* under either the MPL or the GPL. */
/*
- * v0.01 -> v0.02 - 21/3/2001 - Jean II
- * o Allow to use regular ethX device name instead of dldwdX
- * o Warning on IBSS with ESSID=any for firmware 6.06
- * o Put proper range.throughput values (optimistic)
- * o IWSPY support (IOCTL and stat gather in Rx path)
- * o Allow setting frequency in Ad-Hoc mode
- * o Disable WEP setting if !has_wep to work on old firmware
- * o Fix txpower range
- * o Start adding support for Samsung/Compaq firmware
- *
- * v0.02 -> v0.03 - 23/3/2001 - Jean II
- * o Start adding Symbol support - need to check all that
- * o Fix Prism2/Symbol WEP to accept 128 bits keys
- * o Add Symbol WEP (add authentication type)
- * o Add Prism2/Symbol rate
- * o Add PM timeout (holdover duration)
- * o Enable "iwconfig eth0 key off" and friends (toggle flags)
- * o Enable "iwconfig eth0 power unicast/all" (toggle flags)
- * o Try with an Intel card. It report firmware 1.01, behave like
- * an antiquated firmware, however on windows it says 2.00. Yuck !
- * o Workaround firmware bug in allocate buffer (Intel 1.01)
- * o Finish external renaming to orinoco...
- * o Testing with various Wavelan firmwares
- *
- * v0.03 -> v0.04 - 30/3/2001 - Jean II
- * o Update to Wireless 11 -> add retry limit/lifetime support
- * o Tested with a D-Link DWL 650 card, fill in firmware support
- * o Warning on Vcc mismatch (D-Link 3.3v card in Lucent 5v only slot)
- * o Fixed the Prism2 WEP bugs that I introduced in v0.03 :-(
- * It works on D-Link *only* after a tcpdump. Weird...
- * And still doesn't work on Intel card. Grrrr...
- * o Update the mode after a setport3
- * o Add preamble setting for Symbol cards (not yet enabled)
- * o Don't complain as much about Symbol cards...
- *
- * v0.04 -> v0.04b - 22/4/2001 - David Gibson
- * o Removed the 'eth' parameter - always use ethXX as the
- * interface name instead of dldwdXX. The other was racy
- * anyway.
- * o Clean up RID definitions in hermes.h, other cleanups
- *
- * v0.04b -> v0.04c - 24/4/2001 - Jean II
- * o Tim Hurley <timster AT seiki.bliztech.com> reported a D-Link card
- * with vendor 02 and firmware 0.08. Added in the capabilities...
- * o Tested Lucent firmware 7.28, everything works...
- *
- * v0.04c -> v0.05 - 3/5/2001 - Benjamin Herrenschmidt
- * o Spin-off Pcmcia code. This file is renamed orinoco.c,
- * and orinoco_cs.c now contains only the Pcmcia specific stuff
- * o Add Airport driver support on top of orinoco.c (see airport.c)
- *
- * v0.05 -> v0.05a - 4/5/2001 - Jean II
- * o Revert to old Pcmcia code to fix breakage of Ben's changes...
- *
- * v0.05a -> v0.05b - 4/5/2001 - Jean II
- * o add module parameter 'ignore_cis_vcc' for D-Link @ 5V
- * o D-Link firmware doesn't support multicast. We just print a few
- * error messages, but otherwise everything works...
- * o For David : set/getport3 works fine, just upgrade iwpriv...
- *
- * v0.05b -> v0.05c - 5/5/2001 - Benjamin Herrenschmidt
- * o Adapt airport.c to latest changes in orinoco.c
- * o Remove deferred power enabling code
- *
- * v0.05c -> v0.05d - 5/5/2001 - Jean II
- * o Workaround to SNAP decapsulate frame from Linksys AP
- * original patch from : Dong Liu <dliu AT research.bell-labs.com>
- * (note : the memcmp bug was mine - fixed)
- * o Remove set_retry stuff, no firmware support it (bloat--).
- *
- * v0.05d -> v0.06 - 25/5/2001 - Jean II
- * Original patch from "Hong Lin" <alin AT redhat.com>,
- * "Ian Kinner" <ikinner AT redhat.com>
- * and "David Smith" <dsmith AT redhat.com>
- * o Init of priv->tx_rate_ctrl in firmware specific section.
- * o Prism2/Symbol rate, upto should be 0xF and not 0x15. Doh !
- * o Spectrum card always need cor_reset (for every reset)
- * o Fix cor_reset to not lose bit 7 in the register
- * o flush_stale_links to remove zombie Pcmcia instances
- * o Ack previous hermes event before reset
- * Me (with my little hands)
- * o Allow orinoco.c to call cor_reset via priv->card_reset_handler
- * o Add priv->need_card_reset to toggle this feature
- * o Fix various buglets when setting WEP in Symbol firmware
- * Now, encryption is fully functional on Symbol cards. Youpi !
- *
- * v0.06 -> v0.06b - 25/5/2001 - Jean II
- * o IBSS on Symbol use port_mode = 4. Please don't ask...
- *
- * v0.06b -> v0.06c - 29/5/2001 - Jean II
- * o Show first spy address in /proc/net/wireless for IBSS mode as well
- *
- * v0.06c -> v0.06d - 6/7/2001 - David Gibson
- * o Change a bunch of KERN_INFO messages to KERN_DEBUG, as per Linus'
- * wishes to reduce the number of unnecessary messages.
- * o Removed bogus message on CRC error.
- * o Merged fixes for v0.08 Prism 2 firmware from William Waghorn
- * <willwaghorn AT yahoo.co.uk>
- * o Slight cleanup/re-arrangement of firmware detection code.
- *
- * v0.06d -> v0.06e - 1/8/2001 - David Gibson
- * o Removed some redundant global initializers (orinoco_cs.c).
- * o Added some module metadata
- *
- * v0.06e -> v0.06f - 14/8/2001 - David Gibson
- * o Wording fix to license
- * o Added a 'use_alternate_encaps' module parameter for APs which need an
- * oui of 00:00:00. We really need a better way of handling this, but
- * the module flag is better than nothing for now.
