#undef HP100_MULTICAST_FILTER /* Need to be debugged... */
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/eisa.h>
#include <linux/pci.h>
+#include <linux/dma-mapping.h>
#include <linux/spinlock.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/bitops.h>
+#include <linux/jiffies.h>
#include <asm/io.h>
* Convert an address in a kernel buffer to a bus/phys/dma address.
* This work *only* for memory fragments part of lp->page_vaddr,
* because it was properly DMA allocated via pci_alloc_consistent(),
- * so we just need to "retreive" the original mapping to bus/phys/dma
+ * so we just need to "retrieve" the original mapping to bus/phys/dma
* address - Jean II */
static inline dma_addr_t virt_to_whatever(struct net_device *dev, u32 * ptr)
{
if (err)
goto out;
- err = register_netdev(dev);
- if (err)
- goto out1;
return dev;
- out1:
- release_region(dev->base_addr, HP100_REGION_SIZE);
out:
free_netdev(dev);
return ERR_PTR(err);
* Also, we can have EISA Busmaster cards (not tested),
* so beware !!! - Jean II */
if((bus == HP100_BUS_PCI) &&
- (pci_set_dma_mask(pci_dev, 0xffffffff))) {
+ (pci_set_dma_mask(pci_dev, DMA_32BIT_MASK))) {
/* Gracefully fallback to shared memory */
goto busmasterfail;
}
printk("Warning! Link down.\n");
}
+ err = register_netdev(dev);
+ if (err)
+ goto out3;
+
return 0;
+out3:
+ if (local_mode == 1)
+ pci_free_consistent(lp->pci_dev, MAX_RINGSIZE + 0x0f,
+ lp->page_vaddr_algn,
+ virt_to_whatever(dev, lp->page_vaddr_algn));
+ if (mem_ptr_virt)
+ iounmap(mem_ptr_virt);
out2:
release_region(ioaddr, HP100_REGION_SIZE);
out1:
- return -ENODEV;
+ return err;
}
/* This procedure puts the card into a stable init state */
printk("hp100: %s: start_xmit_bm: No TX PDL available.\n", dev->name);
#endif
/* not waited long enough since last tx? */
- if (jiffies - dev->trans_start < HZ)
+ if (time_before(jiffies, dev->trans_start + HZ))
return -EAGAIN;
if (hp100_check_lan(dev))
printk("hp100: %s: start_xmit: tx free mem = 0x%x\n", dev->name, i);
#endif
/* not waited long enough since last failed tx try? */
- if (jiffies - dev->trans_start < HZ) {
+ if (time_before(jiffies, dev->trans_start + HZ)) {
#ifdef HP100_DEBUG
printk("hp100: %s: trans_start timing problem\n",
dev->name);
hp100_outw(i, FRAGMENT_LEN); /* and first/only fragment length */
if (lp->mode == 2) { /* memory mapped */
- if (lp->mem_ptr_virt) { /* high pci memory was remapped */
- /* Note: The J2585B needs alignment to 32bits here! */
- memcpy_toio(lp->mem_ptr_virt, skb->data, (skb->len + 3) & ~3);
- if (!ok_flag)
- memset_io(lp->mem_ptr_virt, 0, HP100_MIN_PACKET_SIZE - skb->len);
- } else {
- /* Note: The J2585B needs alignment to 32bits here! */
- isa_memcpy_toio(lp->mem_ptr_phys, skb->data, (skb->len + 3) & ~3);
- if (!ok_flag)
- isa_memset_io(lp->mem_ptr_phys, 0, HP100_MIN_PACKET_SIZE - skb->len);
- }
+ /* Note: The J2585B needs alignment to 32bits here! */
+ memcpy_toio(lp->mem_ptr_virt, skb->data, (skb->len + 3) & ~3);
+ if (!ok_flag)
+ memset_io(lp->mem_ptr_virt, 0, HP100_MIN_PACKET_SIZE - skb->len);
} else { /* programmed i/o */
outsl(ioaddr + HP100_REG_DATA32, skb->data,
(skb->len + 3) >> 2);
/* First we get the header, which contains information about the */
