Merge to Fedora kernel-2.6.18-1.2224_FC5 patched with stable patch-2.6.18.1-vs2.0...

[linux-2.6.git] / drivers / serial / crisv10.c

diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c
index 8970014..cabd048 100644 (file)
--- a/drivers/serial/crisv10.c
+++ b/drivers/serial/crisv10.c
@@ -415,7 +415,7 @@
  * Fixed DEF_TX value that caused the serial transmitter pin (txd) to go to 0 when
  * closing the last filehandle, NASTY!.
  * Added break generation, not tested though!
- * Use SA_SHIRQ when request_irq() for ser2 and ser3 (shared with) par0 and par1.
+ * Use IRQF_SHARED when request_irq() for ser2 and ser3 (shared with) par0 and par1.
  * You can't use them at the same time (yet..), but you can hopefully switch
  * between ser2/par0, ser3/par1 with the same kernel config.
  * Replaced some magic constants with defines
@@ -425,7 +425,6 @@
 
 static char *serial_version = "$Revision: 1.25 $";
 
-#include <linux/config.h>
 #include <linux/types.h>
 #include <linux/errno.h>
 #include <linux/signal.h>
@@ -2573,12 +2572,6 @@ static void flush_to_flip_buffer(struct e100_serial *info)
 
        DFLIP(
          if (1) {
-
-                 if (test_bit(TTY_DONT_FLIP, &tty->flags)) {
-                         DEBUG_LOG(info->line, "*** TTY_DONT_FLIP set flip.count %i ***\n", tty->flip.count);
-                         DEBUG_LOG(info->line, "*** recv_cnt %i\n", info->recv_cnt);
-                 } else {
-                 }
                  DEBUG_LOG(info->line, "*** rxtot %i\n", info->icount.rx);
                  DEBUG_LOG(info->line, "ldisc %lu\n", tty->ldisc.chars_in_buffer(tty));
                  DEBUG_LOG(info->line, "room  %lu\n", tty->ldisc.receive_room(tty));
@@ -4884,7 +4877,7 @@ rs_init(void)
        driver->init_termios = tty_std_termios;
        driver->init_termios.c_cflag =
                B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */
-       driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_NO_DEVFS;
+       driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
        driver->termios = serial_termios;
        driver->termios_locked = serial_termios_locked;
 
@@ -4949,55 +4942,55 @@ rs_init(void)
        /* Not needed in simulator.  May only complicate stuff. */
        /* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */
 
-       if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial ", NULL))
+       if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial ", NULL))
                panic("irq8");
 
 #ifdef CONFIG_ETRAX_SERIAL_PORT0
 #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT
-       if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, SA_INTERRUPT, "serial 0 dma tr", NULL))
+       if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 0 dma tr", NULL))
                panic("irq22");
 #endif
 #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN
-       if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, SA_INTERRUPT, "serial 0 dma rec", NULL))
+       if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 0 dma rec", NULL))
                panic("irq23");
 #endif
 #endif
 
 #ifdef CONFIG_ETRAX_SERIAL_PORT1
 #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT
-       if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, SA_INTERRUPT, "serial 1 dma tr", NULL))
+       if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 1 dma tr", NULL))
                panic("irq24");
 #endif
 #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN
-       if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, SA_INTERRUPT, "serial 1 dma rec", NULL))
+       if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 1 dma rec", NULL))
                panic("irq25");
 #endif
 #endif
 #ifdef CONFIG_ETRAX_SERIAL_PORT2
        /* DMA Shared with par0 (and SCSI0 and ATA) */
 #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT
-       if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 2 dma tr", NULL))
+       if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma tr", NULL))
                panic("irq18");
 #endif
 #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN
-       if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 2 dma rec", NULL))
+       if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma rec", NULL))
                panic("irq19");
 #endif
 #endif
 #ifdef CONFIG_ETRAX_SERIAL_PORT3
        /* DMA Shared with par1 (and SCSI1 and Extern DMA 0) */
 #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT
-       if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 3 dma tr", NULL))
+       if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma tr", NULL))
                panic("irq20");
 #endif
 #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN
-       if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 3 dma rec", NULL))
+       if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma rec", NULL))
                panic("irq21");
 #endif
 #endif
 
 #ifdef CONFIG_ETRAX_SERIAL_FLUSH_DMA_FAST
-       if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, SA_SHIRQ | SA_INTERRUPT,
+       if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, IRQF_SHARED | IRQF_DISABLED,
                       "fast serial dma timeout", NULL)) {
                printk(KERN_CRIT "err: timer1 irq\n");
        }