- *
- * v0.06f -> v0.07 - 20/8/2001 - David Gibson
- * o Removed BAP error retries from hermes_bap_seek(). For Tx we now
- * let the upper layers handle the retry, we retry explicitly in the
- * Rx path, but don't make as much noise about it.
- * o Firmware detection cleanups.
- *
- * v0.07 -> v0.07a - 1/10/3001 - Jean II
- * o Add code to read Symbol firmware revision, inspired by latest code
- * in Spectrum24 by Lee John Keyser-Allen - Thanks Lee !
- * o Thanks to Jared Valentine <hidden AT xmission.com> for "providing" me
- * a 3Com card with a recent firmware, fill out Symbol firmware
- * capabilities of latest rev (2.20), as well as older Symbol cards.
- * o Disable Power Management in newer Symbol firmware, the API
- * has changed (documentation needed).
- *
- * v0.07a -> v0.08 - 3/10/2001 - David Gibson
- * o Fixed a possible buffer overrun found by the Stanford checker (in
- * dldwd_ioctl_setiwencode()). Can only be called by root anyway, so not
- * a big problem.
- * o Turned has_big_wep on for Intersil cards. That's not true for all of
- * them but we should at least let the capable ones try.
- * o Wait for BUSY to clear at the beginning of hermes_bap_seek(). I
- * realized that my assumption that the driver's serialization
- * would prevent the BAP being busy on entry was possibly false, because
- * things other than seeks may make the BAP busy.
- * o Use "alternate" (oui 00:00:00) encapsulation by default.
- * Setting use_old_encaps will mimic the old behaviour, but I think we
- * will be able to eliminate this.
- * o Don't try to make __initdata const (the version string). This can't
- * work because of the way the __initdata sectioning works.
- * o Added MODULE_LICENSE tags.
- * o Support for PLX (transparent PCMCIA->PCI bridge) cards.
- * o Changed to using the new type-fascist min/max.
- *
- * v0.08 -> v0.08a - 9/10/2001 - David Gibson
- * o Inserted some missing acknowledgements/info into the Changelog.
- * o Fixed some bugs in the normalization of signal level reporting.
- * o Fixed bad bug in WEP key handling on Intersil and Symbol firmware,
- * which led to an instant crash on big-endian machines.
- *
- * v0.08a -> v0.08b - 20/11/2001 - David Gibson
- * o Lots of cleanup and bugfixes in orinoco_plx.c
- * o Cleanup to handling of Tx rate setting.
- * o Removed support for old encapsulation method.
- * o Removed old "dldwd" names.
- * o Split RID constants into a new file hermes_rid.h
- * o Renamed RID constants to match linux-wlan-ng and prism2.o
- * o Bugfixes in hermes.c
- * o Poke the PLX's INTCSR register, so it actually starts
- * generating interrupts. These cards might actually work now.
- * o Update to wireless extensions v12 (Jean II)
- * o Support for tallies and inquire command (Jean II)
- * o Airport updates for newer PPC kernels (BenH)
- *
- * v0.08b -> v0.09 - 21/12/2001 - David Gibson
- * o Some new PCI IDs for PLX cards.
- * o Removed broken attempt to do ALLMULTI reception. Just use
- * promiscuous mode instead
- * o Preliminary work for list-AP (Jean II)
- * o Airport updates from (BenH)
- * o Eliminated racy hw_ready stuff
- * o Fixed generation of fake events in irq handler. This should
- * finally kill the EIO problems (Jean II & dgibson)
- * o Fixed breakage of bitrate set/get on Agere firmware (Jean II)
- *
- * v0.09 -> v0.09a - 2/1/2002 - David Gibson
- * o Fixed stupid mistake in multicast list handling, triggering
- * a BUG()
- *
- * v0.09a -> v0.09b - 16/1/2002 - David Gibson
- * o Fixed even stupider mistake in new interrupt handling, which
- * seriously broke things on big-endian machines.
- * o Removed a bunch of redundant includes and exports.
- * o Removed a redundant MOD_{INC,DEC}_USE_COUNT pair in airport.c
- * o Don't attempt to do hardware level multicast reception on
- * Intersil firmware, just go promisc instead.
- * o Typo fixed in hermes_issue_cmd()
- * o Eliminated WIRELESS_SPY #ifdefs
- * o Status code reported on Tx exceptions
- * o Moved netif_wake_queue() from ALLOC interrupts to TX and TXEXC
- * interrupts, which should fix the timeouts we're seeing.
- *
- * v0.09b -> v0.10 - 25 Feb 2002 - David Gibson
- * o Removed nested structures used for header parsing, so the
- * driver should now work without hackery on ARM
- * o Fix for WEP handling on Intersil (Hawk Newton)
- * o Eliminated the /proc/hermes/ethXX/regs debugging file. It
- * was never very useful.
- * o Make Rx errors less noisy.
- *
- * v0.10 -> v0.11 - 5 Apr 2002 - David Gibson
- * o Laid the groundwork in hermes.[ch] for devices which map
- * into PCI memory space rather than IO space.
- * o Fixed bug in multicast handling (cleared multicast list when
- * leaving promiscuous mode).
- * o Relegated Tx error messages to debug.
- * o Cleaned up / corrected handling of allocation lengths.
- * o Set OWNSSID in IBSS mode for WinXP interoperability (jimc).
- * o Change to using alloc_etherdev() for structure allocations.
- * o Check for and drop undersized packets.
- * o Fixed a race in stopping/waking the queue. This should fix
- * the timeout problems (Pavel Roskin)
- * o Reverted to netif_wake_queue() on the ALLOC event.
- * o Fixes for recent Symbol firmwares which lack AP density
- * (Pavel Roskin).
- *
- * v0.11 -> v0.11a - 29 Apr 2002 - David Gibson
- * o Handle different register spacing, necessary for Prism 2.5
- * PCI adaptors (Steve Hill).
- * o Cleaned up initialization of card structures in orinoco_cs
- * and airport. Removed card->priv field.
- * o Make response structure optional for hermes_docmd_wait()
- * Pavel Roskin)
- * o Added PCI id for Nortel emobility to orinoco_plx.c.
- * o Cleanup to handling of Symbol's allocation bug. (Pavel Roskin)
- * o Cleanups to firmware capability detection.
- * o Arrange for orinoco_pci.c to override firmware detection.
- * We should be able to support the PCI Intersil cards now.
