#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "1.4"
+#define DRV_VERSION "1.6.1"
#define PFX DRV_NAME " "
/*
if (hw->ports > 1)
reg1 |= PCI_Y2_PHY2_COMA;
}
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+ udelay(100);
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
sky2_write16(hw, B0_CTST, Y2_HW_WOL_ON);
sky2_pci_write32(hw, PCI_DEV_REG5, 0);
}
- sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
-
break;
case PCI_D3hot:
}
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
- if (hw->copper) {
+ if (sky2_is_copper(hw)) {
if (hw->chip_id == CHIP_ID_YUKON_FE) {
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
}
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
} else {
/* workaround for deviation #4.88 (CRC errors) */
/* disable Automatic Crossover */
ctrl &= ~PHY_M_PC_MDIX_MSK;
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+ }
- if (hw->chip_id == CHIP_ID_YUKON_XL) {
- /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
- gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
- ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
- ctrl &= ~PHY_M_MAC_MD_MSK;
- ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+ /* special setup for PHY 88E1112 Fiber */
+ if (hw->chip_id == CHIP_ID_YUKON_XL && !sky2_is_copper(hw)) {
+ pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+
+ /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl &= ~PHY_M_MAC_MD_MSK;
+ ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ if (hw->pmd_type == 'P') {
/* select page 1 to access Fiber registers */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
+
+ /* for SFP-module set SIGDET polarity to low */
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl |= PHY_M_FIB_SIGD_POL;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
}
+
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
adv = PHY_AN_CSMA;
if (sky2->autoneg == AUTONEG_ENABLE) {
- if (hw->copper) {
+ if (sky2_is_copper(hw)) {
if (sky2->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
adv |= PHY_M_AN_10_FD;
if (sky2->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
- } else /* special defines for FIBER (88E1011S only) */
- adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
+ } else { /* special defines for FIBER (88E1040S only) */
+ if (sky2->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_M_AN_1000X_AFD;
+ if (sky2->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_M_AN_1000X_AHD;
+ }
/* Set Flow-control capabilities */
if (sky2->tx_pause && sky2->rx_pause)
/*
* It appears the hardware has a bug in the FIFO logic that
* cause it to hang if the FIFO gets overrun and the receive buffer
- * is not aligned. ALso alloc_skb() won't align properly if slab
+ * is not aligned. Also dev_alloc_skb() won't align properly if slab
* debugging is enabled.
*/
static inline struct sk_buff *sky2_alloc_skb(unsigned int size, gfp_t gfp_mask)
{
struct sk_buff *skb;
- skb = alloc_skb(size + RX_SKB_ALIGN, gfp_mask);
+ skb = __dev_alloc_skb(size + RX_SKB_ALIGN, gfp_mask);
if (likely(skb)) {
unsigned long p = (unsigned long) skb->data;
skb_reserve(skb, ALIGN(p, RX_SKB_ALIGN) - p);
count = sizeof(dma_addr_t) / sizeof(u32);
count += skb_shinfo(skb)->nr_frags * count;
- if (skb_shinfo(skb)->tso_size)
+ if (skb_is_gso(skb))
++count;
if (skb->ip_summed == CHECKSUM_HW)
}
/* Check for TCP Segmentation Offload */
- mss = skb_shinfo(skb)->tso_size;
+ mss = skb_shinfo(skb)->gso_size;
if (mss != 0) {
/* just drop the packet if non-linear expansion fails */
if (skb_header_cloned(skb) &&
static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
{
- if (!hw->copper)
+ if (!sky2_is_copper(hw))
return SPEED_1000;
if (hw->chip_id == CHIP_ID_YUKON_FE)
goto oversize;
if (length < copybreak) {
- skb = alloc_skb(length + 2, GFP_ATOMIC);
+ skb = dev_alloc_skb(length + 2);
if (!skb)
goto resubmit;
}
}
+ /* Fully processed status ring so clear irq */
+ sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
+
exit_loop:
return work_done;
}
int work_done = 0;
u32 status = sky2_read32(hw, B0_Y2_SP_EISR);
- if (!~status)
- goto out;
-
if (status & Y2_IS_HW_ERR)
sky2_hw_intr(hw);
*budget -= work_done;
dev0->quota -= work_done;
- if (status & Y2_IS_STAT_BMU)
- sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
-
if (sky2_more_work(hw))
return 1;
-out:
+
netif_rx_complete(dev0);
sky2_read32(hw, B0_Y2_SP_LISR);
static int __devinit sky2_reset(struct sky2_hw *hw)
{
u16 status;
- u8 t8, pmd_type;
+ u8 t8;
int i;
sky2_write8(hw, B0_CTST, CS_RST_CLR);
sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
- pmd_type = sky2_read8(hw, B2_PMD_TYP);
- hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
-
+ hw->pmd_type = sky2_read8(hw, B2_PMD_TYP);
hw->ports = 1;
t8 = sky2_read8(hw, B2_Y2_HW_RES);
if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
static u32 sky2_supported_modes(const struct sky2_hw *hw)
{
- u32 modes;
- if (hw->copper) {
- modes = SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_Autoneg | SUPPORTED_TP;
+ if (sky2_is_copper(hw)) {
+ u32 modes = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_Autoneg | SUPPORTED_TP;
if (hw->chip_id != CHIP_ID_YUKON_FE)
modes |= SUPPORTED_1000baseT_Half
- | SUPPORTED_1000baseT_Full;
+ | SUPPORTED_1000baseT_Full;
+ return modes;
} else
- modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
- | SUPPORTED_Autoneg;
- return modes;
+ return SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full
+ | SUPPORTED_Autoneg
+ | SUPPORTED_FIBRE;
}
static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = sky2_supported_modes(hw);
ecmd->phy_address = PHY_ADDR_MARV;
- if (hw->copper) {
+ if (sky2_is_copper(hw)) {
ecmd->supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
| SUPPORTED_1000baseT_Full
| SUPPORTED_Autoneg | SUPPORTED_TP;
ecmd->port = PORT_TP;
- } else
+ ecmd->speed = sky2->speed;
+ } else {
+ ecmd->speed = SPEED_1000;
ecmd->port = PORT_FIBRE;
+ }
ecmd->advertising = sky2->advertising;
ecmd->autoneg = sky2->autoneg;
- ecmd->speed = sky2->speed;
ecmd->duplex = sky2->duplex;
return 0;
}
struct pci_dev *pdev = hw->pdev;
int err;
+ init_waitqueue_head (&hw->msi_wait);
+
sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW);
err = request_irq(pdev->irq, sky2_test_intr, SA_SHIRQ, DRV_NAME, hw);
return err;
}
- init_waitqueue_head (&hw->msi_wait);
-
sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ);
- wmb();
+ sky2_read8(hw, B0_CTST);
wait_event_timeout(hw->msi_wait, hw->msi_detected, HZ/10);
git://git.onelab.eu / linux-2.6.git / blobdiff