/*******************************************************************************
- Copyright(c) 1999 - 2006 Intel Corporation. All rights reserved.
+ Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
Contact Information:
Linux NICS <linux.nics@intel.com>
- e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*******************************************************************************/
#include "e1000.h"
+/* Change Log
+ * 6.3.9 12/16/2005
+ * o incorporate fix for recycled skbs from IBM LTC
+ * 6.3.7 11/18/2005
+ * o Honor eeprom setting for enabling/disabling Wake On Lan
+ * 6.3.5 11/17/2005
+ * o Fix memory leak in rx ring handling for PCI Express adapters
+ * 6.3.4 11/8/05
+ * o Patch from Jesper Juhl to remove redundant NULL checks for kfree
+ * 6.3.2 9/20/05
+ * o Render logic that sets/resets DRV_LOAD as inline functions to
+ * avoid code replication. If f/w is AMT then set DRV_LOAD only when
+ * network interface is open.
+ * o Handle DRV_LOAD set/reset in cases where AMT uses VLANs.
+ * o Adjust PBA partioning for Jumbo frames using MTU size and not
+ * rx_buffer_len
+ * 6.3.1 9/19/05
+ * o Use adapter->tx_timeout_factor in Tx Hung Detect logic
+ (e1000_clean_tx_irq)
+ * o Support for 8086:10B5 device (Quad Port)
+ * 6.2.14 9/15/05
+ * o In AMT enabled configurations, set/reset DRV_LOAD bit on interface
+ * open/close
+ * 6.2.13 9/14/05
+ * o Invoke e1000_check_mng_mode only for 8257x controllers since it
+ * accesses the FWSM that is not supported in other controllers
+ * 6.2.12 9/9/05
+ * o Add support for device id E1000_DEV_ID_82546GB_QUAD_COPPER
+ * o set RCTL:SECRC only for controllers newer than 82543.
+ * o When the n/w interface comes down reset DRV_LOAD bit to notify f/w.
+ * This code was moved from e1000_remove to e1000_close
+ * 6.2.10 9/6/05
+ * o Fix error in updating RDT in el1000_alloc_rx_buffers[_ps] -- one off.
+ * o Enable fc by default on 82573 controllers (do not read eeprom)
+ * o Fix rx_errors statistic not to include missed_packet_count
+ * o Fix rx_dropped statistic not to include missed_packet_count
+ (Padraig Brady)
+ * 6.2.9 8/30/05
+ * o Remove call to update statistics from the controller ib e1000_get_stats
+ * 6.2.8 8/30/05
+ * o Improved algorithm for rx buffer allocation/rdt update
+ * o Flow control watermarks relative to rx PBA size
+ * o Simplified 'Tx Hung' detect logic
+ * 6.2.7 8/17/05
+ * o Report rx buffer allocation failures and tx timeout counts in stats
+ * 6.2.6 8/16/05
+ * o Implement workaround for controller erratum -- linear non-tso packet
+ * following a TSO gets written back prematurely
+ * 6.2.5 8/15/05
+ * o Set netdev->tx_queue_len based on link speed/duplex settings.
+ * o Fix net_stats.rx_fifo_errors <p@draigBrady.com>
+ * o Do not power off PHY if SoL/IDER session is active
+ * 6.2.4 8/10/05
+ * o Fix loopback test setup/cleanup for 82571/3 controllers
+ * o Fix parsing of outgoing packets (e1000_transfer_dhcp_info) to treat
+ * all packets as raw
+ * o Prevent operations that will cause the PHY to be reset if SoL/IDER
+ * sessions are active and log a message
+ * 6.2.2 7/21/05
+ * o used fixed size descriptors for all MTU sizes, reduces memory load
+ * 6.1.2 4/13/05
+ * o Fixed ethtool diagnostics
+ * o Enabled flow control to take default eeprom settings
+ * o Added stats_lock around e1000_read_phy_reg commands to avoid concurrent
+ * calls, one from mii_ioctl and other from within update_stats while
+ * processing MIIREG ioctl.
+ */
+
char e1000_driver_name[] = "e1000";
static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
#ifndef CONFIG_E1000_NAPI
#else
#define DRIVERNAPI "-NAPI"
#endif
-#define DRV_VERSION "7.1.9-k4"DRIVERNAPI
+#define DRV_VERSION "6.3.9-k4"DRIVERNAPI
char e1000_driver_version[] = DRV_VERSION;
-static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
+static char e1000_copyright[] = "Copyright (c) 1999-2005 Intel Corporation.";
/* e1000_pci_tbl - PCI Device ID Table
*
INTEL_E1000_ETHERNET_DEVICE(0x1026),
INTEL_E1000_ETHERNET_DEVICE(0x1027),
INTEL_E1000_ETHERNET_DEVICE(0x1028),
- INTEL_E1000_ETHERNET_DEVICE(0x1049),
- INTEL_E1000_ETHERNET_DEVICE(0x104A),
- INTEL_E1000_ETHERNET_DEVICE(0x104B),
- INTEL_E1000_ETHERNET_DEVICE(0x104C),
- INTEL_E1000_ETHERNET_DEVICE(0x104D),
INTEL_E1000_ETHERNET_DEVICE(0x105E),
INTEL_E1000_ETHERNET_DEVICE(0x105F),
INTEL_E1000_ETHERNET_DEVICE(0x1060),
INTEL_E1000_ETHERNET_DEVICE(0x108A),
INTEL_E1000_ETHERNET_DEVICE(0x108B),
INTEL_E1000_ETHERNET_DEVICE(0x108C),
- INTEL_E1000_ETHERNET_DEVICE(0x1096),
- INTEL_E1000_ETHERNET_DEVICE(0x1098),
INTEL_E1000_ETHERNET_DEVICE(0x1099),
INTEL_E1000_ETHERNET_DEVICE(0x109A),
INTEL_E1000_ETHERNET_DEVICE(0x10B5),
- INTEL_E1000_ETHERNET_DEVICE(0x10B9),
- INTEL_E1000_ETHERNET_DEVICE(0x10BA),
- INTEL_E1000_ETHERNET_DEVICE(0x10BB),
/* required last entry */
{0,}
};
MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
+int e1000_up(struct e1000_adapter *adapter);
+void e1000_down(struct e1000_adapter *adapter);
+void e1000_reset(struct e1000_adapter *adapter);
+int e1000_set_spd_dplx(struct e1000_adapter *adapter, uint16_t spddplx);
+int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
+int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
+void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
+void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
- struct e1000_tx_ring *txdr);
+ struct e1000_tx_ring *txdr);
static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
- struct e1000_rx_ring *rxdr);
+ struct e1000_rx_ring *rxdr);
static void e1000_free_tx_resources(struct e1000_adapter *adapter,
- struct e1000_tx_ring *tx_ring);
+ struct e1000_tx_ring *tx_ring);
static void e1000_free_rx_resources(struct e1000_adapter *adapter,
- struct e1000_rx_ring *rx_ring);
+ struct e1000_rx_ring *rx_ring);
+void e1000_update_stats(struct e1000_adapter *adapter);
/* Local Function Prototypes */
static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
static void __devexit e1000_remove(struct pci_dev *pdev);
static int e1000_alloc_queues(struct e1000_adapter *adapter);
+#ifdef CONFIG_E1000_MQ
+static void e1000_setup_queue_mapping(struct e1000_adapter *adapter);
+#endif
static int e1000_sw_init(struct e1000_adapter *adapter);
static int e1000_open(struct net_device *netdev);
static int e1000_close(struct net_device *netdev);
static void e1000_set_multi(struct net_device *netdev);
static void e1000_update_phy_info(unsigned long data);
static void e1000_watchdog(unsigned long data);
+static void e1000_watchdog_task(struct e1000_adapter *adapter);
static void e1000_82547_tx_fifo_stall(unsigned long data);
static int e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
static struct net_device_stats * e1000_get_stats(struct net_device *netdev);
static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd);
static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
int cmd);
+void e1000_set_ethtool_ops(struct net_device *netdev);
static void e1000_enter_82542_rst(struct e1000_adapter *adapter);
static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
static void e1000_tx_timeout(struct net_device *dev);
-static void e1000_reset_task(struct net_device *dev);
+static void e1000_tx_timeout_task(struct net_device *dev);
static void e1000_smartspeed(struct e1000_adapter *adapter);
-static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
- struct sk_buff *skb);
+static inline int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
+ struct sk_buff *skb);
static void e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp);
static void e1000_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid);
static void e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
static void e1000_restore_vlan(struct e1000_adapter *adapter);
-static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
#ifdef CONFIG_PM
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
static int e1000_resume(struct pci_dev *pdev);
#endif
-static void e1000_shutdown(struct pci_dev *pdev);
#ifdef CONFIG_NET_POLL_CONTROLLER
/* for netdump / net console */
static void e1000_netpoll (struct net_device *netdev);
#endif
-static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
- pci_channel_state_t state);
-static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev);
-static void e1000_io_resume(struct pci_dev *pdev);
+#ifdef CONFIG_E1000_MQ
+/* for multiple Rx queues */
+void e1000_rx_schedule(void *data);
+#endif
-static struct pci_error_handlers e1000_err_handler = {
- .error_detected = e1000_io_error_detected,
- .slot_reset = e1000_io_slot_reset,
- .resume = e1000_io_resume,
-};
+/* Exported from other modules */
+
+extern void e1000_check_options(struct e1000_adapter *adapter);
static struct pci_driver e1000_driver = {
.name = e1000_driver_name,
.probe = e1000_probe,
.remove = __devexit_p(e1000_remove),
/* Power Managment Hooks */
- .suspend = e1000_suspend,
#ifdef CONFIG_PM
- .resume = e1000_resume,
+ .suspend = e1000_suspend,
+ .resume = e1000_resume
#endif
- .shutdown = e1000_shutdown,
- .err_handler = &e1000_err_handler
};
MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
module_exit(e1000_exit_module);
-static int e1000_request_irq(struct e1000_adapter *adapter)
-{
- struct net_device *netdev = adapter->netdev;
- int flags, err = 0;
-
- flags = IRQF_SHARED;
-#ifdef CONFIG_PCI_MSI
- if (adapter->hw.mac_type > e1000_82547_rev_2) {
- adapter->have_msi = TRUE;
- if ((err = pci_enable_msi(adapter->pdev))) {
- DPRINTK(PROBE, ERR,
- "Unable to allocate MSI interrupt Error: %d\n", err);
- adapter->have_msi = FALSE;
- }
- }
- if (adapter->have_msi)
- flags &= ~IRQF_SHARED;
-#endif
- if ((err = request_irq(adapter->pdev->irq, &e1000_intr, flags,
- netdev->name, netdev)))
- DPRINTK(PROBE, ERR,
- "Unable to allocate interrupt Error: %d\n", err);
-
- return err;
-}
-
-static void e1000_free_irq(struct e1000_adapter *adapter)
-{
- struct net_device *netdev = adapter->netdev;
-
- free_irq(adapter->pdev->irq, netdev);
-
-#ifdef CONFIG_PCI_MSI
- if (adapter->have_msi)
- pci_disable_msi(adapter->pdev);
-#endif
-}
-
/**
* e1000_irq_disable - Mask off interrupt generation on the NIC
* @adapter: board private structure
**/
-static void
+static inline void
e1000_irq_disable(struct e1000_adapter *adapter)
{
atomic_inc(&adapter->irq_sem);
* @adapter: board private structure
**/
-static void
+static inline void
e1000_irq_enable(struct e1000_adapter *adapter)
{
if (likely(atomic_dec_and_test(&adapter->irq_sem))) {
(vid != old_vid) &&
!adapter->vlgrp->vlan_devices[old_vid])
e1000_vlan_rx_kill_vid(netdev, old_vid);
- } else
- adapter->mng_vlan_id = vid;
+ }
}
}
* For ASF and Pass Through versions of f/w this means that the
* driver is no longer loaded. For AMT version (only with 82573) i
* of the f/w this means that the netowrk i/f is closed.