- * o Cleanup handling of reset_cor and hard_reset (Pavel Roskin).
- * o Remove erroneous use of USER_BAP in the TxExc handler (Jouni
- * Malinen).
- * o Makefile changes for better integration into David Hinds
- * pcmcia-cs package.
- *
- * v0.11a -> v0.11b - 1 May 2002 - David Gibson
- * o Better error reporting in orinoco_plx_init_one()
- * o Fixed multiple bad kfree() bugs introduced by the
- * alloc_orinocodev() changes.
- *
- * v0.11b -> v0.12 - 19 Jun 2002 - David Gibson
- * o Support changing the MAC address.
- * o Correct display of Intersil firmware revision numbers.
- * o Entirely revised locking scheme. Should be both simpler and
- * better.
- * o Merged some common code in orinoco_plx, orinoco_pci and
- * airport by creating orinoco_default_{open,stop,reset}()
- * which are used as the dev->open, dev->stop, priv->reset
- * callbacks if none are specified when alloc_orinocodev() is
- * called.
- * o Removed orinoco_plx_interrupt() and orinoco_pci_interrupt().
- * They didn't do anything.
- *
- * v0.12 -> v0.12a - 4 Jul 2002 - David Gibson
- * o Some rearrangement of code.
- * o Numerous fixups to locking and rest handling, particularly
- * for PCMCIA.
- * o This allows open and stop net_device methods to be in
- * orinoco.c now, rather than in the init modules.
- * o In orinoco_cs.c link->priv now points to the struct
- * net_device not to the struct orinoco_private.
- * o Added a check for undersized SNAP frames, which could cause
- * crashes.
- *
- * v0.12a -> v0.12b - 11 Jul 2002 - David Gibson
- * o Fix hw->num_init testing code, so num_init is actually
- * incremented.
- * o Fix very stupid bug in orinoco_cs which broke compile with
- * CONFIG_SMP.
- * o Squashed a warning.
- *
- * v0.12b -> v0.12c - 26 Jul 2002 - David Gibson
- * o Change to C9X style designated initializers.
- * o Add support for 3Com AirConnect PCI.
- * o No longer ignore the hard_reset argument to
- * alloc_orinocodev(). Oops.
- *
- * v0.12c -> v0.13beta1 - 13 Sep 2002 - David Gibson
- * o Revert the broken 0.12* locking scheme and go to a new yet
- * simpler scheme.
- * o Do firmware resets only in orinoco_init() and when waking
- * the card from hard sleep.
- *
- * v0.13beta1 -> v0.13 - 27 Sep 2002 - David Gibson
- * o Re-introduced full resets (via schedule_task()) on Tx
- * timeout.
- *
- * v0.13 -> v0.13a - 30 Sep 2002 - David Gibson
- * o Minor cleanups to info frame handling. Add basic support
- * for linkstatus info frames.
- * o Include required kernel headers in orinoco.h, to avoid
- * compile problems.
- *
- * v0.13a -> v0.13b - 10 Feb 2003 - David Gibson
- * o Implemented hard reset for Airport cards
- * o Experimental suspend/resume implementation for orinoco_pci
- * o Abolished /proc debugging support, replaced with a debugging
- * iwpriv. Now it's ugly and simple instead of ugly and complex.
- * o Bugfix in hermes.c if the firmware returned a record length
- * of 0, we could go clobbering memory.
- * o Bugfix in orinoco_stop() - it used to fail if hw_unavailable
- * was set, which was usually true on PCMCIA hot removes.
- * o Track LINKSTATUS messages, silently drop Tx packets before
- * we are connected (avoids confusing the firmware), and only
- * give LINKSTATUS printk()s if the status has changed.
- *
- * v0.13b -> v0.13c - 11 Mar 2003 - David Gibson
- * o Cleanup: use dev instead of priv in various places.
- * o Bug fix: Don't ReleaseConfiguration on RESET_PHYSICAL event
- * if we're in the middle of a (driver initiated) hard reset.
- * o Bug fix: ETH_ZLEN is supposed to include the header
- * (Dionysus Blazakis & Manish Karir)
- * o Convert to using workqueues instead of taskqueues (and
- * backwards compatibility macros for pre 2.5.41 kernels).
- * o Drop redundant (I think...) MOD_{INC,DEC}_USE_COUNT in
- * airport.c
- * o New orinoco_tmd.c init module from Joerg Dorchain for
- * TMD7160 based PCI to PCMCIA bridges (similar to
- * orinoco_plx.c).
- *
- * v0.13c -> v0.13d - 22 Apr 2003 - David Gibson
- * o Make hw_unavailable a counter, rather than just a flag, this
- * is necessary to avoid some races (such as a card being
- * removed in the middle of orinoco_reset().
- * o Restore Release/RequestConfiguration in the PCMCIA event handler
- * when dealing with a driver initiated hard reset. This is
- * necessary to prevent hangs due to a spurious interrupt while
- * the reset is in progress.
- * o Clear the 802.11 header when transmitting, even though we
- * don't use it. This fixes a long standing bug on some
- * firmwares, which seem to get confused if that isn't done.
- * o Be less eager to de-encapsulate SNAP frames, only do so if
- * the OUI is 00:00:00 or 00:00:f8, leave others alone. The old
- * behaviour broke CDP (Cisco Discovery Protocol).
- * o Use dev instead of priv for free_irq() as well as
- * request_irq() (oops).
- * o Attempt to reset rather than giving up if we get too many
- * IRQs.
- * o Changed semantics of __orinoco_down() so it can be called
- * safely with hw_unavailable set. It also now clears the
- * linkstatus (since we're going to have to reassociate).
- *
- * v0.13d -> v0.13e - 12 May 2003 - David Gibson
- * o Support for post-2.5.68 return values from irq handler.
- * o Fixed bug where underlength packets would be double counted
- * in the rx_dropped statistics.
- * o Provided a module parameter to suppress linkstatus messages.
- *
- * v0.13e -> v0.14alpha1 - 30 Sep 2003 - David Gibson
- * o Replaced priv->connected logic with netif_carrier_on/off()
- * calls.
- * o Remove has_ibss_any and never set the CREATEIBSS RID when
- * the ESSID is empty. Too many firmwares break if we do.
