fedora core 6 1.2949 + vserver 2.2.0

[linux-2.6.git] / drivers / net / wireless / prism54 / islpci_dev.c

diff --git a/drivers/net/wireless/prism54/islpci_dev.c b/drivers/net/wireless/prism54/islpci_dev.c
index 5ddf295..f057fd9 100644 (file)
--- a/drivers/net/wireless/prism54/islpci_dev.c
+++ b/drivers/net/wireless/prism54/islpci_dev.c
@@ -1,5 +1,4 @@
 /*
- *  
  *  Copyright (C) 2002 Intersil Americas Inc.
  *  Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
  *  Copyright (C) 2003 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
@@ -182,7 +181,7 @@ isl_upload_firmware(islpci_private *priv)
 ******************************************************************************/
 
 irqreturn_t
-islpci_interrupt(int irq, void *config, struct pt_regs *regs)
+islpci_interrupt(int irq, void *config)
 {
        u32 reg;
        islpci_private *priv = config;
@@ -413,7 +412,7 @@ prism54_bring_down(islpci_private *priv)
        islpci_set_state(priv, PRV_STATE_PREBOOT);
 
        /* disable all device interrupts in case they weren't */
-       isl38xx_disable_interrupts(priv->device_base);  
+       isl38xx_disable_interrupts(priv->device_base);
 
        /* For safety reasons, we may want to ensure that no DMA transfer is
         * currently in progress by emptying the TX and RX queues. */
@@ -480,7 +479,7 @@ islpci_reset_if(islpci_private *priv)
 
        DEFINE_WAIT(wait);
        prepare_to_wait(&priv->reset_done, &wait, TASK_UNINTERRUPTIBLE);
-       
+
        /* now the last step is to reset the interface */
        isl38xx_interface_reset(priv->device_base, priv->device_host_address);
        islpci_set_state(priv, PRV_STATE_PREINIT);
@@ -488,7 +487,7 @@ islpci_reset_if(islpci_private *priv)
         for(count = 0; count < 2 && result; count++) {
                /* The software reset acknowledge needs about 220 msec here.
                 * Be conservative and wait for up to one second. */
-       
+
                remaining = schedule_timeout_uninterruptible(HZ);
 
                if(remaining > 0) {
@@ -496,7 +495,7 @@ islpci_reset_if(islpci_private *priv)
                        break;
                }
 
-               /* If we're here it's because our IRQ hasn't yet gone through. 
+               /* If we're here it's because our IRQ hasn't yet gone through.
                 * Retry a bit more...
                 */
                printk(KERN_ERR "%s: no 'reset complete' IRQ seen - retrying\n",
@@ -514,7 +513,7 @@ islpci_reset_if(islpci_private *priv)
 
        /* Now that the device is 100% up, let's allow
         * for the other interrupts --
-        * NOTE: this is not *yet* true since we've only allowed the 
+        * NOTE: this is not *yet* true since we've only allowed the
         * INIT interrupt on the IRQ line. We can perhaps poll
         * the IRQ line until we know for sure the reset went through */
        isl38xx_enable_common_interrupts(priv->device_base);
@@ -715,8 +714,8 @@ islpci_alloc_memory(islpci_private *priv)
        }
 
        prism54_acl_init(&priv->acl);
-       prism54_wpa_ie_init(priv);
-       if (mgt_init(priv)) 
+       prism54_wpa_bss_ie_init(priv);
+       if (mgt_init(priv))
                goto out_free;
 
        return 0;
@@ -774,7 +773,7 @@ islpci_free_memory(islpci_private *priv)
 
        /* Free the acces control list and the WPA list */
        prism54_acl_clean(&priv->acl);
-       prism54_wpa_ie_clean(priv);
+       prism54_wpa_bss_ie_clean(priv);
        mgt_clean(priv);
 
        return 0;
@@ -861,11 +860,10 @@ islpci_setup(struct pci_dev *pdev)
        priv->state_off = 1;
 
        /* initialize workqueue's */
-       INIT_WORK(&priv->stats_work,
-                 (void (*)(void *)) prism54_update_stats, priv);
+       INIT_WORK(&priv->stats_work, prism54_update_stats);
        priv->stats_timestamp = 0;
 
-       INIT_WORK(&priv->reset_task, islpci_do_reset_and_wake, priv);
+       INIT_WORK(&priv->reset_task, islpci_do_reset_and_wake);
        priv->reset_task_pending = 0;
 
        /* allocate various memory areas */