- *
+ *
**/
-static void
+static inline void
e1000_release_hw_control(struct e1000_adapter *adapter)
{
uint32_t ctrl_ext;
uint32_t swsm;
- uint32_t extcnf;
/* Let firmware taken over control of h/w */
switch (adapter->hw.mac_type) {
case e1000_82571:
case e1000_82572:
- case e1000_80003es2lan:
ctrl_ext = E1000_READ_REG(&adapter->hw, CTRL_EXT);
E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
swsm = E1000_READ_REG(&adapter->hw, SWSM);
E1000_WRITE_REG(&adapter->hw, SWSM,
swsm & ~E1000_SWSM_DRV_LOAD);
- case e1000_ich8lan:
- extcnf = E1000_READ_REG(&adapter->hw, CTRL_EXT);
- E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
- extcnf & ~E1000_CTRL_EXT_DRV_LOAD);
- break;
default:
break;
}
* @adapter: address of board private structure
*
* e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
- * For ASF and Pass Through versions of f/w this means that
- * the driver is loaded. For AMT version (only with 82573)
+ * For ASF and Pass Through versions of f/w this means that
+ * the driver is loaded. For AMT version (only with 82573)
* of the f/w this means that the netowrk i/f is open.
- *
+ *
**/
-static void
+static inline void
e1000_get_hw_control(struct e1000_adapter *adapter)
{
uint32_t ctrl_ext;
uint32_t swsm;
- uint32_t extcnf;
/* Let firmware know the driver has taken over */
switch (adapter->hw.mac_type) {
case e1000_82571:
case e1000_82572:
- case e1000_80003es2lan:
ctrl_ext = E1000_READ_REG(&adapter->hw, CTRL_EXT);
E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
E1000_WRITE_REG(&adapter->hw, SWSM,
swsm | E1000_SWSM_DRV_LOAD);
break;
- case e1000_ich8lan:
- extcnf = E1000_READ_REG(&adapter->hw, EXTCNF_CTRL);
- E1000_WRITE_REG(&adapter->hw, EXTCNF_CTRL,
- extcnf | E1000_EXTCNF_CTRL_SWFLAG);
- break;
default:
break;
}
e1000_up(struct e1000_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
- int i;
+ int i, err;
/* hardware has been reset, we need to reload some things */
+ /* Reset the PHY if it was previously powered down */
+ if (adapter->hw.media_type == e1000_media_type_copper) {
+ uint16_t mii_reg;
+ e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
+ if (mii_reg & MII_CR_POWER_DOWN)
+ e1000_phy_reset(&adapter->hw);
+ }
+
e1000_set_multi(netdev);
e1000_restore_vlan(adapter);
E1000_DESC_UNUSED(ring));
}
+#ifdef CONFIG_PCI_MSI
+ if (adapter->hw.mac_type > e1000_82547_rev_2) {
+ adapter->have_msi = TRUE;
+ if ((err = pci_enable_msi(adapter->pdev))) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate MSI interrupt Error: %d\n", err);
+ adapter->have_msi = FALSE;
+ }
+ }
+#endif
+ if ((err = request_irq(adapter->pdev->irq, &e1000_intr,
+ SA_SHIRQ | SA_SAMPLE_RANDOM,
+ netdev->name, netdev))) {
+ DPRINTK(PROBE, ERR,
+ "Unable to allocate interrupt Error: %d\n", err);
+ return err;
+ }
+
+#ifdef CONFIG_E1000_MQ
+ e1000_setup_queue_mapping(adapter);
+#endif
+
adapter->tx_queue_len = netdev->tx_queue_len;
mod_timer(&adapter->watchdog_timer, jiffies);
return 0;
}
-/**
- * e1000_power_up_phy - restore link in case the phy was powered down
- * @adapter: address of board private structure
- *
- * The phy may be powered down to save power and turn off link when the
- * driver is unloaded and wake on lan is not enabled (among others)
- * *** this routine MUST be followed by a call to e1000_reset ***
- *
- **/
-
-static void e1000_power_up_phy(struct e1000_adapter *adapter)
-{
- uint16_t mii_reg = 0;
-
- /* Just clear the power down bit to wake the phy back up */
- if (adapter->hw.media_type == e1000_media_type_copper) {
- /* according to the manual, the phy will retain its
- * settings across a power-down/up cycle */
- e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
- mii_reg &= ~MII_CR_POWER_DOWN;
- e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
- }
-}
-
-static void e1000_power_down_phy(struct e1000_adapter *adapter)
-{
- boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
- e1000_check_mng_mode(&adapter->hw);
- /* Power down the PHY so no link is implied when interface is down
- * The PHY cannot be powered down if any of the following is TRUE
- * (a) WoL is enabled
- * (b) AMT is active
- * (c) SoL/IDER session is active */
- if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
- adapter->hw.mac_type != e1000_ich8lan &&
- adapter->hw.media_type == e1000_media_type_copper &&
- !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
- !mng_mode_enabled &&
- !e1000_check_phy_reset_block(&adapter->hw)) {
- uint16_t mii_reg = 0;
- e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
- mii_reg |= MII_CR_POWER_DOWN;
- e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
- mdelay(1);
- }
-}
-
void
e1000_down(struct e1000_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
+ boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
+ e1000_check_mng_mode(&adapter->hw);
e1000_irq_disable(adapter);
-
+#ifdef CONFIG_E1000_MQ
+ while (atomic_read(&adapter->rx_sched_call_data.count) != 0);
+#endif
+ free_irq(adapter->pdev->irq, netdev);
+#ifdef CONFIG_PCI_MSI
+ if (adapter->hw.mac_type > e1000_82547_rev_2 &&
+ adapter->have_msi == TRUE)
+ pci_disable_msi(adapter->pdev);
+#endif
del_timer_sync(&adapter->tx_fifo_stall_timer);
del_timer_sync(&adapter->watchdog_timer);
del_timer_sync(&adapter->phy_info_timer);
e1000_reset(adapter);
e1000_clean_all_tx_rings(adapter);
e1000_clean_all_rx_rings(adapter);
-}
-void
-e1000_reinit_locked(struct e1000_adapter *adapter)
-{
- WARN_ON(in_interrupt());
- while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
- msleep(1);
- e1000_down(adapter);
- e1000_up(adapter);
- clear_bit(__E1000_RESETTING, &adapter->flags);
+ /* Power down the PHY so no link is implied when interface is down *
+ * The PHY cannot be powered down if any of the following is TRUE *
+ * (a) WoL is enabled
+ * (b) AMT is active
+ * (c) SoL/IDER session is active */
+ if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
+ adapter->hw.media_type == e1000_media_type_copper &&
+ !(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
+ !mng_mode_enabled &&
+ !e1000_check_phy_reset_block(&adapter->hw)) {
+ uint16_t mii_reg;
+ e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
+ mii_reg |= MII_CR_POWER_DOWN;
+ e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
+ mdelay(1);
+ }
}
void
break;
case e1000_82571:
case e1000_82572:
- case e1000_80003es2lan:
pba = E1000_PBA_38K;
break;
case e1000_82573:
pba = E1000_PBA_12K;
break;
- case e1000_ich8lan:
- pba = E1000_PBA_8K;
- break;
default:
pba = E1000_PBA_48K;
break;
/* Set the FC high water mark to 90% of the FIFO size.