- * o 2.6 merges: Replace pdev->slot_name with pci_name(), remove
- * __devinitdata from PCI ID tables, use free_netdev().
- * o Enabled shared-key authentication for Agere firmware (from
- * Robert J. Moore <Robert.J.Moore AT allanbank.com>
- * o Move netif_wake_queue() (back) to the Tx completion from the
- * ALLOC event. This seems to prevent/mitigate the rolling
- * error -110 problems at least on some Intersil firmwares.
- * Theoretically reduces performance, but I can't measure it.
- * Patch from Andrew Tridgell <tridge AT samba.org>
- *
- * v0.14alpha1 -> v0.14alpha2 - 20 Oct 2003 - David Gibson
- * o Correctly turn off shared-key authentication when requested
- * (bugfix from Robert J. Moore).
- * o Correct airport sleep interfaces for current 2.6 kernels.
- * o Add code for key change without disabling/enabling the MAC
- * port. This is supposed to allow 802.1x to work sanely, but
- * doesn't seem to yet.
- *
- * v0.14alpha2 -> v0.15rc1 - 19 Apr 2004 - Pavel Roskin & David Gibson
- * o Fix bug which prevented setting 32 character ESSIDs from
- * iwconfig (Thomas Schulz).
- * o Fix for incorrect CIS access in orinoco_plx (Pavel Roskin).
- * o Fix setting WEP key if __orinoco_fastkeychange() is not
- * supported (Pavel Roskin).
- * o New wireless extensions API and scanning support (patch from
- * Moustafa Youssef, updated by Jim Carter and Pavel Roskin).
- * o Add minimal ethtool support (Pavel Roskin).
- * o Replace CardServices() calls for compatibility with Linux
- * 2.6.2 and above (Pavel Roskin).
- * o Fix recognition of Intersil x.x.1 firmware (Pavel Roskin).
- * o Replace dump_recs with more flexible get_rid ioctl (Pavel
- * Roskin).
- * o RF monitor mode support (Pavel Roskin).
- * o Lots of bugfixes.
- *
- * v0.15rc1 -> v0.15rc2 - 28 Jul 2004 - Pavel Roskin & David Gibson
- * o orinoco_pci saves PCI registers on suspend (Simon Huggins).
- * o Monitor mode disabled on Agere 8.xx firmware - it's broken.
- * o BAP timeout increased - needed for Intersil firmware.
- * o Tx power is no longer reported - it's unreliable.
- * o Use 802.11 header in rx path. Hide packets with ToDS flag
- * from programs that don't need promiscous mode (John Denker).
- * o Manual roaming implemented for Symbol and Intersil firmware.
- * o Use netdev_priv() instead of directly dereferencing dev->priv.
- * o Some simplification of pcmcia init code in orinoco_cs and
- * spectrum_cs.
- * o Numerous trivial cleanups, mainly arising from long-overdue
- * merge with mainline.
- *
- * v0.15rc2 -> ???? - ???? - David Gibson
- * o Use ssleep() or msleep() instead of hardcoded
- * schedule_timeout()s (Nishanth Aravamudan via kernel-janitors
- * list).
- * o Several cleanups and bugfixes in pci/plx/tmd/nortel drivers.
- * o Fix memory leak in orinoco_join_ap().
- * o Change io handling to avoid sparse and gcc warnings.
- * o Use C99 array initializers and ARRAY_SIZE() for iw_handler
- * tables.
- *
* TODO
* o Handle de-encapsulation within network layer, provide 802.11
* headers (patch from Thomas 'Dent' Mirlacher)
#define DRIVER_NAME "orinoco"
#include <linux/config.h>
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/ptrace.h>
-#include <linux/slab.h>
-#include <linux/string.h>
-#include <linux/timer.h>
-#include <linux/ioport.h>
#include <linux/netdevice.h>
-#include <linux/if_arp.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/wireless.h>
#include <net/iw_handler.h>
#include <net/ieee80211.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
-#include <asm/system.h>
-
-#include "hermes.h"
#include "hermes_rid.h"
#include "orinoco.h"
-#include "ieee802_11.h"
/********************************************************************/
/* Module information */
/* We do this this way to avoid ifdefs in the actual code */
#ifdef WIRELESS_SPY
-#define SPY_NUMBER(priv) (priv->spy_number)
+#define SPY_NUMBER(priv) (priv->spy_data.spy_number)
#else
#define SPY_NUMBER(priv) 0
#endif /* WIRELESS_SPY */
#define ENCAPS_OVERHEAD (sizeof(encaps_hdr) + 2)
#define ORINOCO_MIN_MTU 256
-#define ORINOCO_MAX_MTU (IEEE802_11_DATA_LEN - ENCAPS_OVERHEAD)
+#define ORINOCO_MAX_MTU (IEEE80211_DATA_LEN - ENCAPS_OVERHEAD)
#define SYMBOL_MAX_VER_LEN (14)
#define USER_BAP 0
/********************************************************************/
/* Used in Event handling.
