--- /dev/null
+#ifndef __MYRI10GE_MCP_H__
+#define __MYRI10GE_MCP_H__
+
+#define MXGEFW_VERSION_MAJOR 1
+#define MXGEFW_VERSION_MINOR 4
+
+/* 8 Bytes */
+struct mcp_dma_addr {
+ u32 high;
+ u32 low;
+};
+
+/* 4 Bytes */
+struct mcp_slot {
+ u16 checksum;
+ u16 length;
+};
+
+/* 64 Bytes */
+struct mcp_cmd {
+ u32 cmd;
+ u32 data0; /* will be low portion if data > 32 bits */
+ /* 8 */
+ u32 data1; /* will be high portion if data > 32 bits */
+ u32 data2; /* currently unused.. */
+ /* 16 */
+ struct mcp_dma_addr response_addr;
+ /* 24 */
+ u8 pad[40];
+};
+
+/* 8 Bytes */
+struct mcp_cmd_response {
+ u32 data;
+ u32 result;
+};
+
+/*
+ * flags used in mcp_kreq_ether_send_t:
+ *
+ * The SMALL flag is only needed in the first segment. It is raised
+ * for packets that are total less or equal 512 bytes.
+ *
+ * The CKSUM flag must be set in all segments.
+ *
+ * The PADDED flags is set if the packet needs to be padded, and it
+ * must be set for all segments.
+ *
+ * The MXGEFW_FLAGS_ALIGN_ODD must be set if the cumulative
+ * length of all previous segments was odd.
+ */
+
+#define MXGEFW_FLAGS_SMALL 0x1
+#define MXGEFW_FLAGS_TSO_HDR 0x1
+#define MXGEFW_FLAGS_FIRST 0x2
+#define MXGEFW_FLAGS_ALIGN_ODD 0x4
+#define MXGEFW_FLAGS_CKSUM 0x8
+#define MXGEFW_FLAGS_TSO_LAST 0x8
+#define MXGEFW_FLAGS_NO_TSO 0x10
+#define MXGEFW_FLAGS_TSO_CHOP 0x10
+#define MXGEFW_FLAGS_TSO_PLD 0x20
+
+#define MXGEFW_SEND_SMALL_SIZE 1520
+#define MXGEFW_MAX_MTU 9400
+
+union mcp_pso_or_cumlen {
+ u16 pseudo_hdr_offset;
+ u16 cum_len;
+};
+
+#define MXGEFW_MAX_SEND_DESC 12
+#define MXGEFW_PAD 2
+
+/* 16 Bytes */
+struct mcp_kreq_ether_send {
+ u32 addr_high;
+ u32 addr_low;
+ u16 pseudo_hdr_offset;
+ u16 length;
+ u8 pad;
+ u8 rdma_count;
+ u8 cksum_offset; /* where to start computing cksum */
+ u8 flags; /* as defined above */
+};
+
+/* 8 Bytes */
+struct mcp_kreq_ether_recv {
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* Commands */
+
+#define MXGEFW_CMD_OFFSET 0xf80000
+
+enum myri10ge_mcp_cmd_type {
+ MXGEFW_CMD_NONE = 0,
+ /* Reset the mcp, it is left in a safe state, waiting
+ * for the driver to set all its parameters */
+ MXGEFW_CMD_RESET,
+
+ /* get the version number of the current firmware..
