*/
#include <linux/config.h>
-
-#ifdef CONFIG_USB_DEBUG
- #define DEBUG
-#else
- #undef DEBUG
-#endif
-
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
+#include <linux/usb.h>
+
#include <asm/io.h>
#include <asm/irq.h>
-#include <linux/usb.h>
+
+#ifdef CONFIG_PPC_PMAC
+#include <asm/machdep.h>
+#include <asm/pmac_feature.h>
+#include <asm/pci-bridge.h>
+#include <asm/prom.h>
+#endif
+
+#include "usb.h"
#include "hcd.h"
}
}
-#ifdef CONFIG_PCI_NAMES
- hcd->product_desc = dev->pretty_name;
-#endif
-
pci_set_master (dev);
retval = usb_add_hcd (hcd, dev->irq, SA_SHIRQ);
hcd = pci_get_drvdata(dev);
+ /* Root hub suspend should have stopped all downstream traffic,
+ * and all bus master traffic. And done so for both the interface
+ * and the stub usb_device (which we check here). But maybe it
+ * didn't; writing sysfs power/state files ignores such rules...
+ *
+ * We must ignore the FREEZE vs SUSPEND distinction here, because
+ * otherwise the swsusp will save (and restore) garbage state.
+ */
+ if (hcd->self.root_hub->dev.power.power_state.event == PM_EVENT_ON)
+ return -EBUSY;
+
+ if (hcd->driver->suspend) {
+ retval = hcd->driver->suspend(hcd, message);
+ suspend_report_result(hcd->driver->suspend, retval);
+ if (retval)
+ goto done;
+ }
+ synchronize_irq(dev->irq);
+
/* FIXME until the generic PM interfaces change a lot more, this
* can't use PCI D1 and D2 states. For example, the confusion
* between messages and states will need to vanish, and messages
*/
has_pci_pm = pci_find_capability(dev, PCI_CAP_ID_PM);
- switch (hcd->state) {
-
- /* entry if root hub wasn't yet suspended ... from sysfs,
- * without autosuspend, or if USB_SUSPEND isn't configured.
+ /* Downstream ports from this root hub should already be quiesced, so
+ * there will be no DMA activity. Now we can shut down the upstream
+ * link (except maybe for PME# resume signaling) and enter some PCI
+ * low power state, if the hardware allows.
*/
- case HC_STATE_RUNNING:
- hcd->state = HC_STATE_QUIESCING;
- retval = hcd->driver->suspend (hcd, message);
- if (retval) {
- dev_dbg (hcd->self.controller,
- "suspend fail, retval %d\n",
- retval);
- break;
- }
- hcd->state = HC_STATE_SUSPENDED;
- /* FALLTHROUGH */
+ if (hcd->state == HC_STATE_SUSPENDED) {
- /* entry with CONFIG_USB_SUSPEND, or hcds that autosuspend: the
- * controller and/or root hub will already have been suspended,
- * but it won't be ready for a PCI resume call.
- *
- * FIXME only CONFIG_USB_SUSPEND guarantees hub_suspend() will
- * have been called, otherwise root hub timers still run ...
- */
- case HC_STATE_SUSPENDED:
/* no DMA or IRQs except when HC is active */
if (dev->current_state == PCI_D0) {
- free_irq (hcd->irq, hcd);
pci_save_state (dev);
pci_disable_device (dev);
}
if (!has_pci_pm) {
dev_dbg (hcd->self.controller, "--> PCI D0/legacy\n");
- break;
+ goto done;
}
/* NOTE: dev->current_state becomes nonzero only here, and
* some device state (e.g. as part of clock reinit).