- * We avoid nested structres as they break on ARM -- Moustafa */
+ * We avoid nested structures as they break on ARM -- Moustafa */
struct hermes_tx_descriptor_802_11 {
/* hermes_tx_descriptor */
- u16 status;
- u16 reserved1;
- u16 reserved2;
- u32 sw_support;
+ __le16 status;
+ __le16 reserved1;
+ __le16 reserved2;
+ __le32 sw_support;
u8 retry_count;
u8 tx_rate;
- u16 tx_control;
+ __le16 tx_control;
- /* ieee802_11_hdr */
- u16 frame_ctl;
- u16 duration_id;
+ /* ieee80211_hdr */
+ __le16 frame_ctl;
+ __le16 duration_id;
u8 addr1[ETH_ALEN];
u8 addr2[ETH_ALEN];
u8 addr3[ETH_ALEN];
- u16 seq_ctl;
+ __le16 seq_ctl;
u8 addr4[ETH_ALEN];
- u16 data_len;
+
+ __le16 data_len;
/* ethhdr */
- unsigned char h_dest[ETH_ALEN]; /* destination eth addr */
- unsigned char h_source[ETH_ALEN]; /* source ether addr */
- unsigned short h_proto; /* packet type ID field */
+ u8 h_dest[ETH_ALEN]; /* destination eth addr */
+ u8 h_source[ETH_ALEN]; /* source ether addr */
+ __be16 h_proto; /* packet type ID field */
/* p8022_hdr */
u8 dsap;
u8 ctrl;
u8 oui[3];
- u16 ethertype;
+ __be16 ethertype;
} __attribute__ ((packed));
/* Rx frame header except compatibility 802.3 header */
struct hermes_rx_descriptor {
/* Control */
- u16 status;
- u32 time;
+ __le16 status;
+ __le32 time;
u8 silence;
u8 signal;
u8 rate;
u8 rxflow;
- u32 reserved;
+ __le32 reserved;
/* 802.11 header */
- u16 frame_ctl;
- u16 duration_id;
+ __le16 frame_ctl;
+ __le16 duration_id;
u8 addr1[ETH_ALEN];
u8 addr2[ETH_ALEN];
u8 addr3[ETH_ALEN];
- u16 seq_ctl;
+ __le16 seq_ctl;
u8 addr4[ETH_ALEN];
/* Data length */
- u16 data_len;
+ __le16 data_len;
} __attribute__ ((packed));
/********************************************************************/
/* If a spy address is defined, we report stats of the
* first spy address - Jean II */
if (SPY_NUMBER(priv)) {
- wstats->qual.qual = priv->spy_stat[0].qual;
- wstats->qual.level = priv->spy_stat[0].level;
- wstats->qual.noise = priv->spy_stat[0].noise;
- wstats->qual.updated = priv->spy_stat[0].updated;
+ wstats->qual.qual = priv->spy_data.spy_stat[0].qual;
+ wstats->qual.level = priv->spy_data.spy_stat[0].level;
+ wstats->qual.noise = priv->spy_data.spy_stat[0].noise;
+ wstats->qual.updated = priv->spy_data.spy_stat[0].updated;
}
} else {
struct {
- u16 qual, signal, noise;
+ __le16 qual, signal, noise, unused;
} __attribute__ ((packed)) cq;
err = HERMES_READ_RECORD(hw, USER_BAP,
if ( (new_mtu < ORINOCO_MIN_MTU) || (new_mtu > ORINOCO_MAX_MTU) )
return -EINVAL;
- if ( (new_mtu + ENCAPS_OVERHEAD + IEEE802_11_HLEN) >
+ if ( (new_mtu + ENCAPS_OVERHEAD + IEEE80211_HLEN) >
(priv->nicbuf_size - ETH_HLEN) )
return -EINVAL;
/* Length of the packet body */
/* FIXME: what if the skb is smaller than this? */
- len = max_t(int,skb->len - ETH_HLEN, ETH_ZLEN - ETH_HLEN);
+ len = max_t(int, ALIGN(skb->len, 2), ETH_ZLEN);
+ skb = skb_padto(skb, len);
+ if (skb == NULL)
+ goto fail;
+ len -= ETH_HLEN;
eh = (struct ethhdr *)skb->data;
stats->tx_errors++;
goto fail;
}
+ /* Actual xfer length - allow for padding */
+ len = ALIGN(data_len, 2);
+ if (len < ETH_ZLEN - ETH_HLEN)
+ len = ETH_ZLEN - ETH_HLEN;
} else { /* IEEE 802.3 frame */
data_len = len + ETH_HLEN;
data_off = HERMES_802_3_OFFSET;
p = skb->data;
+ /* Actual xfer length - round up for odd length packets */
+ len = ALIGN(data_len, 2);
+ if (len < ETH_ZLEN)
+ len = ETH_ZLEN;
}
- /* Round up for odd length packets */
- err = hermes_bap_pwrite(hw, USER_BAP, p, ALIGN(data_len, 2),
+ err = hermes_bap_pwrite_pad(hw, USER_BAP, p, data_len, len,
txfid, data_off);
if (err) {
printk(KERN_ERR "%s: Error %d writing packet to BAP\n",
txfid, NULL);
if (err) {
netif_start_queue(dev);
- printk(KERN_ERR "%s: Error %d transmitting packet\n",
- dev->name, err);
+ if (net_ratelimit())
+ printk(KERN_ERR "%s: Error %d transmitting packet\n",
+ dev->name, err);
stats->tx_errors++;
goto fail;
}
struct orinoco_private *priv = netdev_priv(dev);
struct net_device_stats *stats = &priv->stats;
u16 fid = hermes_read_regn(hw, TXCOMPLFID);
+ u16 status;
struct hermes_tx_descriptor_802_11 hdr;
int err = 0;
if (fid == DUMMY_FID)
return; /* Nothing's really happened */
- /* Read the frame header */
+ /* Read part of the frame header - we need status and addr1 */
err = hermes_bap_pread(hw, IRQ_BAP, &hdr,
- sizeof(struct hermes_tx_descriptor) +
- sizeof(struct ieee80211_hdr),
+ offsetof(struct hermes_tx_descriptor_802_11,
+ addr2),
fid, 0);
hermes_write_regn(hw, TXCOMPLFID, DUMMY_FID);
* exceeded, because that's the only status that really mean
* that this particular node went away.
* Other errors means that *we* screwed up. - Jean II */
- hdr.status = le16_to_cpu(hdr.status);
- if (hdr.status & (HERMES_TXSTAT_RETRYERR | HERMES_TXSTAT_AGEDERR)) {
+ status = le16_to_cpu(hdr.status);
+ if (status & (HERMES_TXSTAT_RETRYERR | HERMES_TXSTAT_AGEDERR)) {
union iwreq_data wrqu;
/* Copy 802.11 dest address.
