*/
#include <linux/config.h>
-
-#ifdef CONFIG_USB_DEBUG
-#define DEBUG
-#endif
-
#include <linux/module.h>
#include <linux/version.h>
#include <linux/kernel.h>
#include <asm/scatterlist.h>
#include <linux/device.h>
#include <linux/dma-mapping.h>
+#include <linux/mutex.h>
#include <asm/irq.h>
#include <asm/byteorder.h>
static struct usb_busmap busmap;
/* used when updating list of hcds */
-DECLARE_MUTEX (usb_bus_list_lock); /* exported only for usbfs */
+DEFINE_MUTEX(usb_bus_list_lock); /* exported only for usbfs */
EXPORT_SYMBOL_GPL (usb_bus_list_lock);
/* used for controlling access to virtual root hubs */
0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */
0x00, /* __u8 bDeviceSubClass; */
0x01, /* __u8 bDeviceProtocol; [ usb 2.0 single TT ]*/
- 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */
+ 0x40, /* __u8 bMaxPacketSize0; 64 Bytes */
0x00, 0x00, /* __le16 idVendor; */
0x00, 0x00, /* __le16 idProduct; */
0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */
0x00, /* __u8 bDeviceSubClass; */
0x00, /* __u8 bDeviceProtocol; [ low/full speeds only ] */
- 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */
+ 0x40, /* __u8 bMaxPacketSize0; 64 Bytes */
0x00, 0x00, /* __le16 idVendor; */
0x00, 0x00, /* __le16 idProduct; */
/* DEVICE REQUESTS */
+ /* The root hub's remote wakeup enable bit is implemented using
+ * driver model wakeup flags. If this system supports wakeup
+ * through USB, userspace may change the default "allow wakeup"
+ * policy through sysfs or these calls.
+ *
+ * Most root hubs support wakeup from downstream devices, for
+ * runtime power management (disabling USB clocks and reducing
+ * VBUS power usage). However, not all of them do so; silicon,
+ * board, and BIOS bugs here are not uncommon, so these can't
+ * be treated quite like external hubs.
+ *
+ * Likewise, not all root hubs will pass wakeup events upstream,
+ * to wake up the whole system. So don't assume root hub and
+ * controller capabilities are identical.
+ */
+
case DeviceRequest | USB_REQ_GET_STATUS:
- tbuf [0] = (hcd->remote_wakeup << USB_DEVICE_REMOTE_WAKEUP)
+ tbuf [0] = (device_may_wakeup(&hcd->self.root_hub->dev)
+ << USB_DEVICE_REMOTE_WAKEUP)
| (1 << USB_DEVICE_SELF_POWERED);
tbuf [1] = 0;
len = 2;
break;
case DeviceOutRequest | USB_REQ_CLEAR_FEATURE:
if (wValue == USB_DEVICE_REMOTE_WAKEUP)
- hcd->remote_wakeup = 0;
+ device_set_wakeup_enable(&hcd->self.root_hub->dev, 0);
else
goto error;
break;
case DeviceOutRequest | USB_REQ_SET_FEATURE:
- if (hcd->can_wakeup && wValue == USB_DEVICE_REMOTE_WAKEUP)
- hcd->remote_wakeup = 1;
+ if (device_can_wakeup(&hcd->self.root_hub->dev)
+ && wValue == USB_DEVICE_REMOTE_WAKEUP)
+ device_set_wakeup_enable(&hcd->self.root_hub->dev, 1);
else
goto error;
break;
bufp = fs_rh_config_descriptor;
len = sizeof fs_rh_config_descriptor;
}
- if (hcd->can_wakeup)
+ if (device_can_wakeup(&hcd->self.root_hub->dev))
patch_wakeup = 1;
break;
case USB_DT_STRING << 8:
default:
/* non-generic request */
- if (HC_IS_SUSPENDED (hcd->state))
- status = -EAGAIN;
- else {
- switch (typeReq) {
- case GetHubStatus:
- case GetPortStatus:
- len = 4;
- break;
- case GetHubDescriptor:
- len = sizeof (struct usb_hub_descriptor);
- break;
- }
- status = hcd->driver->hub_control (hcd,
- typeReq, wValue, wIndex,
- tbuf, wLength);
+ switch (typeReq) {
+ case GetHubStatus:
+ case GetPortStatus:
+ len = 4;
+ break;
+ case GetHubDescriptor:
+ len = sizeof (struct usb_hub_descriptor);
+ break;
}
+ status = hcd->driver->hub_control (hcd,
+ typeReq, wValue, wIndex,
+ tbuf, wLength);
break;
error:
/* "protocol stall" on error */
"CTRL: TypeReq=0x%x val=0x%x "
"idx=0x%x len=%d ==> %d\n",
typeReq, wValue, wIndex,
- wLength, urb->status);
+ wLength, status);
}
}
if (len) {
/*-------------------------------------------------------------------------*/
/*
- * Root Hub interrupt transfers are synthesized with a timer.