* Required to clear last 3 LSB */
fc_high_water_mark = ((pba * 9216)/10) & 0xFFF8;
- /* We can't use 90% on small FIFOs because the remainder
- * would be less than 1 full frame. In this case, we size
- * it to allow at least a full frame above the high water
- * mark. */
- if (pba < E1000_PBA_16K)
- fc_high_water_mark = (pba * 1024) - 1600;
adapter->hw.fc_high_water = fc_high_water_mark;
adapter->hw.fc_low_water = fc_high_water_mark - 8;
- if (adapter->hw.mac_type == e1000_80003es2lan)
- adapter->hw.fc_pause_time = 0xFFFF;
- else
- adapter->hw.fc_pause_time = E1000_FC_PAUSE_TIME;
+ adapter->hw.fc_pause_time = E1000_FC_PAUSE_TIME;
adapter->hw.fc_send_xon = 1;
adapter->hw.fc = adapter->hw.original_fc;
e1000_reset_adaptive(&adapter->hw);
e1000_phy_get_info(&adapter->hw, &adapter->phy_info);
-
- if (!adapter->smart_power_down &&
- (adapter->hw.mac_type == e1000_82571 ||
- adapter->hw.mac_type == e1000_82572)) {
- uint16_t phy_data = 0;
- /* speed up time to link by disabling smart power down, ignore
- * the return value of this function because there is nothing
- * different we would do if it failed */
- e1000_read_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT,
- &phy_data);
- phy_data &= ~IGP02E1000_PM_SPD;
- e1000_write_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT,
- phy_data);
- }
-
- if (adapter->hw.mac_type < e1000_ich8lan)
- /* FIXME: this code is duplicate and wrong for PCI Express */
if (adapter->en_mng_pt) {
manc = E1000_READ_REG(&adapter->hw, MANC);
manc |= (E1000_MANC_ARP_EN | E1000_MANC_EN_MNG2HOST);
struct net_device *netdev;
struct e1000_adapter *adapter;
unsigned long mmio_start, mmio_len;
- unsigned long flash_start, flash_len;
static int cards_found = 0;
- static int e1000_ksp3_port_a = 0; /* global ksp3 port a indication */
int i, err, pci_using_dac;
uint16_t eeprom_data;
uint16_t eeprom_apme_mask = E1000_EEPROM_APME;
if ((err = pci_enable_device(pdev)))
return err;
- if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) &&
- !(err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK))) {
+ if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK))) {
pci_using_dac = 1;
} else {
- if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) &&
- (err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) {
+ if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) {
E1000_ERR("No usable DMA configuration, aborting\n");
return err;
}
if ((err = e1000_sw_init(adapter)))
goto err_sw_init;
- /* Flash BAR mapping must happen after e1000_sw_init
- * because it depends on mac_type */
- if ((adapter->hw.mac_type == e1000_ich8lan) &&
- (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
- flash_start = pci_resource_start(pdev, 1);
- flash_len = pci_resource_len(pdev, 1);
- adapter->hw.flash_address = ioremap(flash_start, flash_len);
- if (!adapter->hw.flash_address) {
- err = -EIO;
- goto err_flashmap;
- }
- }
-
if ((err = e1000_check_phy_reset_block(&adapter->hw)))
DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
- /* if ksp3, indicate if it's port a being setup */
- if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 &&
- e1000_ksp3_port_a == 0)
- adapter->ksp3_port_a = 1;
- e1000_ksp3_port_a++;
- /* Reset for multiple KP3 adapters */
- if (e1000_ksp3_port_a == 4)
- e1000_ksp3_port_a = 0;
-
if (adapter->hw.mac_type >= e1000_82543) {
netdev->features = NETIF_F_SG |
NETIF_F_HW_CSUM |
NETIF_F_HW_VLAN_TX |
NETIF_F_HW_VLAN_RX |
NETIF_F_HW_VLAN_FILTER;
- if (adapter->hw.mac_type == e1000_ich8lan)
- netdev->features &= ~NETIF_F_HW_VLAN_FILTER;
}
#ifdef NETIF_F_TSO
if (pci_using_dac)
netdev->features |= NETIF_F_HIGHDMA;
- netdev->features |= NETIF_F_LLTX;
-
+ /* hard_start_xmit is safe against parallel locking */
+ netdev->features |= NETIF_F_LLTX;
+
adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw);
- /* initialize eeprom parameters */
-
- if (e1000_init_eeprom_params(&adapter->hw)) {
- E1000_ERR("EEPROM initialization failed\n");
- return -EIO;
- }
-
/* before reading the EEPROM, reset the controller to
* put the device in a known good starting state */
adapter->watchdog_timer.function = &e1000_watchdog;
adapter->watchdog_timer.data = (unsigned long) adapter;
+ INIT_WORK(&adapter->watchdog_task,
+ (void (*)(void *))e1000_watchdog_task, adapter);
+
init_timer(&adapter->phy_info_timer);
adapter->phy_info_timer.function = &e1000_update_phy_info;
adapter->phy_info_timer.data = (unsigned long) adapter;
- INIT_WORK(&adapter->reset_task,
- (void (*)(void *))e1000_reset_task, netdev);
+ INIT_WORK(&adapter->tx_timeout_task,
+ (void (*)(void *))e1000_tx_timeout_task, netdev);
/* we're going to reset, so assume we have no link for now */
EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
eeprom_apme_mask = E1000_EEPROM_82544_APM;
break;
- case e1000_ich8lan:
- e1000_read_eeprom(&adapter->hw,
- EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data);
- eeprom_apme_mask = E1000_EEPROM_ICH8_APME;
- break;
case e1000_82546:
case e1000_82546_rev_3:
case e1000_82571:
- case e1000_80003es2lan:
if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1){
e1000_read_eeprom(&adapter->hw,
EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
return 0;
err_register:
- if (adapter->hw.flash_address)
- iounmap(adapter->hw.flash_address);
-err_flashmap:
err_sw_init:
err_eeprom:
iounmap(adapter->hw.hw_addr);
flush_scheduled_work();
if (adapter->hw.mac_type >= e1000_82540 &&
- adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper) {
manc = E1000_READ_REG(&adapter->hw, MANC);
if (manc & E1000_MANC_SMBUS_EN) {
unregister_netdev(netdev);
#ifdef CONFIG_E1000_NAPI
for (i = 0; i < adapter->num_rx_queues; i++)
- dev_put(&adapter->polling_netdev[i]);
+ __dev_put(&adapter->polling_netdev[i]);
#endif
if (!e1000_check_phy_reset_block(&adapter->hw))
#endif
iounmap(adapter->hw.hw_addr);
- if (adapter->hw.flash_address)
- iounmap(adapter->hw.flash_address);
pci_release_regions(pdev);
+#ifdef CONFIG_E1000_MQ
+ free_percpu(adapter->cpu_netdev);
+ free_percpu(adapter->cpu_tx_ring);
+#endif
free_netdev(netdev);
pci_disable_device(pdev);
pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
- adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
- adapter->rx_ps_bsize0 = E1000_RXBUFFER_128;
+ adapter->rx_buffer_len = E1000_RXBUFFER_2048;
+ adapter->rx_ps_bsize0 = E1000_RXBUFFER_256;
hw->max_frame_size = netdev->mtu +
ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
hw->min_frame_size = MINIMUM_ETHERNET_FRAME_SIZE;
return -EIO;
}
+ /* initialize eeprom parameters */
+
+ if (e1000_init_eeprom_params(hw)) {
+ E1000_ERR("EEPROM initialization failed\n");
+ return -EIO;
+ }
+
switch (hw->mac_type) {
default:
break;
hw->master_slave = E1000_MASTER_SLAVE;
}
+#ifdef CONFIG_E1000_MQ
+ /* Number of supported queues */
+ switch (hw->mac_type) {
+ case e1000_82571:
+ case e1000_82572:
+ /* These controllers support 2 tx queues, but with a single
+ * qdisc implementation, multiple tx queues aren't quite as
+ * interesting. If we can find a logical way of mapping
+ * flows to a queue, then perhaps we can up the num_tx_queue
+ * count back to its default. Until then, we run the risk of
+ * terrible performance due to SACK overload. */
+ adapter->num_tx_queues = 1;
+ adapter->num_rx_queues = 2;
+ break;
+ default:
+ adapter->num_tx_queues = 1;
+ adapter->num_rx_queues = 1;
+ break;
+ }
+ adapter->num_rx_queues = min(adapter->num_rx_queues, num_online_cpus());
+ adapter->num_tx_queues = min(adapter->num_tx_queues, num_online_cpus());
+ DPRINTK(DRV, INFO, "Multiqueue Enabled: Rx Queue count = %u %s\n",
+ adapter->num_rx_queues,
+ ((adapter->num_rx_queues == 1)
+ ? ((num_online_cpus() > 1)
+ ? "(due to unsupported feature in current adapter)"
+ : "(due to unsupported system configuration)")
+ : ""));
+ DPRINTK(DRV, INFO, "Multiqueue Enabled: Tx Queue count = %u\n",
+ adapter->num_tx_queues);
+#else
adapter->num_tx_queues = 1;
adapter->num_rx_queues = 1;
+#endif
if (e1000_alloc_queues(adapter)) {
DPRINTK(PROBE, ERR, "Unable to allocate memory for queues\n");
memset(adapter->polling_netdev, 0, size);
#endif
+#ifdef CONFIG_E1000_MQ
+ adapter->rx_sched_call_data.func = e1000_rx_schedule;
+ adapter->rx_sched_call_data.info = adapter->netdev;
+
+ adapter->cpu_netdev = alloc_percpu(struct net_device *);
+ adapter->cpu_tx_ring = alloc_percpu(struct e1000_tx_ring *);
+#endif
+
return E1000_SUCCESS;
}
+#ifdef CONFIG_E1000_MQ
+static void __devinit
+e1000_setup_queue_mapping(struct e1000_adapter *adapter)
+{
+ int i, cpu;
+
+ adapter->rx_sched_call_data.func = e1000_rx_schedule;
+ adapter->rx_sched_call_data.info = adapter->netdev;
+ cpus_clear(adapter->rx_sched_call_data.cpumask);
+
+ adapter->cpu_netdev = alloc_percpu(struct net_device *);
+ adapter->cpu_tx_ring = alloc_percpu(struct e1000_tx_ring *);
+
+ lock_cpu_hotplug();
+ i = 0;
+ for_each_online_cpu(cpu) {
+ *per_cpu_ptr(adapter->cpu_tx_ring, cpu) = &adapter->tx_ring[i % adapter->num_tx_queues];
+ /* This is incomplete because we'd like to assign separate
+ * physical cpus to these netdev polling structures and
+ * avoid saturating a subset of cpus.
+ */
+ if (i < adapter->num_rx_queues) {
+ *per_cpu_ptr(adapter->cpu_netdev, cpu) = &adapter->polling_netdev[i];
+ adapter->rx_ring[i].cpu = cpu;
+ cpu_set(cpu, adapter->cpumask);
+ } else
+ *per_cpu_ptr(adapter->cpu_netdev, cpu) = NULL;
+
+ i++;
+ }
+ unlock_cpu_hotplug();
+}
+#endif
+
/**
* e1000_open - Called when a network interface is made active
* @netdev: network interface device structure
struct e1000_adapter *adapter = netdev_priv(netdev);
int err;
- /* disallow open during test */
- if (test_bit(__E1000_DRIVER_TESTING, &adapter->flags))
- return -EBUSY;
-
/* allocate transmit descriptors */
if ((err = e1000_setup_all_tx_resources(adapter)))
if ((err = e1000_setup_all_rx_resources(adapter)))
goto err_setup_rx;
- err = e1000_request_irq(adapter);
- if (err)
- goto err_up;
-
- e1000_power_up_phy(adapter);
-
if ((err = e1000_up(adapter)))
goto err_up;
adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
{
struct e1000_adapter *adapter = netdev_priv(netdev);
- WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
e1000_down(adapter);
- e1000_power_down_phy(adapter);
- e1000_free_irq(adapter);
e1000_free_all_tx_resources(adapter);
e1000_free_all_rx_resources(adapter);
* @start: address of beginning of memory
* @len: length of memory
**/
-static boolean_t
+static inline boolean_t
e1000_check_64k_bound(struct e1000_adapter *adapter,
void *start, unsigned long len)
{
int size;
size = sizeof(struct e1000_buffer) * txdr->count;
- txdr->buffer_info = vmalloc(size);
+
+ txdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus));
if (!txdr->buffer_info) {
DPRINTK(PROBE, ERR,
"Unable to allocate memory for the transmit descriptor ring\n");
/* Setup the HW Tx Head and Tail descriptor pointers */
switch (adapter->num_tx_queues) {
+ case 2:
+ tdba = adapter->tx_ring[1].dma;
+ tdlen = adapter->tx_ring[1].count *
+ sizeof(struct e1000_tx_desc);
+ E1000_WRITE_REG(hw, TDBAL1, (tdba & 0x00000000ffffffffULL));
+ E1000_WRITE_REG(hw, TDBAH1, (tdba >> 32));
+ E1000_WRITE_REG(hw, TDLEN1, tdlen);
+ E1000_WRITE_REG(hw, TDH1, 0);
+ E1000_WRITE_REG(hw, TDT1, 0);
+ adapter->tx_ring[1].tdh = E1000_TDH1;
+ adapter->tx_ring[1].tdt = E1000_TDT1;
+ /* Fall Through */
case 1:
default:
tdba = adapter->tx_ring[0].dma;
tdlen = adapter->tx_ring[0].count *
sizeof(struct e1000_tx_desc);
- E1000_WRITE_REG(hw, TDLEN, tdlen);
- E1000_WRITE_REG(hw, TDBAH, (tdba >> 32));
E1000_WRITE_REG(hw, TDBAL, (tdba & 0x00000000ffffffffULL));
- E1000_WRITE_REG(hw, TDT, 0);
+ E1000_WRITE_REG(hw, TDBAH, (tdba >> 32));
+ E1000_WRITE_REG(hw, TDLEN, tdlen);
E1000_WRITE_REG(hw, TDH, 0);
- adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ? E1000_TDH : E1000_82542_TDH);
- adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ? E1000_TDT : E1000_82542_TDT);
+ E1000_WRITE_REG(hw, TDT, 0);
+ adapter->tx_ring[0].tdh = E1000_TDH;
+ adapter->tx_ring[0].tdt = E1000_TDT;
break;
}
ipgr1 = DEFAULT_82542_TIPG_IPGR1;
ipgr2 = DEFAULT_82542_TIPG_IPGR2;
break;
- case e1000_80003es2lan:
- ipgr1 = DEFAULT_82543_TIPG_IPGR1;
- ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2;
- break;
default:
ipgr1 = DEFAULT_82543_TIPG_IPGR1;
ipgr2 = DEFAULT_82543_TIPG_IPGR2;
tctl = E1000_READ_REG(hw, TCTL);
tctl &= ~E1000_TCTL_CT;
- tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
+ tctl |= E1000_TCTL_EN | E1000_TCTL_PSP | E1000_TCTL_RTLC |
(E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
-#ifdef DISABLE_MULR
- /* disable Multiple Reads for debugging */
- tctl &= ~E1000_TCTL_MULR;
-#endif
+ E1000_WRITE_REG(hw, TCTL, tctl);
if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) {
tarc = E1000_READ_REG(hw, TARC0);
else
tarc |= (1 << 28);
E1000_WRITE_REG(hw, TARC1, tarc);
- } else if (hw->mac_type == e1000_80003es2lan) {
- tarc = E1000_READ_REG(hw, TARC0);
- tarc |= 1;
- if (hw->media_type == e1000_media_type_internal_serdes)
- tarc |= (1 << 20);
- E1000_WRITE_REG(hw, TARC0, tarc);
- tarc = E1000_READ_REG(hw, TARC1);
- tarc |= 1;
- E1000_WRITE_REG(hw, TARC1, tarc);
}
e1000_config_collision_dist(hw);
if (hw->mac_type == e1000_82544 &&
hw->bus_type == e1000_bus_type_pcix)
adapter->pcix_82544 = 1;
-
- E1000_WRITE_REG(hw, TCTL, tctl);
-
}
/**
int size, desc_len;
size = sizeof(struct e1000_buffer) * rxdr->count;
- rxdr->buffer_info = vmalloc(size);
+ rxdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus));
if (!rxdr->buffer_info) {
DPRINTK(PROBE, ERR,
"Unable to allocate memory for the receive descriptor ring\n");
E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
(adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT);
+ if (adapter->hw.mac_type > e1000_82543)
+ rctl |= E1000_RCTL_SECRC;
+
if (adapter->hw.tbi_compatibility_on == 1)
rctl |= E1000_RCTL_SBP;
else
rctl |= E1000_RCTL_LPE;
/* Setup buffer sizes */
- rctl &= ~E1000_RCTL_SZ_4096;
- rctl |= E1000_RCTL_BSEX;
- switch (adapter->rx_buffer_len) {
- case E1000_RXBUFFER_256:
- rctl |= E1000_RCTL_SZ_256;
- rctl &= ~E1000_RCTL_BSEX;
- break;
- case E1000_RXBUFFER_512:
- rctl |= E1000_RCTL_SZ_512;
- rctl &= ~E1000_RCTL_BSEX;
- break;
- case E1000_RXBUFFER_1024:
- rctl |= E1000_RCTL_SZ_1024;
- rctl &= ~E1000_RCTL_BSEX;
- break;
+ if (adapter->hw.mac_type >= e1000_82571) {
+ /* We can now specify buffers in 1K increments.