static inline void orinoco_spy_gather(struct net_device *dev, u_char *mac,
int level, int noise)
{
- struct orinoco_private *priv = netdev_priv(dev);
- int i;
-
- /* Gather wireless spy statistics: for each packet, compare the
- * source address with out list, and if match, get the stats... */
- for (i = 0; i < priv->spy_number; i++)
- if (!memcmp(mac, priv->spy_address[i], ETH_ALEN)) {
- priv->spy_stat[i].level = level - 0x95;
- priv->spy_stat[i].noise = noise - 0x95;
- priv->spy_stat[i].qual = (level > noise) ? (level - noise) : 0;
- priv->spy_stat[i].updated = 7;
- }
+ struct iw_quality wstats;
+ wstats.level = level - 0x95;
+ wstats.noise = noise - 0x95;
+ wstats.qual = (level > noise) ? (level - noise) : 0;
+ wstats.updated = 7;
+ /* Update spy records */
+ wireless_spy_update(dev, mac, &wstats);
}
static void orinoco_stat_gather(struct net_device *dev,
if (datalen > IEEE80211_DATA_LEN + 12) {
printk(KERN_DEBUG "%s: oversized monitor frame, "
"data length = %d\n", dev->name, datalen);
- err = -EIO;
stats->rx_length_errors++;
goto update_stats;
}
if (!skb) {
printk(KERN_WARNING "%s: Cannot allocate skb for monitor frame\n",
dev->name);
- err = -ENOMEM;
- goto drop;
+ goto update_stats;
}
/* Copy the 802.11 header to the skb */
data. */
return;
}
- if (length > IEEE802_11_DATA_LEN) {
+ if (length > IEEE80211_DATA_LEN) {
printk(KERN_WARNING "%s: Oversized frame received (%d bytes)\n",
dev->name, length);
stats->rx_length_errors++;
unsigned long flags;
struct join_req {
u8 bssid[ETH_ALEN];
- u16 channel;
+ __le16 channel;
} __attribute__ ((packed)) req;
const int atom_len = offsetof(struct prism2_scan_apinfo, atim);
- struct prism2_scan_apinfo *atom;
+ struct prism2_scan_apinfo *atom = NULL;
int offset = 4;
+ int found = 0;
u8 *buf;
u16 len;
return;
if (orinoco_lock(priv, &flags) != 0)
- goto out;
+ goto fail_lock;
/* Sanity checks in case user changed something in the meantime */
if (! priv->bssid_fixed)
* we were requested to join */
for (; offset + atom_len <= len; offset += atom_len) {
atom = (struct prism2_scan_apinfo *) (buf + offset);
- if (memcmp(&atom->bssid, priv->desired_bssid, ETH_ALEN) == 0)
- goto found;
+ if (memcmp(&atom->bssid, priv->desired_bssid, ETH_ALEN) == 0) {
+ found = 1;
+ break;
+ }
}
- DEBUG(1, "%s: Requested AP not found in scan results\n",
- dev->name);
- goto out;
+ if (! found) {
+ DEBUG(1, "%s: Requested AP not found in scan results\n",
+ dev->name);
+ goto out;
+ }
- found:
memcpy(req.bssid, priv->desired_bssid, ETH_ALEN);
req.channel = atom->channel; /* both are little-endian */
err = HERMES_WRITE_RECORD(hw, USER_BAP, HERMES_RID_CNFJOINREQUEST,
printk(KERN_ERR "%s: Error issuing join request\n", dev->name);
out:
- kfree(buf);
orinoco_unlock(priv, &flags);
+
+ fail_lock:
+ kfree(buf);
}
/* Send new BSSID to userspace */
err = hermes_read_ltv(hw, IRQ_BAP, HERMES_RID_CURRENTBSSID,
ETH_ALEN, NULL, wrqu.ap_addr.sa_data);
if (err != 0)
- return;
+ goto out;
wrqu.ap_addr.sa_family = ARPHRD_ETHER;
/* Send event to user space */
wireless_send_event(dev, SIOCGIWAP, &wrqu, NULL);
+
+ out:
orinoco_unlock(priv, &flags);
}
struct orinoco_private *priv = netdev_priv(dev);
u16 infofid;
struct {
- u16 len;
- u16 type;
+ __le16 len;
+ __le16 type;
} __attribute__ ((packed)) info;
int len, type;
int err;
/* Read scan data */
err = hermes_bap_pread(hw, IRQ_BAP, (void *) buf, len,
infofid, sizeof(info));
- if (err)
+ if (err) {
+ kfree(buf);
break;
+ }
#ifdef ORINOCO_DEBUG
{
/* Set promiscuity / multicast*/
priv->promiscuous = 0;
priv->mc_count = 0;
- __orinoco_set_multicast_list(dev); /* FIXME: what about the xmit_lock */
+
+ /* FIXME: what about netif_tx_lock */
+ __orinoco_set_multicast_list(dev);
return 0;
}
/* No need to lock, the hw_unavailable flag is already set in
* alloc_orinocodev() */
- priv->nicbuf_size = IEEE802_11_FRAME_LEN + ETH_HLEN;
+ priv->nicbuf_size = IEEE80211_FRAME_LEN + ETH_HLEN;
/* Initialize the firmware */
err = orinoco_reinit_firmware(dev);
dev->watchdog_timeo = HZ; /* 1 second timeout */
dev->get_stats = orinoco_get_stats;
dev->ethtool_ops = &orinoco_ethtool_ops;
- dev->get_wireless_stats = orinoco_get_wireless_stats;
dev->wireless_handlers = (struct iw_handler_def *)&orinoco_handler_def;
+#ifdef WIRELESS_SPY
+ priv->wireless_data.spy_data = &priv->spy_data;
+ dev->wireless_data = &priv->wireless_data;
+#endif
dev->change_mtu = orinoco_change_mtu;
dev->set_multicast_list = orinoco_set_multicast_list;
/* we use the default eth_mac_addr for setting the MAC addr */
}
}
- if ((priv->iw_mode == IW_MODE_ADHOC) && (priv->spy_number == 0)){
+ if ((priv->iw_mode == IW_MODE_ADHOC) && (!SPY_NUMBER(priv))){
/* Quality stats meaningless in ad-hoc mode */
} else {
range->max_qual.qual = 0x8b - 0x2f;
range->min_r_time = 0;
range->max_r_time = 65535 * 1000; /* ??? */
+ /* Event capability (kernel) */
+ IW_EVENT_CAPA_SET_KERNEL(range->event_capa);
+ /* Event capability (driver) */
+ IW_EVENT_CAPA_SET(range->event_capa, SIOCGIWTHRSPY);
+ IW_EVENT_CAPA_SET(range->event_capa, SIOCGIWAP);
+ IW_EVENT_CAPA_SET(range->event_capa, SIOCGIWSCAN);
+ IW_EVENT_CAPA_SET(range->event_capa, IWEVTXDROP);
+
TRACE_EXIT(dev->name);
return 0;
break;
default:
