The driver will be compiled as a module: the
module will be called cosa.
-#
-# COMX drivers
-#
-# Not updated to 2.6.
-config COMX
- tristate "MultiGate (COMX) synchronous serial boards support"
- depends on WAN && (ISA || PCI) && BROKEN
- ---help---
- Drivers for the PC synchronous serial adapters by
- ITConsult-Pro Co, Hungary.
-
- Read <file:Documentation/networking/comx.txt> for help on configuring
- and using COMX interfaces. Further info on these cards can be found
- at <http://www.itc.hu/> or <info@itc.hu>.
-
- Say Y if you want to use any board from the MultiGate (COMX)
- family, you must also say Y to "/proc file system support"
- (CONFIG_PROC_FS) in order to use these drivers.
-
- To compile this driver as a module, choose M here: the
- module will be called comx.
-
-config COMX_HW_COMX
- tristate "Support for COMX/CMX/HiCOMX boards"
- depends on COMX
- help
- Driver for the 'CMX', 'COMX' and 'HiCOMX' boards.
-
- You will need additional firmware to use these cards, which are
- downloadable from <ftp://ftp.itc.hu/>.
-
- Say Y if you have a board like this.
-
- To compile this driver as a module, choose M here: the
- module will be called comx-hw-comx.
-
-config COMX_HW_LOCOMX
- tristate "Support for LoCOMX board"
- depends on COMX
- help
- Driver for the 'LoCOMX' board.
-
- Say Y if you have a board like this.
-
- To compile this driver as a module, choose M here: the
- module will be called comx-hw-locomx.
-
-config COMX_HW_MIXCOM
- tristate "Support for MixCOM board"
- depends on COMX
- ---help---
- Driver for the 'MixCOM' board.
-
- If you want to use the watchdog device on this card, you should
- select it in the Watchdog Cards section of the Character Devices
- configuration. The ISDN interface of this card is Teles 16.3
- compatible, you should enable it in the ISDN configuration menu. The
- driver for the flash ROM of this card is available separately on
- <ftp://ftp.itc.hu/>.
-
- Say Y if you have a board like this.
-
- To compile this driver as a module, choose M here: the
- module will be called comx-hw-mixcom.
-
-config COMX_HW_MUNICH
- tristate "Support for MUNICH based boards: SliceCOM, PCICOM (WelCOM)"
- depends on COMX
- ---help---
- Driver for the 'SliceCOM' (channelized E1) and 'PciCOM' (X21) boards.
-
- Read <file:Documentation/networking/slicecom.txt> for help on
- configuring and using SliceCOM interfaces. Further info on these
- cards can be found at <http://www.itc.hu> or <info@itc.hu>.
-
- Say Y if you have a board like this.
-
- To compile this driver as a module, choose M here: the
- module will be called comx-hw-munich.
-
-config COMX_PROTO_PPP
- tristate "Support for HDLC and syncPPP protocols on MultiGate boards"
- depends on COMX
- help
- Cisco-HDLC and synchronous PPP protocol driver.
-
- Say Y if you want to use either protocol.
-
- To compile this as a module, choose M here: the
- module will be called comx-proto-ppp.
-
-config COMX_PROTO_LAPB
- tristate "Support for LAPB protocol on MultiGate boards"
- depends on WAN && (COMX!=n && LAPB=m && LAPB || LAPB=y && COMX)
- help
- LAPB protocol driver.
-
- Say Y if you want to use this protocol.
-
- To compile this as a module, choose M here: the
- module will be called comx-proto-lapb.
-
-config COMX_PROTO_FR
- tristate "Support for Frame Relay on MultiGate boards"
- depends on COMX
- help
- Frame Relay protocol driver.
-
- Say Y if you want to use this protocol.
-
- To compile this as a module, choose M here: the
- module will be called comx-proto-fr.
-
config DSCC4
tristate "Etinc PCISYNC serial board support"
depends on WAN && PCI && m
git://git.onelab.eu / linux-2.6.git / blobdiff