+ * BSIZE and BSEX are ignored in this case. */
+ rctl |= adapter->rx_buffer_len << 0x11;
+ } else {
+ rctl &= ~E1000_RCTL_SZ_4096;
+ rctl |= E1000_RCTL_BSEX;
+ switch (adapter->rx_buffer_len) {
case E1000_RXBUFFER_2048:
default:
rctl |= E1000_RCTL_SZ_2048;
case E1000_RXBUFFER_16384:
rctl |= E1000_RCTL_SZ_16384;
break;
+ }
}
#ifndef CONFIG_E1000_DISABLE_PACKET_SPLIT
rfctl |= E1000_RFCTL_IPV6_DIS;
E1000_WRITE_REG(&adapter->hw, RFCTL, rfctl);
- rctl |= E1000_RCTL_DTYP_PS;
+ rctl |= E1000_RCTL_DTYP_PS | E1000_RCTL_SECRC;
psrctl |= adapter->rx_ps_bsize0 >>
E1000_PSRCTL_BSIZE0_SHIFT;
uint64_t rdba;
struct e1000_hw *hw = &adapter->hw;
uint32_t rdlen, rctl, rxcsum, ctrl_ext;
+#ifdef CONFIG_E1000_MQ
+ uint32_t reta, mrqc;
+ int i;
+#endif
if (adapter->rx_ps_pages) {
- /* this is a 32 byte descriptor */
rdlen = adapter->rx_ring[0].count *
sizeof(union e1000_rx_desc_packet_split);
adapter->clean_rx = e1000_clean_rx_irq_ps;
if (hw->mac_type >= e1000_82571) {
ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
/* Reset delay timers after every interrupt */
- ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
+ ctrl_ext |= E1000_CTRL_EXT_CANC;
#ifdef CONFIG_E1000_NAPI
/* Auto-Mask interrupts upon ICR read. */
ctrl_ext |= E1000_CTRL_EXT_IAME;
/* Setup the HW Rx Head and Tail Descriptor Pointers and
* the Base and Length of the Rx Descriptor Ring */
switch (adapter->num_rx_queues) {
+#ifdef CONFIG_E1000_MQ
+ case 2:
+ rdba = adapter->rx_ring[1].dma;
+ E1000_WRITE_REG(hw, RDBAL1, (rdba & 0x00000000ffffffffULL));
+ E1000_WRITE_REG(hw, RDBAH1, (rdba >> 32));
+ E1000_WRITE_REG(hw, RDLEN1, rdlen);
+ E1000_WRITE_REG(hw, RDH1, 0);
+ E1000_WRITE_REG(hw, RDT1, 0);
+ adapter->rx_ring[1].rdh = E1000_RDH1;
+ adapter->rx_ring[1].rdt = E1000_RDT1;
+ /* Fall Through */
+#endif
case 1:
default:
rdba = adapter->rx_ring[0].dma;
- E1000_WRITE_REG(hw, RDLEN, rdlen);
- E1000_WRITE_REG(hw, RDBAH, (rdba >> 32));
E1000_WRITE_REG(hw, RDBAL, (rdba & 0x00000000ffffffffULL));
- E1000_WRITE_REG(hw, RDT, 0);
+ E1000_WRITE_REG(hw, RDBAH, (rdba >> 32));
+ E1000_WRITE_REG(hw, RDLEN, rdlen);
E1000_WRITE_REG(hw, RDH, 0);
- adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ? E1000_RDH : E1000_82542_RDH);
- adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ? E1000_RDT : E1000_82542_RDT);
+ E1000_WRITE_REG(hw, RDT, 0);
+ adapter->rx_ring[0].rdh = E1000_RDH;
+ adapter->rx_ring[0].rdt = E1000_RDT;
break;
}
+#ifdef CONFIG_E1000_MQ
+ if (adapter->num_rx_queues > 1) {
+ uint32_t random[10];
+
+ get_random_bytes(&random[0], 40);
+
+ if (hw->mac_type <= e1000_82572) {
+ E1000_WRITE_REG(hw, RSSIR, 0);
+ E1000_WRITE_REG(hw, RSSIM, 0);
+ }
+
+ switch (adapter->num_rx_queues) {
+ case 2:
+ default:
+ reta = 0x00800080;
+ mrqc = E1000_MRQC_ENABLE_RSS_2Q;
+ break;
+ }
+
+ /* Fill out redirection table */
+ for (i = 0; i < 32; i++)
+ E1000_WRITE_REG_ARRAY(hw, RETA, i, reta);
+ /* Fill out hash function seeds */
+ for (i = 0; i < 10; i++)
+ E1000_WRITE_REG_ARRAY(hw, RSSRK, i, random[i]);
+
+ mrqc |= (E1000_MRQC_RSS_FIELD_IPV4 |
+ E1000_MRQC_RSS_FIELD_IPV4_TCP);
+ E1000_WRITE_REG(hw, MRQC, mrqc);
+ }
+
+ /* Multiqueue and packet checksumming are mutually exclusive. */
+ if (hw->mac_type >= e1000_82571) {
+ rxcsum = E1000_READ_REG(hw, RXCSUM);
+ rxcsum |= E1000_RXCSUM_PCSD;
+ E1000_WRITE_REG(hw, RXCSUM, rxcsum);
+ }
+
+#else
+
/* Enable 82543 Receive Checksum Offload for TCP and UDP */
if (hw->mac_type >= e1000_82543) {
rxcsum = E1000_READ_REG(hw, RXCSUM);
}
E1000_WRITE_REG(hw, RXCSUM, rxcsum);
}
+#endif /* CONFIG_E1000_MQ */
+
+ if (hw->mac_type == e1000_82573)
+ E1000_WRITE_REG(hw, ERT, 0x0100);
/* Enable Receives */
E1000_WRITE_REG(hw, RCTL, rctl);
e1000_free_tx_resources(adapter, &adapter->tx_ring[i]);
}
-static void
+static inline void
e1000_unmap_and_free_tx_resource(struct e1000_adapter *adapter,
struct e1000_buffer *buffer_info)
{
uint32_t rctl;
uint32_t hash_value;
int i, rar_entries = E1000_RAR_ENTRIES;
- int mta_reg_count = (hw->mac_type == e1000_ich8lan) ?
- E1000_NUM_MTA_REGISTERS_ICH8LAN :
- E1000_NUM_MTA_REGISTERS;
-
- if (adapter->hw.mac_type == e1000_ich8lan)
- rar_entries = E1000_RAR_ENTRIES_ICH8LAN;
/* reserve RAR[14] for LAA over-write work-around */
if (adapter->hw.mac_type == e1000_82571)
mc_ptr = mc_ptr->next;
} else {
E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0);
- E1000_WRITE_FLUSH(hw);
E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0);
- E1000_WRITE_FLUSH(hw);
}
}
/* clear the old settings from the multicast hash table */
- for (i = 0; i < mta_reg_count; i++) {
+ for (i = 0; i < E1000_NUM_MTA_REGISTERS; i++)
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
- E1000_WRITE_FLUSH(hw);
- }
/* load any remaining addresses into the hash table */
e1000_watchdog(unsigned long data)
{
struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+
+ /* Do the rest outside of interrupt context */
+ schedule_work(&adapter->watchdog_task);
+}
+
+static void
+e1000_watchdog_task(struct e1000_adapter *adapter)
+{
struct net_device *netdev = adapter->netdev;
struct e1000_tx_ring *txdr = adapter->tx_ring;
- uint32_t link, tctl;
- int32_t ret_val;
-
- ret_val = e1000_check_for_link(&adapter->hw);
- if ((ret_val == E1000_ERR_PHY) &&
- (adapter->hw.phy_type == e1000_phy_igp_3) &&
- (E1000_READ_REG(&adapter->hw, CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
- /* See e1000_kumeran_lock_loss_workaround() */
- DPRINTK(LINK, INFO,
- "Gigabit has been disabled, downgrading speed\n");
- }
+ uint32_t link;
+
+ e1000_check_for_link(&adapter->hw);
if (adapter->hw.mac_type == e1000_82573) {
e1000_enable_tx_pkt_filtering(&adapter->hw);
if (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id)
if (link) {
if (!netif_carrier_ok(netdev)) {
- boolean_t txb2b = 1;
e1000_get_speed_and_duplex(&adapter->hw,
&adapter->link_speed,
&adapter->link_duplex);
adapter->link_duplex == FULL_DUPLEX ?