err = -EINVAL;
- }
- if (err)
goto out;
+ }
if (prq->flags & IW_POWER_TIMEOUT) {
priv->pm_on = 1;
return err;
}
-/* Spy is used for link quality/strength measurements in Ad-Hoc mode
- * Jean II */
-static int orinoco_ioctl_setspy(struct net_device *dev,
- struct iw_request_info *info,
- struct iw_point *srq,
- char *extra)
-
-{
- struct orinoco_private *priv = netdev_priv(dev);
- struct sockaddr *address = (struct sockaddr *) extra;
- int number = srq->length;
- int i;
- unsigned long flags;
-
- /* Make sure nobody mess with the structure while we do */
- if (orinoco_lock(priv, &flags) != 0)
- return -EBUSY;
-
- /* orinoco_lock() doesn't disable interrupts, so make sure the
- * interrupt rx path don't get confused while we copy */
- priv->spy_number = 0;
-
- if (number > 0) {
- /* Extract the addresses */
- for (i = 0; i < number; i++)
- memcpy(priv->spy_address[i], address[i].sa_data,
- ETH_ALEN);
- /* Reset stats */
- memset(priv->spy_stat, 0,
- sizeof(struct iw_quality) * IW_MAX_SPY);
- /* Set number of addresses */
- priv->spy_number = number;
- }
-
- /* Now, let the others play */
- orinoco_unlock(priv, &flags);
-
- /* Do NOT call commit handler */
- return 0;
-}
-
-static int orinoco_ioctl_getspy(struct net_device *dev,
- struct iw_request_info *info,
- struct iw_point *srq,
- char *extra)
-{
- struct orinoco_private *priv = netdev_priv(dev);
- struct sockaddr *address = (struct sockaddr *) extra;
- int number;
- int i;
- unsigned long flags;
-
- if (orinoco_lock(priv, &flags) != 0)
- return -EBUSY;
-
- number = priv->spy_number;
- /* Create address struct */
- for (i = 0; i < number; i++) {
- memcpy(address[i].sa_data, priv->spy_address[i], ETH_ALEN);
- address[i].sa_family = AF_UNIX;
- }
- if (number > 0) {
- /* Create address struct */
- for (i = 0; i < number; i++) {
- memcpy(address[i].sa_data, priv->spy_address[i],
- ETH_ALEN);
- address[i].sa_family = AF_UNIX;
- }
- /* Copy stats */
- /* In theory, we should disable irqs while copying the stats
- * because the rx path might update it in the middle...
- * Bah, who care ? - Jean II */
- memcpy(extra + (sizeof(struct sockaddr) * number),
- priv->spy_stat, sizeof(struct iw_quality) * number);
- }
- /* Reset updated flags. */
- for (i = 0; i < number; i++)
- priv->spy_stat[i].updated = 0;
-
- orinoco_unlock(priv, &flags);
-
- srq->length = number;
-
- return 0;
-}
-
/* Trigger a scan (look for other cells in the vicinity */
static int orinoco_ioctl_setscan(struct net_device *dev,
struct iw_request_info *info,
unsigned long flags;
/* Note : you may have realised that, as this is a SET operation,
- * this is priviledged and therefore a normal user can't
+ * this is privileged and therefore a normal user can't
* perform scanning.
* This is not an error, while the device perform scanning,
* traffic doesn't flow, so it's a perfect DoS...
HERMES_HOSTSCAN_SYMBOL_BCAST);
break;
case FIRMWARE_TYPE_INTERSIL: {
- u16 req[3];
+ __le16 req[3];
req[0] = cpu_to_le16(0x3fff); /* All channels */
req[1] = cpu_to_le16(0x0001); /* rate 1 Mbps */
}
/* Translate scan data returned from the card to a card independant
- * format that the Wireless Tools will understand - Jean II */
+ * format that the Wireless Tools will understand - Jean II
+ * Return message length or -errno for fatal errors */
static inline int orinoco_translate_scan(struct net_device *dev,
char *buffer,
char *scan,
break;
case FIRMWARE_TYPE_INTERSIL:
offset = 4;
- if (priv->has_hostscan)
- atom_len = scan[0] + (scan[1] << 8);
- else
+ if (priv->has_hostscan) {
+ atom_len = le16_to_cpup((__le16 *)scan);
+ /* Sanity check for atom_len */
+ if (atom_len < sizeof(struct prism2_scan_apinfo)) {
+ printk(KERN_ERR "%s: Invalid atom_len in scan data: %d\n",
+ dev->name, atom_len);
+ return -EIO;
+ }
+ } else
atom_len = offsetof(struct prism2_scan_apinfo, atim);
break;
default:
- return 0;
+ return -EOPNOTSUPP;
}
/* Check that we got an whole number of atoms */
printk(KERN_ERR "%s: Unexpected scan data length %d, "
"atom_len %d, offset %d\n", dev->name, scan_len,
atom_len, offset);
- return 0;
+ return -EIO;
}
/* Read the entries one by one */
/* We have some results to push back to user space */
/* Translate to WE format */
- srq->length = orinoco_translate_scan(dev, extra,
- priv->scan_result,
- priv->scan_len);
+ int ret = orinoco_translate_scan(dev, extra,
+ priv->scan_result,
+ priv->scan_len);
+
+ if (ret < 0) {
+ err = ret;
+ kfree(priv->scan_result);
+ priv->scan_result = NULL;
+ } else {
+ srq->length = ret;
- /* Return flags */
- srq->flags = (__u16) priv->scan_mode;
+ /* Return flags */
+ srq->flags = (__u16) priv->scan_mode;
- /* Results are here, so scan no longer in progress */
- priv->scan_inprogress = 0;
-
- /* In any case, Scan results will be cleaned up in the
- * reset function and when exiting the driver.
- * The person triggering the scanning may never come to
- * pick the results, so we need to do it in those places.
- * Jean II */
+ /* In any case, Scan results will be cleaned up in the
+ * reset function and when exiting the driver.
+ * The person triggering the scanning may never come to
+ * pick the results, so we need to do it in those places.
