC_CNT - 1)
+#define MAX_TOTAL_RX_DESC_CNT (MAX_RX_DESC_CNT * MAX_RX_RINGS)
#define NEXT_TX_BD(x) (((x) & (MAX_TX_DESC_CNT - 1)) == \
(MAX_TX_DESC_CNT - 1)) ? \
(MAX_RX_DESC_CNT - 1)) ? \
(x) + 2 : (x) + 1
-#define RX_RING_IDX(x) ((x) & MAX_RX_DESC_CNT)
+#define RX_RING_IDX(x) ((x) & bp->rx_max_ring_idx)
+#define RX_RING(x) (((x) & ~MAX_RX_DESC_CNT) >> 8)
+#define RX_IDX(x) ((x) & MAX_RX_DESC_CNT)
/* Context size. */
#define CTX_SHIFT 7
#define BUFFERED_FLASH_PHY_PAGE_SIZE (1 << BUFFERED_FLASH_PAGE_BITS)
#define BUFFERED_FLASH_BYTE_ADDR_MASK (BUFFERED_FLASH_PHY_PAGE_SIZE-1)
#define BUFFERED_FLASH_PAGE_SIZE 264
-#define BUFFERED_FLASH_TOTAL_SIZE 131072
+#define BUFFERED_FLASH_TOTAL_SIZE 0x21000
#define SAIFUN_FLASH_PAGE_BITS 8
#define SAIFUN_FLASH_PHY_PAGE_SIZE (1 << SAIFUN_FLASH_PAGE_BITS)
#define SAIFUN_FLASH_PAGE_SIZE 256
#define SAIFUN_FLASH_BASE_TOTAL_SIZE 65536
+#define ST_MICRO_FLASH_PAGE_BITS 8
+#define ST_MICRO_FLASH_PHY_PAGE_SIZE (1 << ST_MICRO_FLASH_PAGE_BITS)
+#define ST_MICRO_FLASH_BYTE_ADDR_MASK (ST_MICRO_FLASH_PHY_PAGE_SIZE-1)
+#define ST_MICRO_FLASH_PAGE_SIZE 256
+#define ST_MICRO_FLASH_BASE_TOTAL_SIZE 65536
+
#define NVRAM_TIMEOUT_COUNT 30000
BNX2_NVM_CFG1_PROTECT_MODE | \
BNX2_NVM_CFG1_FLASH_SIZE)
+#define FLASH_BACKUP_STRAP_MASK (0xf << 26)
+
struct flash_spec {
u32 strapping;
u32 config1;
struct status_block *status_blk;
u32 last_status_idx;
- atomic_t tx_avail_bd;
- struct tx_bd *tx_desc_ring;
- struct sw_bd *tx_buf_ring;
- u32 tx_prod_bseq;
- u16 tx_prod;
- u16 tx_cons;
+ u32 flags;
+#define PCIX_FLAG 1
+#define PCI_32BIT_FLAG 2
+#define ONE_TDMA_FLAG 4 /* no longer used */
+#define NO_WOL_FLAG 8
+#define USING_DAC_FLAG 0x10
+#define USING_MSI_FLAG 0x20
+#define ASF_ENABLE_FLAG 0x40
+
+ /* Put tx producer and consumer fields in separate cache lines. */
+
+ u32 tx_prod_bseq __attribute__((aligned(L1_CACHE_BYTES)));
+ u16 tx_prod;
+
+ struct tx_bd *tx_desc_ring;
+ struct sw_bd *tx_buf_ring;
+ int tx_ring_size;
+
+ u16 tx_cons __attribute__((aligned(L1_CACHE_BYTES)));
+ u16 hw_tx_cons;
#ifdef BCM_VLAN
struct vlan_group *vlgrp;
u32 rx_offset;
u32 rx_buf_use_size; /* useable size */
u32 rx_buf_size; /* with alignment */
- struct rx_bd *rx_desc_ring;
- struct sw_bd *rx_buf_ring;
+ u32 rx_max_ring_idx;
+
u32 rx_prod_bseq;
u16 rx_prod;
u16 rx_cons;
+ u16 hw_rx_cons;
u32 rx_csum;
+ struct sw_bd *rx_buf_ring;
+ struct rx_bd *rx_desc_ring[MAX_RX_RINGS];
+
/* Only used to synchronize netif_stop_queue/wake_queue when tx */
/* ring is full */
spinlock_t tx_lock;
- /* End of fileds used in the performance code paths. */
+ /* End of fields used in the performance code paths. */
char *name;
int timer_interval;
+ int current_interval;
struct timer_list timer;