"Full Duplex" : "Half Duplex");
- /* tweak tx_queue_len according to speed/duplex
- * and adjust the timeout factor */
+ /* tweak tx_queue_len according to speed/duplex */
netdev->tx_queue_len = adapter->tx_queue_len;
adapter->tx_timeout_factor = 1;
- switch (adapter->link_speed) {
- case SPEED_10:
- txb2b = 0;
- netdev->tx_queue_len = 10;
- adapter->tx_timeout_factor = 8;
- break;
- case SPEED_100:
- txb2b = 0;
- netdev->tx_queue_len = 100;
- /* maybe add some timeout factor ? */
- break;
- }
-
- if ((adapter->hw.mac_type == e1000_82571 ||
- adapter->hw.mac_type == e1000_82572) &&
- txb2b == 0) {
-#define SPEED_MODE_BIT (1 << 21)
- uint32_t tarc0;
- tarc0 = E1000_READ_REG(&adapter->hw, TARC0);
- tarc0 &= ~SPEED_MODE_BIT;
- E1000_WRITE_REG(&adapter->hw, TARC0, tarc0);
- }
-
-#ifdef NETIF_F_TSO
- /* disable TSO for pcie and 10/100 speeds, to avoid
- * some hardware issues */
- if (!adapter->tso_force &&
- adapter->hw.bus_type == e1000_bus_type_pci_express){
+ if (adapter->link_duplex == HALF_DUPLEX) {
switch (adapter->link_speed) {
case SPEED_10:
- case SPEED_100:
- DPRINTK(PROBE,INFO,
- "10/100 speed: disabling TSO\n");
- netdev->features &= ~NETIF_F_TSO;
- break;
- case SPEED_1000:
- netdev->features |= NETIF_F_TSO;
+ netdev->tx_queue_len = 10;
+ adapter->tx_timeout_factor = 8;
break;
- default:
- /* oops */
+ case SPEED_100:
+ netdev->tx_queue_len = 100;
break;
}
}
-#endif
-
- /* enable transmits in the hardware, need to do this
- * after setting TARC0 */
- tctl = E1000_READ_REG(&adapter->hw, TCTL);
- tctl |= E1000_TCTL_EN;
- E1000_WRITE_REG(&adapter->hw, TCTL, tctl);
netif_carrier_on(netdev);
netif_wake_queue(netdev);
netif_carrier_off(netdev);
netif_stop_queue(netdev);
mod_timer(&adapter->phy_info_timer, jiffies + 2 * HZ);
-
- /* 80003ES2LAN workaround--
- * For packet buffer work-around on link down event;
- * disable receives in the ISR and
- * reset device here in the watchdog
- */
- if (adapter->hw.mac_type == e1000_80003es2lan) {
- /* reset device */
- schedule_work(&adapter->reset_task);
- }
}
e1000_smartspeed(adapter);
e1000_update_adaptive(&adapter->hw);
+#ifdef CONFIG_E1000_MQ
+ txdr = *per_cpu_ptr(adapter->cpu_tx_ring, smp_processor_id());
+#endif
if (!netif_carrier_ok(netdev)) {
if (E1000_DESC_UNUSED(txdr) + 1 < txdr->count) {
/* We've lost link, so the controller stops DMA,
* but we've got queued Tx work that's never going
* to get done, so reset controller to flush Tx.
* (Do the reset outside of interrupt context). */
- adapter->tx_timeout_count++;
- schedule_work(&adapter->reset_task);
+ schedule_work(&adapter->tx_timeout_task);
}
}
#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
#define E1000_TX_FLAGS_VLAN_SHIFT 16
-static int
+static inline int
e1000_tso(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
struct sk_buff *skb)
{
uint8_t ipcss, ipcso, tucss, tucso, hdr_len;
int err;
- if (skb_is_gso(skb)) {
+ if (skb_shinfo(skb)->tso_size) {
if (skb_header_cloned(skb)) {
err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
if (err)
}
hdr_len = ((skb->h.raw - skb->data) + (skb->h.th->doff << 2));
- mss = skb_shinfo(skb)->gso_size;
- if (skb->protocol == htons(ETH_P_IP)) {
+ mss = skb_shinfo(skb)->tso_size;
+ if (skb->protocol == ntohs(ETH_P_IP)) {
skb->nh.iph->tot_len = 0;
skb->nh.iph->check = 0;
skb->h.th->check =
return FALSE;
}
-static boolean_t
+static inline boolean_t
e1000_tx_csum(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
struct sk_buff *skb)
{
#define E1000_MAX_TXD_PWR 12
#define E1000_MAX_DATA_PER_TXD (1<<E1000_MAX_TXD_PWR)
-static int
+static inline int
e1000_tx_map(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
struct sk_buff *skb, unsigned int first, unsigned int max_per_txd,
unsigned int nr_frags, unsigned int mss)
/* Workaround for Controller erratum --
* descriptor for non-tso packet in a linear SKB that follows a
* tso gets written back prematurely before the data is fully
- * DMA'd to the controller */
+ * DMAd to the controller */
if (!skb->data_len && tx_ring->last_tx_tso &&
- !skb_is_gso(skb)) {
+ !skb_shinfo(skb)->tso_size) {
tx_ring->last_tx_tso = 0;
size -= 4;
}
return count;
}
-static void
+static inline void
e1000_tx_queue(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
int tx_flags, int count)
{
#define E1000_FIFO_HDR 0x10
#define E1000_82547_PAD_LEN 0x3E0
-static int
+static inline int
e1000_82547_fifo_workaround(struct e1000_adapter *adapter, struct sk_buff *skb)
{
uint32_t fifo_space = adapter->tx_fifo_size - adapter->tx_fifo_head;
}
#define MINIMUM_DHCP_PACKET_SIZE 282
-static int
+static inline int
e1000_transfer_dhcp_info(struct e1000_adapter *adapter, struct sk_buff *skb)
{
struct e1000_hw *hw = &adapter->hw;
E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) )
return 0;
}
- if (skb->len > MINIMUM_DHCP_PACKET_SIZE) {
+ if ((skb->len > MINIMUM_DHCP_PACKET_SIZE) && (!skb->protocol)) {
struct ethhdr *eth = (struct ethhdr *) skb->data;
if ((htons(ETH_P_IP) == eth->h_proto)) {
const struct iphdr *ip =
unsigned int nr_frags = 0;
unsigned int mss = 0;
int count = 0;
- int tso;
+ int tso;
unsigned int f;
len -= skb->data_len;
+#ifdef CONFIG_E1000_MQ
+ tx_ring = *per_cpu_ptr(adapter->cpu_tx_ring, smp_processor_id());
+#else
tx_ring = adapter->tx_ring;
+#endif
if (unlikely(skb->len <= 0)) {
dev_kfree_skb_any(skb);
}
#ifdef NETIF_F_TSO
- mss = skb_shinfo(skb)->gso_size;
- /* The controller does a simple calculation to
+ mss = skb_shinfo(skb)->tso_size;
+ /* The controller does a simple calculation to
* make sure there is enough room in the FIFO before
* initiating the DMA for each buffer. The calc is:
* 4 = ceil(buffer len/mss). To make sure we don't
max_per_txd = min(mss << 2, max_per_txd);
max_txd_pwr = fls(max_per_txd) - 1;
- /* TSO Workaround for 82571/2/3 Controllers -- if skb->data
+ /* TSO Workaround for 82571/2 Controllers -- if skb->data
* points to just header, pull a few bytes of payload from
* frags into skb->data */
hdr_len = ((skb->h.raw - skb->data) + (skb->h.th->doff << 2));
- if (skb->data_len && (hdr_len == (skb->len - skb->data_len))) {
- switch (adapter->hw.mac_type) {
- unsigned int pull_size;
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_ich8lan:
- pull_size = min((unsigned int)4, skb->data_len);
- if (!__pskb_pull_tail(skb, pull_size)) {
- DPRINTK(DRV, ERR,
- "__pskb_pull_tail failed.\n");
- dev_kfree_skb_any(skb);
- return NETDEV_TX_OK;
- }
- len = skb->len - skb->data_len;
- break;
- default:
- /* do nothing */
- break;
+ if (skb->data_len && (hdr_len == (skb->len - skb->data_len)) &&
+ (adapter->hw.mac_type == e1000_82571 ||
+ adapter->hw.mac_type == e1000_82572)) {
+ unsigned int pull_size;
+ pull_size = min((unsigned int)4, skb->data_len);
+ if (!__pskb_pull_tail(skb, pull_size)) {
+ printk(KERN_ERR "__pskb_pull_tail failed.\n");
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
}
+ len = skb->len - skb->data_len;
}
}
#ifdef NETIF_F_TSO
/* Controller Erratum workaround */
- if (!skb->data_len && tx_ring->last_tx_tso && !skb_is_gso(skb))
+ if (!skb->data_len && tx_ring->last_tx_tso &&
+ !skb_shinfo(skb)->tso_size)
count++;
#endif
if (adapter->pcix_82544)
count += nr_frags;
-
- if (adapter->hw.tx_pkt_filtering &&
- (adapter->hw.mac_type == e1000_82573))
+ if (adapter->hw.tx_pkt_filtering && (adapter->hw.mac_type == e1000_82573) )
e1000_transfer_dhcp_info(adapter, skb);
local_irq_save(flags);
/* Old method was to assume IPv4 packet by default if TSO was enabled.
* 82571 hardware supports TSO capabilities for IPv6 as well...