- * Completions are called in_interrupt() but not in_irq().
+ * Root Hub interrupt transfers are polled using a timer if the
+ * driver requests it; otherwise the driver is responsible for
+ * calling usb_hcd_poll_rh_status() when an event occurs.
*
- * Note: some root hubs (including common UHCI based designs) can't
- * correctly issue port change IRQs. They're the ones that _need_ a
- * timer; most other root hubs don't. Some systems could save a
- * lot of battery power by eliminating these root hub timer IRQs.
+ * Completions are called in_interrupt(), but they may or may not
+ * be in_irq().
*/
+void usb_hcd_poll_rh_status(struct usb_hcd *hcd)
+{
+ struct urb *urb;
+ int length;
+ unsigned long flags;
+ char buffer[4]; /* Any root hubs with > 31 ports? */
+
+ if (!hcd->uses_new_polling && !hcd->status_urb)
+ return;
-static void rh_report_status (unsigned long ptr);
+ length = hcd->driver->hub_status_data(hcd, buffer);
+ if (length > 0) {
-static int rh_status_urb (struct usb_hcd *hcd, struct urb *urb)
-{
- int len = 1 + (urb->dev->maxchild / 8);
+ /* try to complete the status urb */
+ local_irq_save (flags);
+ spin_lock(&hcd_root_hub_lock);
+ urb = hcd->status_urb;
+ if (urb) {
+ spin_lock(&urb->lock);
+ if (urb->status == -EINPROGRESS) {
+ hcd->poll_pending = 0;
+ hcd->status_urb = NULL;
+ urb->status = 0;
+ urb->hcpriv = NULL;
+ urb->actual_length = length;
+ memcpy(urb->transfer_buffer, buffer, length);
+ } else /* urb has been unlinked */
+ length = 0;
+ spin_unlock(&urb->lock);
+ } else
+ length = 0;
+ spin_unlock(&hcd_root_hub_lock);
- /* rh_timer protected by hcd_data_lock */
- if (hcd->rh_timer.data || urb->transfer_buffer_length < len) {
- dev_dbg (hcd->self.controller,
- "not queuing rh status urb, stat %d\n",
- urb->status);
- return -EINVAL;
+ /* local irqs are always blocked in completions */
+ if (length > 0)
+ usb_hcd_giveback_urb (hcd, urb, NULL);
+ else
+ hcd->poll_pending = 1;
+ local_irq_restore (flags);
}
- init_timer (&hcd->rh_timer);
- hcd->rh_timer.function = rh_report_status;
- hcd->rh_timer.data = (unsigned long) urb;
- /* USB 2.0 spec says 256msec; this is close enough */
- hcd->rh_timer.expires = jiffies + HZ/4;
- add_timer (&hcd->rh_timer);
- urb->hcpriv = hcd; /* nonzero to indicate it's queued */
- return 0;
+ /* The USB 2.0 spec says 256 ms. This is close enough and won't
+ * exceed that limit if HZ is 100. */
+ if (hcd->uses_new_polling ? hcd->poll_rh :
+ (length == 0 && hcd->status_urb != NULL))
+ mod_timer (&hcd->rh_timer, jiffies + msecs_to_jiffies(250));
}
+EXPORT_SYMBOL_GPL(usb_hcd_poll_rh_status);
/* timer callback */
+static void rh_timer_func (unsigned long _hcd)
+{
+ usb_hcd_poll_rh_status((struct usb_hcd *) _hcd);
+}
-static void rh_report_status (unsigned long ptr)
+/*-------------------------------------------------------------------------*/
+
+static int rh_queue_status (struct usb_hcd *hcd, struct urb *urb)
{
- struct urb *urb;
- struct usb_hcd *hcd;
- int length = 0;
+ int retval;
unsigned long flags;
+ int len = 1 + (urb->dev->maxchild / 8);
- urb = (struct urb *) ptr;
- local_irq_save (flags);
- spin_lock (&urb->lock);
+ spin_lock_irqsave (&hcd_root_hub_lock, flags);
+ if (urb->status != -EINPROGRESS) /* already unlinked */
+ retval = urb->status;