struct work_struct reset_task;
+ int in_reset_task;
/* Used to synchronize phy accesses. */
spinlock_t phy_lock;
- u32 flags;
-#define PCIX_FLAG 1
-#define PCI_32BIT_FLAG 2
-#define ONE_TDMA_FLAG 4 /* no longer used */
-#define NO_WOL_FLAG 8
-#define USING_DAC_FLAG 0x10
-#define USING_MSI_FLAG 0x20
-
u32 phy_flags;
#define PHY_SERDES_FLAG 1
#define PHY_CRC_FIX_FLAG 2
#define PHY_PARALLEL_DETECT_FLAG 4
+#define PHY_2_5G_CAPABLE_FLAG 8
#define PHY_INT_MODE_MASK_FLAG 0x300
#define PHY_INT_MODE_AUTO_POLLING_FLAG 0x100
#define PHY_INT_MODE_LINK_READY_FLAG 0x200
/* chip num:16-31, rev:12-15, metal:4-11, bond_id:0-3 */
#define CHIP_NUM(bp) (((bp)->chip_id) & 0xffff0000)
#define CHIP_NUM_5706 0x57060000
+#define CHIP_NUM_5708 0x57080000
#define CHIP_REV(bp) (((bp)->chip_id) & 0x0000f000)
#define CHIP_REV_Ax 0x00000000
#define CHIP_ID(bp) (((bp)->chip_id) & 0xfffffff0)
#define CHIP_ID_5706_A0 0x57060000
#define CHIP_ID_5706_A1 0x57060010
+#define CHIP_ID_5706_A2 0x57060020
+#define CHIP_ID_5708_A0 0x57080000
+#define CHIP_ID_5708_B0 0x57081000
+#define CHIP_ID_5708_B1 0x57081010
#define CHIP_BOND_ID(bp) (((bp)->chip_id) & 0xf)
u16 bus_speed_mhz;
u8 wol;
- u8 fw_timed_out;
+ u8 pad;
u16 fw_wr_seq;
u16 fw_drv_pulse_wr_seq;
- int tx_ring_size;
dma_addr_t tx_desc_mapping;
+ int rx_max_ring;
int rx_ring_size;
- dma_addr_t rx_desc_mapping;
+ dma_addr_t rx_desc_mapping[MAX_RX_RINGS];
u16 tx_quick_cons_trip;
u16 tx_quick_cons_trip_int;
struct statistics_block *stats_blk;
dma_addr_t stats_blk_mapping;
+ u32 hc_cmd;
u32 rx_mode;
u16 req_line_speed;
#define PHY_LOOPBACK 2
u8 serdes_an_pending;
-#define SERDES_AN_TIMEOUT (2 * HZ)
+#define SERDES_AN_TIMEOUT (HZ / 3)
u8 mac_addr[8];
+ u32 shmem_base;
+
u32 fw_ver;
int pm_cap;
struct net_device_stats net_stats;
struct flash_spec *flash_info;
+ u32 flash_size;
+
+ int status_stats_size;
};
static u32 bnx2_reg_rd_ind(struct bnx2 *bp, u32 offset);
* the firmware has timed out, the driver will assume there is no firmware
* running and there won't be any firmware-driver synchronization during a
* driver reset. */
-#define FW_ACK_TIME_OUT_MS 50
+#define FW_ACK_TIME_OUT_MS 100
#define BNX2_DRV_RESET_SIGNATURE 0x00000000
#define BNX2_FW_MSG_STATUS_FAILURE 0x00ff0000
#define BNX2_LINK_STATUS 0x0000000c
+#define BNX2_LINK_STATUS_INIT_VALUE 0xffffffff
+#define BNX2_LINK_STATUS_LINK_UP 0x1
+#define BNX2_LINK_STATUS_LINK_DOWN 0x0
+#define BNX2_LINK_STATUS_SPEED_MASK 0x1e
+#define BNX2_LINK_STATUS_AN_INCOMPLETE (0<<1)
+#define BNX2_LINK_STATUS_10HALF (1<<1)
+#define BNX2_LINK_STATUS_10FULL (2<<1)
+#define BNX2_LINK_STATUS_100HALF (3<<1)
+#define BNX2_LINK_STATUS_100BASE_T4 (4<<1)
+#define BNX2_LINK_STATUS_100FULL (5<<1)
+#define BNX2_LINK_STATUS_1000HALF (6<<1)
