config SCSI_AACRAID
tristate "Adaptec AACRAID support"
depends on SCSI && PCI
- help
- This driver supports a variety of Dell, HP, Adaptec, IBM and
- ICP storage products. For a list of supported products, refer
- to <file:Documentation/scsi/aacraid.txt>.
-
- To compile this driver as a module, choose M here: the module
- will be called aacraid.
-
source "drivers/scsi/aic7xxx/Kconfig.aic7xxx"
tristate "Intel PIIX/ICH SATA support"
depends on SCSI_SATA && PCI
help
- This option enables support for ICH5/6/7/8 Serial ATA.
+ This option enables support for ICH5 Serial ATA.
If PATA support was enabled previously, this enables
support for select Intel PIIX/ICH PATA host controllers.
If unsure, say N.
config SCSI_SATA_VITESSE
- tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
+ tristate "VITESSE VSC-7174 SATA support"
depends on SCSI_SATA && PCI
help
- This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
+ This option enables support for Vitesse VSC7174 Serial ATA.
If unsure, say N.
memory using PCI DAC cycles.
config SCSI_SYM53C8XX_DEFAULT_TAGS
- int "Default tagged command queue depth"
+ int "default tagged command queue depth"
depends on SCSI_SYM53C8XX_2
default "16"
help
exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.
config SCSI_SYM53C8XX_MAX_TAGS
- int "Maximum number of queued commands"
+ int "maximum number of queued commands"
depends on SCSI_SYM53C8XX_2
default "64"
help
possible. The driver supports up to 256 queued commands per device.
This value is used as a compiled-in hard limit.
-config SCSI_SYM53C8XX_MMIO
- bool "Use memory mapped IO"
+config SCSI_SYM53C8XX_IOMAPPED
+ bool "use port IO"
depends on SCSI_SYM53C8XX_2
- default y
help
- Memory mapped IO is faster than Port IO. Most people should
- answer Y here, but some machines may have problems. If you have
- to answer N here, please report the problem to the maintainer.
+ If you say Y here, the driver will use port IO to access
+ the card. This is significantly slower then using memory
+ mapped IO. Most people should answer N.
config SCSI_IPR
tristate "IBM Power Linux RAID adapter support"
you do not have this SCSI card, so say N.
config SCSI_NCR53C8XX_DEFAULT_TAGS
- int "default tagged command queue depth"
+ int " default tagged command queue depth"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "8"
---help---
There is no safe option other than using good SCSI devices.
config SCSI_NCR53C8XX_MAX_TAGS
- int "maximum number of queued commands"
+ int " maximum number of queued commands"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "32"
---help---
There is no safe option and the default answer is recommended.
config SCSI_NCR53C8XX_SYNC
- int "synchronous transfers frequency in MHz"
+ int " synchronous transfers frequency in MHz"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "20"
---help---
terminations and SCSI conformant devices.
config SCSI_NCR53C8XX_PROFILE
- bool "enable profiling"
+ bool " enable profiling"
depends on SCSI_ZALON || SCSI_NCR_Q720
help
This option allows you to enable profiling information gathering.
The normal answer therefore is N.
config SCSI_NCR53C8XX_NO_DISCONNECT
- bool "not allow targets to disconnect"
+ bool " not allow targets to disconnect"
depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
help
This option is only provided for safety if you suspect some SCSI
To compile this driver as a module, choose M here: the
module will be called qlogicfas.
+config SCSI_QLOGIC_FC
+ tristate "Qlogic ISP FC SCSI support"
+ depends on PCI && SCSI
+ help
+ This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.
+
+ To compile this driver as a module, choose M here: the
+ module will be called qlogicfc.
+
config SCSI_QLOGIC_FC_FIRMWARE
bool "Include loadable firmware in driver"
depends on SCSI_QLOGIC_FC