+ * (may be available in the eeprom strings..? */
+ MXGEFW_GET_MCP_VERSION,
+
+ /* Parameters which must be set by the driver before it can
+ * issue MXGEFW_CMD_ETHERNET_UP. They persist until the next
+ * MXGEFW_CMD_RESET is issued */
+
+ MXGEFW_CMD_SET_INTRQ_DMA,
+ MXGEFW_CMD_SET_BIG_BUFFER_SIZE, /* in bytes, power of 2 */
+ MXGEFW_CMD_SET_SMALL_BUFFER_SIZE, /* in bytes */
+
+ /* Parameters which refer to lanai SRAM addresses where the
+ * driver must issue PIO writes for various things */
+
+ MXGEFW_CMD_GET_SEND_OFFSET,
+ MXGEFW_CMD_GET_SMALL_RX_OFFSET,
+ MXGEFW_CMD_GET_BIG_RX_OFFSET,
+ MXGEFW_CMD_GET_IRQ_ACK_OFFSET,
+ MXGEFW_CMD_GET_IRQ_DEASSERT_OFFSET,
+
+ /* Parameters which refer to rings stored on the MCP,
+ * and whose size is controlled by the mcp */
+
+ MXGEFW_CMD_GET_SEND_RING_SIZE, /* in bytes */
+ MXGEFW_CMD_GET_RX_RING_SIZE, /* in bytes */
+
+ /* Parameters which refer to rings stored in the host,
+ * and whose size is controlled by the host. Note that
+ * all must be physically contiguous and must contain
+ * a power of 2 number of entries. */
+
+ MXGEFW_CMD_SET_INTRQ_SIZE, /* in bytes */
+
+ /* command to bring ethernet interface up. Above parameters
+ * (plus mtu & mac address) must have been exchanged prior
+ * to issuing this command */
+ MXGEFW_CMD_ETHERNET_UP,
+
+ /* command to bring ethernet interface down. No further sends
+ * or receives may be processed until an MXGEFW_CMD_ETHERNET_UP
+ * is issued, and all interrupt queues must be flushed prior
+ * to ack'ing this command */
+
+ MXGEFW_CMD_ETHERNET_DOWN,
+
+ /* commands the driver may issue live, without resetting
+ * the nic. Note that increasing the mtu "live" should
+ * only be done if the driver has already supplied buffers
+ * sufficiently large to handle the new mtu. Decreasing
+ * the mtu live is safe */
+
+ MXGEFW_CMD_SET_MTU,
+ MXGEFW_CMD_GET_INTR_COAL_DELAY_OFFSET, /* in microseconds */
+ MXGEFW_CMD_SET_STATS_INTERVAL, /* in microseconds */
+ MXGEFW_CMD_SET_STATS_DMA,
+
+ MXGEFW_ENABLE_PROMISC,
+ MXGEFW_DISABLE_PROMISC,
+ MXGEFW_SET_MAC_ADDRESS,
+
+ MXGEFW_ENABLE_FLOW_CONTROL,
+ MXGEFW_DISABLE_FLOW_CONTROL,
+
+ /* do a DMA test
+ * data0,data1 = DMA address
+ * data2 = RDMA length (MSH), WDMA length (LSH)
+ * command return data = repetitions (MSH), 0.5-ms ticks (LSH)
+ */
+ MXGEFW_DMA_TEST
+};
+
+enum myri10ge_mcp_cmd_status {
+ MXGEFW_CMD_OK = 0,
+ MXGEFW_CMD_UNKNOWN,
+ MXGEFW_CMD_ERROR_RANGE,
+ MXGEFW_CMD_ERROR_BUSY,
+ MXGEFW_CMD_ERROR_EMPTY,
+ MXGEFW_CMD_ERROR_CLOSED,
+ MXGEFW_CMD_ERROR_HASH_ERROR,
+ MXGEFW_CMD_ERROR_BAD_PORT,
+ MXGEFW_CMD_ERROR_RESOURCES
+};
+
+/* 40 Bytes */
+struct mcp_irq_data {
+ u32 send_done_count;
+
+ u32 link_up;
+ u32 dropped_link_overflow;
+ u32 dropped_link_error_or_filtered;
+ u32 dropped_runt;
+ u32 dropped_overrun;
+ u32 dropped_no_small_buffer;
+ u32 dropped_no_big_buffer;
+ u32 rdma_tags_available;
+
+ u8 tx_stopped;
+ u8 link_down;
+ u8 stats_updated;
+ u8 valid;
+};
+
+#endif /* __MYRI10GE_MCP_H__ */
git://git.onelab.eu / linux-2.6.git / blobdiff