+#define BNX2_LINK_STATUS_1000FULL (7<<1)
+#define BNX2_LINK_STATUS_2500HALF (8<<1)
+#define BNX2_LINK_STATUS_2500FULL (9<<1)
+#define BNX2_LINK_STATUS_AN_ENABLED (1<<5)
+#define BNX2_LINK_STATUS_AN_COMPLETE (1<<6)
+#define BNX2_LINK_STATUS_PARALLEL_DET (1<<7)
+#define BNX2_LINK_STATUS_RESERVED (1<<8)
+#define BNX2_LINK_STATUS_PARTNER_AD_1000FULL (1<<9)
+#define BNX2_LINK_STATUS_PARTNER_AD_1000HALF (1<<10)
+#define BNX2_LINK_STATUS_PARTNER_AD_100BT4 (1<<11)
+#define BNX2_LINK_STATUS_PARTNER_AD_100FULL (1<<12)
+#define BNX2_LINK_STATUS_PARTNER_AD_100HALF (1<<13)
+#define BNX2_LINK_STATUS_PARTNER_AD_10FULL (1<<14)
+#define BNX2_LINK_STATUS_PARTNER_AD_10HALF (1<<15)
+#define BNX2_LINK_STATUS_TX_FC_ENABLED (1<<16)
+#define BNX2_LINK_STATUS_RX_FC_ENABLED (1<<17)
+#define BNX2_LINK_STATUS_PARTNER_SYM_PAUSE_CAP (1<<18)
+#define BNX2_LINK_STATUS_PARTNER_ASYM_PAUSE_CAP (1<<19)
+#define BNX2_LINK_STATUS_SERDES_LINK (1<<20)
+#define BNX2_LINK_STATUS_PARTNER_AD_2500FULL (1<<21)
+#define BNX2_LINK_STATUS_PARTNER_AD_2500HALF (1<<22)
#define BNX2_DRV_PULSE_MB 0x00000010
-#define BNX2_DRV_PULSE_SEQ_MASK 0x0000ffff
+#define BNX2_DRV_PULSE_SEQ_MASK 0x00007fff
/* Indicate to the firmware not to go into the
* OS absent when it is not getting driver pulse.
* This is used for debugging. */
-#define BNX2_DRV_MSG_DATA_PULSE_CODE_ALWAYS_ALIVE 0x00010000
+#define BNX2_DRV_MSG_DATA_PULSE_CODE_ALWAYS_ALIVE 0x00080000
#define BNX2_DEV_INFO_SIGNATURE 0x00000020
#define BNX2_DEV_INFO_SIGNATURE_MAGIC 0x44564900
#define BNX2_SHARED_HW_CFG_DESIGN_LOM 0x1
#define BNX2_SHARED_HW_CFG_PHY_COPPER 0
#define BNX2_SHARED_HW_CFG_PHY_FIBER 0x2
+#define BNX2_SHARED_HW_CFG_PHY_2_5G 0x20
+#define BNX2_SHARED_HW_CFG_PHY_BACKPLANE 0x40
#define BNX2_SHARED_HW_CFG_LED_MODE_SHIFT_BITS 8
#define BNX2_SHARED_HW_CFG_LED_MODE_MASK 0x300
#define BNX2_SHARED_HW_CFG_LED_MODE_MAC 0
#define BNX2_SHARED_HW_CFG_LED_MODE_GPHY1 0x100
#define BNX2_SHARED_HW_CFG_LED_MODE_GPHY2 0x200
+#define BNX2_SHARED_HW_CFG_CONFIG2 0x00000040
+#define BNX2_SHARED_HW_CFG2_NVM_SIZE_MASK 0x00fff000
+
#define BNX2_DEV_INFO_BC_REV 0x0000004c
#define BNX2_PORT_HW_CFG_MAC_UPPER 0x00000050
#define BNX2_PORT_HW_CFG_MAC_LOWER 0x00000054
#define BNX2_PORT_HW_CFG_CONFIG 0x00000058
+#define BNX2_PORT_HW_CFG_CFG_TXCTL3_MASK 0x0000ffff
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_MASK 0x001f0000
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_AN 0x00000000
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_1G 0x00030000
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_2_5G 0x00040000
#define BNX2_PORT_HW_CFG_IMD_MAC_A_UPPER 0x00000068
#define BNX2_PORT_HW_CFG_IMD_MAC_A_LOWER 0x0000006c
git://git.onelab.eu / linux-2.6.git / blobdiff