* no longer assume, we must. */
- if (likely(skb->protocol == htons(ETH_P_IP)))
+ if (likely(skb->protocol == ntohs(ETH_P_IP)))
tx_flags |= E1000_TX_FLAGS_IPV4;
e1000_tx_queue(adapter, tx_ring, tx_flags,
struct e1000_adapter *adapter = netdev_priv(netdev);
/* Do the reset outside of interrupt context */
- adapter->tx_timeout_count++;
- schedule_work(&adapter->reset_task);
+ schedule_work(&adapter->tx_timeout_task);
}
static void
-e1000_reset_task(struct net_device *netdev)
+e1000_tx_timeout_task(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
- e1000_reinit_locked(adapter);
+ adapter->tx_timeout_count++;
+ e1000_down(adapter);
+ e1000_up(adapter);
}
/**
{
struct e1000_adapter *adapter = netdev_priv(netdev);
int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
- uint16_t eeprom_data = 0;
if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
(max_frame > MAX_JUMBO_FRAME_SIZE)) {
/* Adapter-specific max frame size limits. */
switch (adapter->hw.mac_type) {
- case e1000_undefined ... e1000_82542_rev2_1:
- case e1000_ich8lan:
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82573:
if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) {
DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
return -EINVAL;
}
break;
- case e1000_82573:
- /* only enable jumbo frames if ASPM is disabled completely
- * this means both bits must be zero in 0x1A bits 3:2 */
- e1000_read_eeprom(&adapter->hw, EEPROM_INIT_3GIO_3, 1,
- &eeprom_data);
- if (eeprom_data & EEPROM_WORD1A_ASPM_MASK) {
- if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) {
- DPRINTK(PROBE, ERR,
- "Jumbo Frames not supported.\n");
- return -EINVAL;
- }
- break;
- }
- /* fall through to get support */
case e1000_82571:
case e1000_82572:
- case e1000_80003es2lan:
#define MAX_STD_JUMBO_FRAME_SIZE 9234
if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
DPRINTK(PROBE, ERR, "MTU > 9216 not supported.\n");
break;
}
- /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
- * means we reserve 2 more, this pushes us to allocate from the next
- * larger slab size
- * i.e. RXBUFFER_2048 --> size-4096 slab */
-
- if (max_frame <= E1000_RXBUFFER_256)
- adapter->rx_buffer_len = E1000_RXBUFFER_256;
- else if (max_frame <= E1000_RXBUFFER_512)
- adapter->rx_buffer_len = E1000_RXBUFFER_512;
- else if (max_frame <= E1000_RXBUFFER_1024)
- adapter->rx_buffer_len = E1000_RXBUFFER_1024;
- else if (max_frame <= E1000_RXBUFFER_2048)
- adapter->rx_buffer_len = E1000_RXBUFFER_2048;
- else if (max_frame <= E1000_RXBUFFER_4096)
- adapter->rx_buffer_len = E1000_RXBUFFER_4096;
- else if (max_frame <= E1000_RXBUFFER_8192)
- adapter->rx_buffer_len = E1000_RXBUFFER_8192;
- else if (max_frame <= E1000_RXBUFFER_16384)
- adapter->rx_buffer_len = E1000_RXBUFFER_16384;
-
- /* adjust allocation if LPE protects us, and we aren't using SBP */
- if (!adapter->hw.tbi_compatibility_on &&
- ((max_frame == MAXIMUM_ETHERNET_FRAME_SIZE) ||
- (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
- adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+
+ if (adapter->hw.mac_type > e1000_82547_rev_2) {
+ adapter->rx_buffer_len = max_frame;
+ E1000_ROUNDUP(adapter->rx_buffer_len, 1024);
+ } else {
+ if(unlikely((adapter->hw.mac_type < e1000_82543) &&
+ (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE))) {
+ DPRINTK(PROBE, ERR, "Jumbo Frames not supported "
+ "on 82542\n");
+ return -EINVAL;
+ } else {
+ if(max_frame <= E1000_RXBUFFER_2048)
+ adapter->rx_buffer_len = E1000_RXBUFFER_2048;
+ else if(max_frame <= E1000_RXBUFFER_4096)
+ adapter->rx_buffer_len = E1000_RXBUFFER_4096;
+ else if(max_frame <= E1000_RXBUFFER_8192)
+ adapter->rx_buffer_len = E1000_RXBUFFER_8192;
+ else if(max_frame <= E1000_RXBUFFER_16384)
+ adapter->rx_buffer_len = E1000_RXBUFFER_16384;
+ }
+ }
netdev->mtu = new_mtu;
- if (netif_running(netdev))
- e1000_reinit_locked(adapter);
+ if (netif_running(netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ }
adapter->hw.max_frame_size = max_frame;
e1000_update_stats(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
- struct pci_dev *pdev = adapter->pdev;
unsigned long flags;
uint16_t phy_tmp;
#define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
- /*
- * Prevent stats update while adapter is being reset, or if the pci
- * connection is down.
- */
- if (adapter->link_speed == 0)
- return;
- if (pdev->error_state && pdev->error_state != pci_channel_io_normal)
- return;
-
spin_lock_irqsave(&adapter->stats_lock, flags);
/* these counters are modified from e1000_adjust_tbi_stats,
adapter->stats.bprc += E1000_READ_REG(hw, BPRC);
adapter->stats.mprc += E1000_READ_REG(hw, MPRC);
adapter->stats.roc += E1000_READ_REG(hw, ROC);
-
- if (adapter->hw.mac_type != e1000_ich8lan) {
adapter->stats.prc64 += E1000_READ_REG(hw, PRC64);
adapter->stats.prc127 += E1000_READ_REG(hw, PRC127);
adapter->stats.prc255 += E1000_READ_REG(hw, PRC255);
adapter->stats.prc511 += E1000_READ_REG(hw, PRC511);
adapter->stats.prc1023 += E1000_READ_REG(hw, PRC1023);
adapter->stats.prc1522 += E1000_READ_REG(hw, PRC1522);
- }
adapter->stats.symerrs += E1000_READ_REG(hw, SYMERRS);
adapter->stats.mpc += E1000_READ_REG(hw, MPC);
adapter->stats.totl += E1000_READ_REG(hw, TOTL);
adapter->stats.toth += E1000_READ_REG(hw, TOTH);
adapter->stats.tpr += E1000_READ_REG(hw, TPR);
-
- if (adapter->hw.mac_type != e1000_ich8lan) {
adapter->stats.ptc64 += E1000_READ_REG(hw, PTC64);
adapter->stats.ptc127 += E1000_READ_REG(hw, PTC127);
adapter->stats.ptc255 += E1000_READ_REG(hw, PTC255);
adapter->stats.ptc511 += E1000_READ_REG(hw, PTC511);
adapter->stats.ptc1023 += E1000_READ_REG(hw, PTC1023);
adapter->stats.ptc1522 += E1000_READ_REG(hw, PTC1522);
- }
-
adapter->stats.mptc += E1000_READ_REG(hw, MPTC);
adapter->stats.bptc += E1000_READ_REG(hw, BPTC);
if (hw->mac_type > e1000_82547_rev_2) {
adapter->stats.iac += E1000_READ_REG(hw, IAC);
adapter->stats.icrxoc += E1000_READ_REG(hw, ICRXOC);
-
- if (adapter->hw.mac_type != e1000_ich8lan) {
adapter->stats.icrxptc += E1000_READ_REG(hw, ICRXPTC);
adapter->stats.icrxatc += E1000_READ_REG(hw, ICRXATC);
adapter->stats.ictxptc += E1000_READ_REG(hw, ICTXPTC);
adapter->stats.ictxqec += E1000_READ_REG(hw, ICTXQEC);
adapter->stats.ictxqmtc += E1000_READ_REG(hw, ICTXQMTC);
adapter->stats.icrxdmtc += E1000_READ_REG(hw, ICRXDMTC);
- }
}
/* Fill out the OS statistics structure */
/* Rx Errors */
- /* RLEC on some newer hardware can be incorrect so build
- * our own version based on RUC and ROC */
adapter->net_stats.rx_errors = adapter->stats.rxerrc +
adapter->stats.crcerrs + adapter->stats.algnerrc +
- adapter->stats.ruc + adapter->stats.roc +
- adapter->stats.cexterr;
- adapter->net_stats.rx_length_errors = adapter->stats.ruc +
- adapter->stats.roc;
+ adapter->stats.rlec + adapter->stats.cexterr;
+ adapter->net_stats.rx_dropped = 0;
+ adapter->net_stats.rx_length_errors = adapter->stats.rlec;
adapter->net_stats.rx_crc_errors = adapter->stats.crcerrs;
adapter->net_stats.rx_frame_errors = adapter->stats.algnerrc;
adapter->net_stats.rx_missed_errors = adapter->stats.mpc;
spin_unlock_irqrestore(&adapter->stats_lock, flags);
}
+#ifdef CONFIG_E1000_MQ
+void
+e1000_rx_schedule(void *data)
+{
+ struct net_device *poll_dev, *netdev = data;
+ struct e1000_adapter *adapter = netdev->priv;
+ int this_cpu = get_cpu();
+
+ poll_dev = *per_cpu_ptr(adapter->cpu_netdev, this_cpu);
+ if (poll_dev == NULL) {
+ put_cpu();
+ return;
+ }
+
+ if (likely(netif_rx_schedule_prep(poll_dev)))
+ __netif_rx_schedule(poll_dev);
+ else
+ e1000_irq_enable(adapter);
+
+ put_cpu();
+}
+#endif
+
/**
* e1000_intr - Interrupt Handler
* @irq: interrupt number
struct net_device *netdev = data;
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- uint32_t rctl, icr = E1000_READ_REG(hw, ICR);
+ uint32_t icr = E1000_READ_REG(hw, ICR);
#ifndef CONFIG_E1000_NAPI
int i;
#else
if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) {
hw->get_link_status = 1;
- /* 80003ES2LAN workaround--
- * For packet buffer work-around on link down event;
- * disable receives here in the ISR and
- * reset adapter in watchdog
- */
- if (netif_carrier_ok(netdev) &&
- (adapter->hw.mac_type == e1000_80003es2lan)) {
- /* disable receives */
- rctl = E1000_READ_REG(hw, RCTL);
- E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
- }
mod_timer(&adapter->watchdog_timer, jiffies);
}
E1000_WRITE_REG(hw, IMC, ~0);
E1000_WRITE_FLUSH(hw);
}
- if (likely(netif_rx_schedule_prep(netdev)))
- __netif_rx_schedule(netdev);
+#ifdef CONFIG_E1000_MQ
+ if (atomic_read(&adapter->rx_sched_call_data.count) == 0) {
+ /* We must setup the cpumask once count == 0 since
+ * each cpu bit is cleared when the work is done. */
+ adapter->rx_sched_call_data.cpumask = adapter->cpumask;
+ atomic_add(adapter->num_rx_queues - 1, &adapter->irq_sem);
+ atomic_set(&adapter->rx_sched_call_data.count,
+ adapter->num_rx_queues);
+ smp_call_async_mask(&adapter->rx_sched_call_data);
+ } else {
+ printk("call_data.count == %u\n", atomic_read(&adapter->rx_sched_call_data.count));
+ }
+#else /* if !CONFIG_E1000_MQ */
+ if (likely(netif_rx_schedule_prep(&adapter->polling_netdev[0])))
+ __netif_rx_schedule(&adapter->polling_netdev[0]);
else
e1000_irq_enable(adapter);
-#else
+#endif /* CONFIG_E1000_MQ */
+
+#else /* if !CONFIG_E1000_NAPI */
/* Writing IMC and IMS is needed for 82547.