+ else if (hcd->status_urb || urb->transfer_buffer_length < len) {
+ dev_dbg (hcd->self.controller, "not queuing rh status urb\n");
+ retval = -EINVAL;
+ } else {
+ hcd->status_urb = urb;
+ urb->hcpriv = hcd; /* indicate it's queued */
- /* do nothing if the urb's been unlinked */
- if (!urb->dev
- || urb->status != -EINPROGRESS
- || (hcd = urb->dev->bus->hcpriv) == NULL) {
- spin_unlock (&urb->lock);
- local_irq_restore (flags);
- return;
- }
+ if (!hcd->uses_new_polling)
+ mod_timer (&hcd->rh_timer, jiffies +
+ msecs_to_jiffies(250));
- /* complete the status urb, or retrigger the timer */
- spin_lock (&hcd_data_lock);
- if (urb->dev->state == USB_STATE_CONFIGURED) {
- length = hcd->driver->hub_status_data (
- hcd, urb->transfer_buffer);
- if (length > 0) {
- hcd->rh_timer.data = 0;
- urb->actual_length = length;
- urb->status = 0;
- urb->hcpriv = NULL;
- } else
- mod_timer (&hcd->rh_timer, jiffies + HZ/4);
+ /* If a status change has already occurred, report it ASAP */
+ else if (hcd->poll_pending)
+ mod_timer (&hcd->rh_timer, jiffies);
+ retval = 0;
}
- spin_unlock (&hcd_data_lock);
- spin_unlock (&urb->lock);
-
- /* local irqs are always blocked in completions */
- if (length > 0)
- usb_hcd_giveback_urb (hcd, urb, NULL);
- local_irq_restore (flags);
+ spin_unlock_irqrestore (&hcd_root_hub_lock, flags);
+ return retval;
}
-/*-------------------------------------------------------------------------*/
-
static int rh_urb_enqueue (struct usb_hcd *hcd, struct urb *urb)
{
- if (usb_pipeint (urb->pipe)) {
- int retval;
- unsigned long flags;
-
- spin_lock_irqsave (&hcd_data_lock, flags);
- retval = rh_status_urb (hcd, urb);
- spin_unlock_irqrestore (&hcd_data_lock, flags);
- return retval;
- }
+ if (usb_pipeint (urb->pipe))
+ return rh_queue_status (hcd, urb);
if (usb_pipecontrol (urb->pipe))
return rh_call_control (hcd, urb);
- else
- return -EINVAL;
+ return -EINVAL;
}
/*-------------------------------------------------------------------------*/
+/* Asynchronous unlinks of root-hub control URBs are legal, but they
+ * don't do anything. Status URB unlinks must be made in process context
+ * with interrupts enabled.
+ */
static int usb_rh_urb_dequeue (struct usb_hcd *hcd, struct urb *urb)
{
- unsigned long flags;
-
- /* note: always a synchronous unlink */
- if ((unsigned long) urb == hcd->rh_timer.data) {
- del_timer_sync (&hcd->rh_timer);
- hcd->rh_timer.data = 0;
+ if (usb_pipeendpoint(urb->pipe) == 0) { /* Control URB */
+ if (in_interrupt())
+ return 0; /* nothing to do */
- local_irq_save (flags);
- urb->hcpriv = NULL;
- usb_hcd_giveback_urb (hcd, urb, NULL);
- local_irq_restore (flags);
-
- } else if (usb_pipeendpoint(urb->pipe) == 0) {
spin_lock_irq(&urb->lock); /* from usb_kill_urb */
++urb->reject;
spin_unlock_irq(&urb->lock);
spin_lock_irq(&urb->lock);
--urb->reject;
spin_unlock_irq(&urb->lock);
- } else
- return -EINVAL;
+
+ } else { /* Status URB */
+ if (!hcd->uses_new_polling)
+ del_timer_sync (&hcd->rh_timer);
+ local_irq_disable ();
+ spin_lock (&hcd_root_hub_lock);
+ if (urb == hcd->status_urb) {
+ hcd->status_urb = NULL;
+ urb->hcpriv = NULL;
+ } else
+ urb = NULL; /* wasn't fully queued */
+ spin_unlock (&hcd_root_hub_lock);
+ if (urb)
+ usb_hcd_giveback_urb (hcd, urb, NULL);
+ local_irq_enable ();
+ }
return 0;
}