+ * Jean II */
#ifdef SCAN_SINGLE_READ
- /* If you enable this option, only one client (the first
- * one) will be able to read the result (and only one
- * time). If there is multiple concurent clients that
- * want to read scan results, this behavior is not
- * advisable - Jean II */
- kfree(priv->scan_result);
- priv->scan_result = NULL;
+ /* If you enable this option, only one client (the first
+ * one) will be able to read the result (and only one
+ * time). If there is multiple concurent clients that
+ * want to read scan results, this behavior is not
+ * advisable - Jean II */
+ kfree(priv->scan_result);
+ priv->scan_result = NULL;
#endif /* SCAN_SINGLE_READ */
- /* Here, if too much time has elapsed since last scan,
- * we may want to clean up scan results... - Jean II */
+ /* Here, if too much time has elapsed since last scan,
+ * we may want to clean up scan results... - Jean II */
+ }
+
+ /* Scan is no longer in progress */
+ priv->scan_inprogress = 0;
}
orinoco_unlock(priv, &flags);
*/
static const iw_handler orinoco_handler[] = {
- [SIOCSIWCOMMIT-SIOCIWFIRST] (iw_handler) orinoco_ioctl_commit,
- [SIOCGIWNAME -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getname,
- [SIOCSIWFREQ -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setfreq,
- [SIOCGIWFREQ -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getfreq,
- [SIOCSIWMODE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setmode,
- [SIOCGIWMODE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getmode,
- [SIOCSIWSENS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setsens,
- [SIOCGIWSENS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getsens,
- [SIOCGIWRANGE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getiwrange,
- [SIOCSIWSPY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setspy,
- [SIOCGIWSPY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getspy,
- [SIOCSIWAP -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setwap,
- [SIOCGIWAP -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getwap,
- [SIOCSIWSCAN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setscan,
- [SIOCGIWSCAN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getscan,
- [SIOCSIWESSID -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setessid,
- [SIOCGIWESSID -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getessid,
- [SIOCSIWNICKN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setnick,
- [SIOCGIWNICKN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getnick,
- [SIOCSIWRATE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setrate,
- [SIOCGIWRATE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getrate,
- [SIOCSIWRTS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setrts,
- [SIOCGIWRTS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getrts,
- [SIOCSIWFRAG -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setfrag,
- [SIOCGIWFRAG -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getfrag,
- [SIOCGIWRETRY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getretry,
- [SIOCSIWENCODE-SIOCIWFIRST] (iw_handler) orinoco_ioctl_setiwencode,
- [SIOCGIWENCODE-SIOCIWFIRST] (iw_handler) orinoco_ioctl_getiwencode,
- [SIOCSIWPOWER -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setpower,
- [SIOCGIWPOWER -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getpower,
+ [SIOCSIWCOMMIT-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_commit,
+ [SIOCGIWNAME -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getname,
+ [SIOCSIWFREQ -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setfreq,
+ [SIOCGIWFREQ -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getfreq,
+ [SIOCSIWMODE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setmode,
+ [SIOCGIWMODE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getmode,
+ [SIOCSIWSENS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setsens,
+ [SIOCGIWSENS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getsens,
+ [SIOCGIWRANGE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getiwrange,
+ [SIOCSIWSPY -SIOCIWFIRST] = (iw_handler) iw_handler_set_spy,
+ [SIOCGIWSPY -SIOCIWFIRST] = (iw_handler) iw_handler_get_spy,
+ [SIOCSIWTHRSPY-SIOCIWFIRST] = (iw_handler) iw_handler_set_thrspy,
+ [SIOCGIWTHRSPY-SIOCIWFIRST] = (iw_handler) iw_handler_get_thrspy,
+ [SIOCSIWAP -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setwap,
+ [SIOCGIWAP -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getwap,
+ [SIOCSIWSCAN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setscan,
+ [SIOCGIWSCAN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getscan,
+ [SIOCSIWESSID -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setessid,
+ [SIOCGIWESSID -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getessid,
+ [SIOCSIWNICKN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setnick,
+ [SIOCGIWNICKN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getnick,
+ [SIOCSIWRATE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setrate,
+ [SIOCGIWRATE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getrate,
+ [SIOCSIWRTS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setrts,
+ [SIOCGIWRTS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getrts,
+ [SIOCSIWFRAG -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setfrag,
+ [SIOCGIWFRAG -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getfrag,
+ [SIOCGIWRETRY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getretry,
+ [SIOCSIWENCODE-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setiwencode,
+ [SIOCGIWENCODE-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getiwencode,
+ [SIOCSIWPOWER -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setpower,
+ [SIOCGIWPOWER -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getpower,
};
Added typecasting since we no longer use iwreq_data -- Moustafa
*/
static const iw_handler orinoco_private_handler[] = {
- [0] (iw_handler) orinoco_ioctl_reset,
- [1] (iw_handler) orinoco_ioctl_reset,
- [2] (iw_handler) orinoco_ioctl_setport3,
- [3] (iw_handler) orinoco_ioctl_getport3,
- [4] (iw_handler) orinoco_ioctl_setpreamble,
- [5] (iw_handler) orinoco_ioctl_getpreamble,
- [6] (iw_handler) orinoco_ioctl_setibssport,
- [7] (iw_handler) orinoco_ioctl_getibssport,
- [9] (iw_handler) orinoco_ioctl_getrid,
+ [0] = (iw_handler) orinoco_ioctl_reset,
+ [1] = (iw_handler) orinoco_ioctl_reset,
+ [2] = (iw_handler) orinoco_ioctl_setport3,
+ [3] = (iw_handler) orinoco_ioctl_getport3,
+ [4] = (iw_handler) orinoco_ioctl_setpreamble,
+ [5] = (iw_handler) orinoco_ioctl_getpreamble,
+ [6] = (iw_handler) orinoco_ioctl_setibssport,
+ [7] = (iw_handler) orinoco_ioctl_getibssport,
+ [9] = (iw_handler) orinoco_ioctl_getrid,
};
static const struct iw_handler_def orinoco_handler_def = {
.standard = orinoco_handler,
.private = orinoco_private_handler,
.private_args = orinoco_privtab,
+ .get_wireless_stats = orinoco_get_wireless_stats,
};
static void orinoco_get_drvinfo(struct net_device *dev,
git://git.onelab.eu / linux-2.6.git / blobdiff