* Due to Hub Link bus being occupied, an interrupt
* de-assertion message is not able to be sent.
if (hw->mac_type == e1000_82547 || hw->mac_type == e1000_82547_rev_2)
e1000_irq_enable(adapter);
-#endif
+#endif /* CONFIG_E1000_NAPI */
return IRQ_HANDLED;
}
{
struct e1000_adapter *adapter;
int work_to_do = min(*budget, poll_dev->quota);
- int tx_cleaned = 0, work_done = 0;
+ int tx_cleaned = 0, i = 0, work_done = 0;
/* Must NOT use netdev_priv macro here. */
adapter = poll_dev->priv;
/* Keep link state information with original netdev */
- if (!netif_carrier_ok(poll_dev))
+ if (!netif_carrier_ok(adapter->netdev))
goto quit_polling;
- /* e1000_clean is called per-cpu. This lock protects
- * tx_ring[0] from being cleaned by multiple cpus
- * simultaneously. A failure obtaining the lock means
- * tx_ring[0] is currently being cleaned anyway. */
- if (spin_trylock(&adapter->tx_queue_lock)) {
- tx_cleaned = e1000_clean_tx_irq(adapter,
- &adapter->tx_ring[0]);
- spin_unlock(&adapter->tx_queue_lock);
- }
+ while (poll_dev != &adapter->polling_netdev[i]) {
+ i++;
+ if (unlikely(i == adapter->num_rx_queues))
+ BUG();
+ }
+
+ if (likely(adapter->num_tx_queues == 1)) {
+ /* e1000_clean is called per-cpu. This lock protects
+ * tx_ring[0] from being cleaned by multiple cpus
+ * simultaneously. A failure obtaining the lock means
+ * tx_ring[0] is currently being cleaned anyway. */
+ if (spin_trylock(&adapter->tx_queue_lock)) {
+ tx_cleaned = e1000_clean_tx_irq(adapter,
+ &adapter->tx_ring[0]);
+ spin_unlock(&adapter->tx_queue_lock);
+ }
+ } else
+ tx_cleaned = e1000_clean_tx_irq(adapter, &adapter->tx_ring[i]);
- adapter->clean_rx(adapter, &adapter->rx_ring[0],
+ adapter->clean_rx(adapter, &adapter->rx_ring[i],
&work_done, work_to_do);
*budget -= work_done;
/* If no Tx and not enough Rx work done, exit the polling mode */
if ((!tx_cleaned && (work_done == 0)) ||
- !netif_running(poll_dev)) {
+ !netif_running(adapter->netdev)) {
quit_polling:
netif_rx_complete(poll_dev);
e1000_irq_enable(adapter);
struct e1000_tx_desc *tx_desc, *eop_desc;
struct e1000_buffer *buffer_info;
unsigned int i, eop;
-#ifdef CONFIG_E1000_NAPI
- unsigned int count = 0;
-#endif
boolean_t cleaned = FALSE;
i = tx_ring->next_to_clean;
buffer_info = &tx_ring->buffer_info[i];
cleaned = (i == eop);
+#ifdef CONFIG_E1000_MQ
+ tx_ring->tx_stats.bytes += buffer_info->length;
+#endif
e1000_unmap_and_free_tx_resource(adapter, buffer_info);
memset(tx_desc, 0, sizeof(struct e1000_tx_desc));
if (unlikely(++i == tx_ring->count)) i = 0;
}
+#ifdef CONFIG_E1000_MQ
+ tx_ring->tx_stats.packets++;
+#endif
eop = tx_ring->buffer_info[i].next_to_watch;
eop_desc = E1000_TX_DESC(*tx_ring, eop);
-#ifdef CONFIG_E1000_NAPI
-#define E1000_TX_WEIGHT 64
- /* weight of a sort for tx, to avoid endless transmit cleanup */
- if (count++ == E1000_TX_WEIGHT) break;
-#endif
}
tx_ring->next_to_clean = i;
-#define TX_WAKE_THRESHOLD 32
+ spin_lock(&tx_ring->tx_lock);
+
if (unlikely(cleaned && netif_queue_stopped(netdev) &&
- netif_carrier_ok(netdev))) {
- spin_lock(&tx_ring->tx_lock);
- if (netif_queue_stopped(netdev) &&
- (E1000_DESC_UNUSED(tx_ring) >= TX_WAKE_THRESHOLD))
- netif_wake_queue(netdev);
- spin_unlock(&tx_ring->tx_lock);
- }
+ netif_carrier_ok(netdev)))
+ netif_wake_queue(netdev);
+
+ spin_unlock(&tx_ring->tx_lock);
if (adapter->detect_tx_hung) {
/* Detect a transmit hang in hardware, this serializes the
adapter->detect_tx_hung = FALSE;
if (tx_ring->buffer_info[eop].dma &&
time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
- (adapter->tx_timeout_factor * HZ))
+ adapter->tx_timeout_factor * HZ)
&& !(E1000_READ_REG(&adapter->hw, STATUS) &
E1000_STATUS_TXOFF)) {
* @sk_buff: socket buffer with received data
**/
-static void
+static inline void
e1000_rx_checksum(struct e1000_adapter *adapter,
uint32_t status_err, uint32_t csum,
struct sk_buff *skb)
buffer_info = &rx_ring->buffer_info[i];
while (rx_desc->status & E1000_RXD_STAT_DD) {
- struct sk_buff *skb;
+ struct sk_buff *skb, *next_skb;
u8 status;
#ifdef CONFIG_E1000_NAPI
if (*work_done >= work_to_do)
skb = buffer_info->skb;
buffer_info->skb = NULL;
- prefetch(skb->data - NET_IP_ALIGN);
-
if (++i == rx_ring->count) i = 0;
next_rxd = E1000_RX_DESC(*rx_ring, i);
- prefetch(next_rxd);
-
next_buffer = &rx_ring->buffer_info[i];
+ next_skb = next_buffer->skb;
cleaned = TRUE;
cleaned_count++;
length = le16_to_cpu(rx_desc->length);
- /* adjust length to remove Ethernet CRC */
- length -= 4;
-
if (unlikely(!(status & E1000_RXD_STAT_EOP))) {
/* All receives must fit into a single buffer */
E1000_DBG("%s: Receive packet consumed multiple"
" buffers\n", netdev->name);
- /* recycle */
- buffer_info-> skb = skb;
+ dev_kfree_skb_irq(skb);
goto next_desc;
}
flags);
length--;
} else {
- /* recycle */
- buffer_info->skb = skb;
+ dev_kfree_skb_irq(skb);
goto next_desc;
}
}
#define E1000_CB_LENGTH 256
if (length < E1000_CB_LENGTH) {
struct sk_buff *new_skb =
- netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
+ dev_alloc_skb(length + NET_IP_ALIGN);
if (new_skb) {
skb_reserve(new_skb, NET_IP_ALIGN);
new_skb->dev = netdev;
}
#endif /* CONFIG_E1000_NAPI */
netdev->last_rx = jiffies;
+#ifdef CONFIG_E1000_MQ
+ rx_ring->rx_stats.packets++;
+ rx_ring->rx_stats.bytes += length;
+#endif
next_desc:
rx_desc->status = 0;
cleaned_count = 0;
}
- /* use prefetched values */
rx_desc = next_rxd;
buffer_info = next_buffer;
}
struct e1000_buffer *buffer_info, *next_buffer;
struct e1000_ps_page *ps_page;
struct e1000_ps_page_dma *ps_page_dma;
- struct sk_buff *skb;
+ struct sk_buff *skb, *next_skb;
unsigned int i, j;
uint32_t length, staterr;
int cleaned_count = 0;
#endif
skb = buffer_info->skb;
- /* in the packet split case this is header only */
- prefetch(skb->data - NET_IP_ALIGN);
-
if (++i == rx_ring->count) i = 0;
next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
- prefetch(next_rxd);
-
next_buffer = &rx_ring->buffer_info[i];
+ next_skb = next_buffer->skb;
cleaned = TRUE;
cleaned_count++;
/* Good Receive */
skb_put(skb, length);
- {
- /* this looks ugly, but it seems compiler issues make it
- more efficient than reusing j */
- int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
-
- /* page alloc/put takes too long and effects small packet
- * throughput, so unsplit small packets and save the alloc/put*/
- if (l1 && ((length + l1) <= adapter->rx_ps_bsize0)) {
- u8 *vaddr;
- /* there is no documentation about how to call
- * kmap_atomic, so we can't hold the mapping
- * very long */
- pci_dma_sync_single_for_cpu(pdev,
- ps_page_dma->ps_page_dma[0],
- PAGE_SIZE,
- PCI_DMA_FROMDEVICE);
- vaddr = kmap_atomic(ps_page->ps_page[0],
- KM_SKB_DATA_SOFTIRQ);
- memcpy(skb->tail, vaddr, l1);
- kunmap_atomic(vaddr, KM_SKB_DATA_SOFTIRQ);
- pci_dma_sync_single_for_device(pdev,
- ps_page_dma->ps_page_dma[0],
- PAGE_SIZE, PCI_DMA_FROMDEVICE);
- /* remove the CRC */
- l1 -= 4;
- skb_put(skb, l1);
- goto copydone;
- } /* if */
- }
-
for (j = 0; j < adapter->rx_ps_pages; j++) {
- if (!(length= le16_to_cpu(rx_desc->wb.upper.length[j])))
+ if (!(length = le16_to_cpu(rx_desc->wb.upper.length[j])))
break;
+
pci_unmap_page(pdev, ps_page_dma->ps_page_dma[j],
PAGE_SIZE, PCI_DMA_FROMDEVICE);
ps_page_dma->ps_page_dma[j] = 0;
- skb_fill_page_desc(skb, j, ps_page->ps_page[j], 0,
- length);
+ skb_shinfo(skb)->frags[j].page =
+ ps_page->ps_page[j];
ps_page->ps_page[j] = NULL;
+ skb_shinfo(skb)->frags[j].page_offset = 0;
+ skb_shinfo(skb)->frags[j].size = length;
+ skb_shinfo(skb)->nr_frags++;
skb->len += length;
skb->data_len += length;
skb->truesize += length;
}
- /* strip the ethernet crc, problem is we're using pages now so
- * this whole operation can get a little cpu intensive */
- pskb_trim(skb, skb->len - 4);
-
-copydone:
e1000_rx_checksum(adapter, staterr,
le16_to_cpu(rx_desc->wb.lower.hi_dword.csum_ip.csum), skb);
skb->protocol = eth_type_trans(skb, netdev);
}
#endif /* CONFIG_E1000_NAPI */
netdev->last_rx = jiffies;
+#ifdef CONFIG_E1000_MQ
+ rx_ring->rx_stats.packets++;
+ rx_ring->rx_stats.bytes += length;
+#endif
next_desc:
rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
cleaned_count = 0;
}
- /* use prefetched values */
rx_desc = next_rxd;
buffer_info = next_buffer;
while (cleaned_count--) {
if (!(skb = buffer_info->skb))
- skb = netdev_alloc_skb(netdev, bufsz);
+ skb = dev_alloc_skb(bufsz);
else {
skb_trim(skb, 0);
goto map_skb;
}
+
if (unlikely(!skb)) {
/* Better luck next round */
adapter->alloc_rx_buff_failed++;
DPRINTK(RX_ERR, ERR, "skb align check failed: %u bytes "
"at %p\n", bufsz, skb->data);
/* Try again, without freeing the previous */
- skb = netdev_alloc_skb(netdev, bufsz);
+ skb = dev_alloc_skb(bufsz);
/* Failed allocation, critical failure */
if (!skb) {
dev_kfree_skb(oldskb);
rx_desc->read.buffer_addr[j+1] = ~0;
}
- skb = netdev_alloc_skb(netdev,
- adapter->rx_ps_bsize0 + NET_IP_ALIGN);
+ skb = dev_alloc_skb(adapter->rx_ps_bsize0 + NET_IP_ALIGN);
if (unlikely(!skb)) {
adapter->alloc_rx_buff_failed++;
spin_unlock_irqrestore(&adapter->stats_lock, flags);
return -EIO;
}
- if (adapter->hw.media_type == e1000_media_type_copper) {
+ if (adapter->hw.phy_type == e1000_phy_m88) {
switch (data->reg_num) {
case PHY_CTRL:
if (mii_reg & MII_CR_POWER_DOWN)