*/
retval = pci_set_power_state (dev, PCI_D3hot);
+ suspend_report_result(pci_set_power_state, retval);
if (retval == 0) {
- dev_dbg (hcd->self.controller, "--> PCI D3\n");
- pci_enable_wake (dev, PCI_D3hot, hcd->remote_wakeup);
- pci_enable_wake (dev, PCI_D3cold, hcd->remote_wakeup);
- } else if (retval < 0) {
+ int wake = device_can_wakeup(&hcd->self.root_hub->dev);
+
+ wake = wake && device_may_wakeup(hcd->self.controller);
+
+ dev_dbg (hcd->self.controller, "--> PCI D3%s\n",
+ wake ? "/wakeup" : "");
+
+ /* Ignore these return values. We rely on pci code to
+ * reject requests the hardware can't implement, rather
+ * than coding the same thing.
+ */
+ (void) pci_enable_wake (dev, PCI_D3hot, wake);
+ (void) pci_enable_wake (dev, PCI_D3cold, wake);
+ } else {
dev_dbg (&dev->dev, "PCI D3 suspend fail, %d\n",
retval);
(void) usb_hcd_pci_resume (dev);
- break;
}
- break;
- default:
+
+ } else {
dev_dbg (hcd->self.controller, "hcd state %d; not suspended\n",
hcd->state);
WARN_ON(1);
retval = -EINVAL;
- break;
}
- /* update power_state **ONLY** to make sysfs happier */
- if (retval == 0)
- dev->dev.power.power_state = message;
+done:
+ if (retval == 0) {
+ dev->dev.power.power_state = PMSG_SUSPEND;
+
+#ifdef CONFIG_PPC_PMAC
+ /* Disable ASIC clocks for USB */
+ if (machine_is(powermac)) {
+ struct device_node *of_node;
+
+ of_node = pci_device_to_OF_node (dev);
+ if (of_node)
+ pmac_call_feature(PMAC_FTR_USB_ENABLE,
+ of_node, 0, 0);
+ }
+#endif
+ }
+
return retval;
}
EXPORT_SYMBOL (usb_hcd_pci_suspend);
return 0;
}
+#ifdef CONFIG_PPC_PMAC
+ /* Reenable ASIC clocks for USB */
+ if (machine_is(powermac)) {
+ struct device_node *of_node;
+
+ of_node = pci_device_to_OF_node (dev);
+ if (of_node)
+ pmac_call_feature (PMAC_FTR_USB_ENABLE,
+ of_node, 0, 1);
+ }
+#endif
+
/* NOTE: chip docs cover clean "real suspend" cases (what Linux
* calls "standby", "suspend to RAM", and so on). There are also
* dirty cases when swsusp fakes a suspend in "shutdown" mode.
dev->current_state);
}
#endif
- pci_enable_wake (dev, dev->current_state, 0);
- pci_enable_wake (dev, PCI_D3cold, 0);
+ /* yes, ignore these results too... */
+ (void) pci_enable_wake (dev, dev->current_state, 0);
+ (void) pci_enable_wake (dev, PCI_D3cold, 0);
} else {
/* Same basic cases: clean (powered/not), dirty */
dev_dbg(hcd->self.controller, "PCI legacy resume\n");
dev->dev.power.power_state = PMSG_ON;
- hcd->state = HC_STATE_RESUMING;
- hcd->saw_irq = 0;
- retval = request_irq (dev->irq, usb_hcd_irq, SA_SHIRQ,
- hcd->irq_descr, hcd);
- if (retval < 0) {
- dev_err (hcd->self.controller,
- "can't restore IRQ after resume!\n");
- usb_hc_died (hcd);
- return retval;
- }
+ clear_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
- retval = hcd->driver->resume (hcd);
- if (!HC_IS_RUNNING (hcd->state)) {
- dev_dbg (hcd->self.controller,
- "resume fail, retval %d\n", retval);
- usb_hc_died (hcd);
+ if (hcd->driver->resume) {
+ retval = hcd->driver->resume(hcd);
+ if (retval) {
+ dev_err (hcd->self.controller,
+ "PCI post-resume error %d!\n", retval);
+ usb_hc_died (hcd);
+ }
}
return retval;
git://git.onelab.eu / linux-2.6.git / blobdiff