/* actual length of the received packet. */
if (lp->mode == 2) { /* memory mapped mode */
- if (lp->mem_ptr_virt) /* if memory was remapped */
- header = readl(lp->mem_ptr_virt);
- else
- header = isa_readl(lp->mem_ptr_phys);
+ header = readl(lp->mem_ptr_virt);
} else /* programmed i/o */
header = hp100_inl(DATA32);
ptr = skb->data;
/* Now transfer the data from the card into that area */
- if (lp->mode == 2) {
- if (lp->mem_ptr_virt)
- memcpy_fromio(ptr, lp->mem_ptr_virt,pkt_len);
- /* Note alignment to 32bit transfers */
- else
- isa_memcpy_fromio(ptr, lp->mem_ptr_phys, pkt_len);
- } else /* io mapped */
+ if (lp->mode == 2)
+ memcpy_fromio(ptr, lp->mem_ptr_virt,pkt_len);
+ else /* io mapped */
insl(ioaddr + HP100_REG_DATA32, ptr, pkt_len >> 2);
skb->protocol = eth_type_trans(skb, dev);
do {
if (hp100_inb(VG_LAN_CFG_1) & HP100_LINK_CABLE_ST)
break;
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
if (time_after_eq(jiffies, time)) /* no signal->no logout */
do {
if (!(hp100_inb(VG_LAN_CFG_1) & HP100_LINK_UP_ST))
break;
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
#ifdef HP100_DEBUG
do {
if (!(hp100_inb(MAC_CFG_4) & HP100_MAC_SEL_ST))
break;
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
hp100_orb(HP100_AUTO_MODE, MAC_CFG_3); /* Autosel back on */
do {
if ((hp100_inb(VG_LAN_CFG_1) & HP100_LINK_CABLE_ST) == 0)
break;
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
if (time_before_eq(time, jiffies)) {
time = jiffies + (2 * HZ); /* This seems to take a while.... */
do {
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
return 0;
do {
if (~(hp100_inb(VG_LAN_CFG_1) & HP100_LINK_UP_ST))
break;
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
/* Start an addressed training and optionally request promiscuous port */
do {
if (hp100_inb(VG_LAN_CFG_1) & HP100_LINK_CABLE_ST)
break;
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_before(jiffies, time));
if (time_after_eq(jiffies, time)) {
#endif
break;
}
- if (!in_interrupt()) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- }
+ if (!in_interrupt())
+ schedule_timeout_interruptible(1);
} while (time_after(time, jiffies));
}
if (err)
goto out1;
- err = register_netdev(dev);
- if (err)
- goto out2;
-
#ifdef HP100_DEBUG
printk("hp100: %s: EISA adapter found at 0x%x\n", dev->name,
dev->base_addr);
#endif
gendev->driver_data = dev;
return 0;
- out2:
- release_region(dev->base_addr, HP100_REGION_SIZE);
out1:
free_netdev(dev);
return err;
err = hp100_probe1(dev, ioaddr, HP100_BUS_PCI, pdev);
if (err)
goto out1;
- err = register_netdev(dev);
- if (err)
- goto out2;
#ifdef HP100_DEBUG
printk("hp100: %s: PCI adapter found at 0x%x\n", dev->name, ioaddr);
#endif
pci_set_drvdata(pdev, dev);
return 0;
- out2:
- release_region(dev->base_addr, HP100_REGION_SIZE);
out1:
free_netdev(dev);
out0:
SET_MODULE_OWNER(dev);
err = hp100_isa_probe(dev, hp100_port[i]);
- if (!err) {
- err = register_netdev(dev);
- if (!err)
- hp100_devlist[cards++] = dev;
- else
- release_region(dev->base_addr, HP100_REGION_SIZE);
- }
-
- if (err)
+ if (!err)
+ hp100_devlist[cards++] = dev;
+ else
free_netdev(dev);
}
git://git.onelab.eu / linux-2.6.git / blobdiff