else
spddplx = SPEED_10;
spddplx += (mii_reg & 0x100)
- ? DUPLEX_FULL :
- DUPLEX_HALF;
+ ? FULL_DUPLEX :
+ HALF_DUPLEX;
retval = e1000_set_spd_dplx(adapter,
spddplx);
if (retval) {
return retval;
}
}
- if (netif_running(adapter->netdev))
- e1000_reinit_locked(adapter);
- else
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
e1000_reset(adapter);
break;
case M88E1000_PHY_SPEC_CTRL:
case PHY_CTRL:
if (mii_reg & MII_CR_POWER_DOWN)
break;
- if (netif_running(adapter->netdev))
- e1000_reinit_locked(adapter);
- else
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
e1000_reset(adapter);
break;
}
pci_write_config_word(adapter->pdev, reg, *value);
}
-#if 0
uint32_t
e1000_io_read(struct e1000_hw *hw, unsigned long port)
{
return inl(port);
}
-#endif /* 0 */
void
e1000_io_write(struct e1000_hw *hw, unsigned long port, uint32_t value)
ctrl |= E1000_CTRL_VME;
E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
- if (adapter->hw.mac_type != e1000_ich8lan) {
/* enable VLAN receive filtering */
rctl = E1000_READ_REG(&adapter->hw, RCTL);
rctl |= E1000_RCTL_VFE;
rctl &= ~E1000_RCTL_CFIEN;
E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
e1000_update_mng_vlan(adapter);
- }
} else {
/* disable VLAN tag insert/strip */
ctrl = E1000_READ_REG(&adapter->hw, CTRL);
ctrl &= ~E1000_CTRL_VME;
E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
- if (adapter->hw.mac_type != e1000_ich8lan) {
/* disable VLAN filtering */
rctl = E1000_READ_REG(&adapter->hw, RCTL);
rctl &= ~E1000_RCTL_VFE;
e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
}
- }
}
e1000_irq_enable(adapter);
}
#ifdef CONFIG_PM
-/* Save/restore 16 or 64 dwords of PCI config space depending on which
- * bus we're on (PCI(X) vs. PCI-E)
+/* these functions save and restore 16 or 64 dwords (64-256 bytes) of config
+ * space versus the 64 bytes that pci_[save|restore]_state handle
*/
#define PCIE_CONFIG_SPACE_LEN 256
#define PCI_CONFIG_SPACE_LEN 64
struct pci_dev *dev = adapter->pdev;
int size;
int i;
-
if (adapter->hw.mac_type >= e1000_82571)
size = PCIE_CONFIG_SPACE_LEN;
else
struct pci_dev *dev = adapter->pdev;
int size;
int i;
-
if (adapter->config_space == NULL)
return;
-
if (adapter->hw.mac_type >= e1000_82571)
size = PCIE_CONFIG_SPACE_LEN;
else
struct e1000_adapter *adapter = netdev_priv(netdev);
uint32_t ctrl, ctrl_ext, rctl, manc, status;
uint32_t wufc = adapter->wol;
-#ifdef CONFIG_PM
int retval = 0;
-#endif
netif_device_detach(netdev);
- if (netif_running(netdev)) {
- WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
+ if (netif_running(netdev))
e1000_down(adapter);
- }
#ifdef CONFIG_PM
- /* Implement our own version of pci_save_state(pdev) because pci-
- * express adapters have 256-byte config spaces. */
+ /* implement our own version of pci_save_state(pdev) because pci
+ * express adapters have larger 256 byte config spaces */
retval = e1000_pci_save_state(adapter);
if (retval)
return retval;
E1000_WRITE_REG(&adapter->hw, WUC, E1000_WUC_PME_EN);
E1000_WRITE_REG(&adapter->hw, WUFC, wufc);
- pci_enable_wake(pdev, PCI_D3hot, 1);
- pci_enable_wake(pdev, PCI_D3cold, 1);
+ retval = pci_enable_wake(pdev, PCI_D3hot, 1);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 wake\n");
+ retval = pci_enable_wake(pdev, PCI_D3cold, 1);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 cold wake\n");
} else {
E1000_WRITE_REG(&adapter->hw, WUC, 0);
E1000_WRITE_REG(&adapter->hw, WUFC, 0);
- pci_enable_wake(pdev, PCI_D3hot, 0);
- pci_enable_wake(pdev, PCI_D3cold, 0);
+ retval = pci_enable_wake(pdev, PCI_D3hot, 0);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 wake\n");
+ retval = pci_enable_wake(pdev, PCI_D3cold, 0); /* 4 == D3 cold */
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 cold wake\n");
}
- /* FIXME: this code is incorrect for PCI Express */
if (adapter->hw.mac_type >= e1000_82540 &&
- adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper) {
manc = E1000_READ_REG(&adapter->hw, MANC);
if (manc & E1000_MANC_SMBUS_EN) {
manc |= E1000_MANC_ARP_EN;
E1000_WRITE_REG(&adapter->hw, MANC, manc);
- pci_enable_wake(pdev, PCI_D3hot, 1);
- pci_enable_wake(pdev, PCI_D3cold, 1);
+ retval = pci_enable_wake(pdev, PCI_D3hot, 1);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 wake\n");
+ retval = pci_enable_wake(pdev, PCI_D3cold, 1);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 cold wake\n");
}
}
- if (adapter->hw.phy_type == e1000_phy_igp_3)
- e1000_phy_powerdown_workaround(&adapter->hw);
-
- if (netif_running(netdev))
- e1000_free_irq(adapter);
-
/* Release control of h/w to f/w. If f/w is AMT enabled, this
* would have already happened in close and is redundant. */
e1000_release_hw_control(adapter);
pci_disable_device(pdev);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ retval = pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error in setting power state\n");
return 0;
}
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct e1000_adapter *adapter = netdev_priv(netdev);
+ int retval;
uint32_t manc, ret_val;
- pci_set_power_state(pdev, PCI_D0);
+ retval = pci_set_power_state(pdev, PCI_D0);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error in setting power state\n");
e1000_pci_restore_state(adapter);
ret_val = pci_enable_device(pdev);
pci_set_master(pdev);
- pci_enable_wake(pdev, PCI_D3hot, 0);
- pci_enable_wake(pdev, PCI_D3cold, 0);
-
- if (netif_running(netdev) && (ret_val = e1000_request_irq(adapter)))
- return ret_val;
+ retval = pci_enable_wake(pdev, PCI_D3hot, 0);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 wake\n");
+ retval = pci_enable_wake(pdev, PCI_D3cold, 0);
+ if (retval)
+ DPRINTK(PROBE, ERR, "Error enabling D3 cold wake\n");
- e1000_power_up_phy(adapter);
e1000_reset(adapter);
E1000_WRITE_REG(&adapter->hw, WUS, ~0);
netif_device_attach(netdev);
- /* FIXME: this code is incorrect for PCI Express */
if (adapter->hw.mac_type >= e1000_82540 &&
- adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper) {
manc = E1000_READ_REG(&adapter->hw, MANC);
manc &= ~(E1000_MANC_ARP_EN);
return 0;
}
#endif
-
-static void e1000_shutdown(struct pci_dev *pdev)
-{
- e1000_suspend(pdev, PMSG_SUSPEND);
-}
-
#ifdef CONFIG_NET_POLL_CONTROLLER
/*
* Polling 'interrupt' - used by things like netconsole to send skbs
e1000_netpoll(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
-
disable_irq(adapter->pdev->irq);
e1000_intr(adapter->pdev->irq, netdev, NULL);
e1000_clean_tx_irq(adapter, adapter->tx_ring);
}
#endif
-/**
- * e1000_io_error_detected - called when PCI error is detected
- * @pdev: Pointer to PCI device
- * @state: The current pci conneection state
- *
- * This function is called after a PCI bus error affecting
- * this device has been detected.
- */
-static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev, pci_channel_state_t state)
-{
- struct net_device *netdev = pci_get_drvdata(pdev);
- struct e1000_adapter *adapter = netdev->priv;
-
- netif_device_detach(netdev);
-
- if (netif_running(netdev))
- e1000_down(adapter);
-
- /* Request a slot slot reset. */
- return PCI_ERS_RESULT_NEED_RESET;
-}
-
-/**
- * e1000_io_slot_reset - called after the pci bus has been reset.
- * @pdev: Pointer to PCI device
- *
- * Restart the card from scratch, as if from a cold-boot. Implementation
- * resembles the first-half of the e1000_resume routine.
- */
-static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
-{
- struct net_device *netdev = pci_get_drvdata(pdev);
- struct e1000_adapter *adapter = netdev->priv;
-
- if (pci_enable_device(pdev)) {
- printk(KERN_ERR "e1000: Cannot re-enable PCI device after reset.\n");
- return PCI_ERS_RESULT_DISCONNECT;
- }
- pci_set_master(pdev);
-
- pci_enable_wake(pdev, 3, 0);
- pci_enable_wake(pdev, 4, 0); /* 4 == D3 cold */
-
- /* Perform card reset only on one instance of the card */
- if (PCI_FUNC (pdev->devfn) != 0)
- return PCI_ERS_RESULT_RECOVERED;
-
- e1000_reset(adapter);
- E1000_WRITE_REG(&adapter->hw, WUS, ~0);
-
- return PCI_ERS_RESULT_RECOVERED;
-}
-
-/**
- * e1000_io_resume - called when traffic can start flowing again.
- * @pdev: Pointer to PCI device
- *
- * This callback is called when the error recovery driver tells us that
- * its OK to resume normal operation. Implementation resembles the
- * second-half of the e1000_resume routine.
- */
-static void e1000_io_resume(struct pci_dev *pdev)
-{
- struct net_device *netdev = pci_get_drvdata(pdev);
- struct e1000_adapter *adapter = netdev->priv;
- uint32_t manc, swsm;
-
- if (netif_running(netdev)) {
- if (e1000_up(adapter)) {
- printk("e1000: can't bring device back up after reset\n");
- return;
- }
- }
-
- netif_device_attach(netdev);
-
- if (adapter->hw.mac_type >= e1000_82540 &&
- adapter->hw.media_type == e1000_media_type_copper) {
- manc = E1000_READ_REG(&adapter->hw, MANC);
- manc &= ~(E1000_MANC_ARP_EN);
- E1000_WRITE_REG(&adapter->hw, MANC, manc);
- }
-
- switch (adapter->hw.mac_type) {
- case e1000_82573:
- swsm = E1000_READ_REG(&adapter->hw, SWSM);
- E1000_WRITE_REG(&adapter->hw, SWSM,
- swsm | E1000_SWSM_DRV_LOAD);
- break;
- default:
- break;
- }
-
- if (netif_running(netdev))
- mod_timer(&adapter->watchdog_timer, jiffies);
-}
-
/* e1000_main.c */
git://git.onelab.eu / linux-2.6.git / blobdiff