/*-------------------------------------------------------------------------*/
/* exported only within usbcore */
-struct usb_bus *usb_bus_get (struct usb_bus *bus)
+struct usb_bus *usb_bus_get(struct usb_bus *bus)
{
- struct class_device *tmp;
+ if (bus)
+ kref_get(&bus->kref);
+ return bus;
+}
- if (!bus)
- return NULL;
+static void usb_host_release(struct kref *kref)
+{
+ struct usb_bus *bus = container_of(kref, struct usb_bus, kref);
- tmp = class_device_get(&bus->class_dev);
- if (tmp)
- return to_usb_bus(tmp);
- else
- return NULL;
+ if (bus->release)
+ bus->release(bus);
}
/* exported only within usbcore */
-void usb_bus_put (struct usb_bus *bus)
+void usb_bus_put(struct usb_bus *bus)
{
if (bus)
- class_device_put(&bus->class_dev);
+ kref_put(&bus->kref, usb_host_release);
}
/*-------------------------------------------------------------------------*/
-static void usb_host_release(struct class_device *class_dev)
-{
- struct usb_bus *bus = to_usb_bus(class_dev);
-
- if (bus->release)
- bus->release(bus);
-}
-
-static struct class usb_host_class = {
- .name = "usb_host",
- .release = &usb_host_release,
-};
+static struct class *usb_host_class;
int usb_host_init(void)
{
- return class_register(&usb_host_class);
+ int retval = 0;
+
+ usb_host_class = class_create(THIS_MODULE, "usb_host");
+ if (IS_ERR(usb_host_class))
+ retval = PTR_ERR(usb_host_class);
+ return retval;
}
void usb_host_cleanup(void)
{
- class_unregister(&usb_host_class);
+ class_destroy(usb_host_class);
}
/**
INIT_LIST_HEAD (&bus->bus_list);
- class_device_initialize(&bus->class_dev);
- bus->class_dev.class = &usb_host_class;
+ kref_init(&bus->kref);
}
/**
{
struct usb_bus *bus;
- bus = kmalloc (sizeof *bus, GFP_KERNEL);
+ bus = kzalloc (sizeof *bus, GFP_KERNEL);
if (!bus)
return NULL;
- memset(bus, 0, sizeof(struct usb_bus));
usb_bus_init (bus);
bus->op = op;
return bus;
static int usb_register_bus(struct usb_bus *bus)
{
int busnum;
- int retval;
- down (&usb_bus_list_lock);
+ mutex_lock(&usb_bus_list_lock);
busnum = find_next_zero_bit (busmap.busmap, USB_MAXBUS, 1);
if (busnum < USB_MAXBUS) {
set_bit (busnum, busmap.busmap);
bus->busnum = busnum;
} else {
printk (KERN_ERR "%s: too many buses\n", usbcore_name);
- up(&usb_bus_list_lock);
+ mutex_unlock(&usb_bus_list_lock);
return -E2BIG;
}
- snprintf(bus->class_dev.class_id, BUS_ID_SIZE, "usb%d", busnum);
- bus->class_dev.dev = bus->controller;
- retval = class_device_add(&bus->class_dev);
- if (retval) {
+ bus->class_dev = class_device_create(usb_host_class, NULL, MKDEV(0,0),
+ bus->controller, "usb_host%d", busnum);
+ if (IS_ERR(bus->class_dev)) {
clear_bit(busnum, busmap.busmap);
- up(&usb_bus_list_lock);
- return retval;
+ mutex_unlock(&usb_bus_list_lock);
+ return PTR_ERR(bus->class_dev);
}
+ class_set_devdata(bus->class_dev, bus);
+
/* Add it to the local list of buses */
list_add (&bus->bus_list, &usb_bus_list);
- up (&usb_bus_list_lock);
+ mutex_unlock(&usb_bus_list_lock);
- usbfs_add_bus (bus);
- usbmon_notify_bus_add (bus);
+ usb_notify_add_bus(bus);
dev_info (bus->controller, "new USB bus registered, assigned bus number %d\n", bus->busnum);
return 0;
* controller code, as well as having it call this when cleaning
* itself up
*/
- down (&usb_bus_list_lock);
+ mutex_lock(&usb_bus_list_lock);
list_del (&bus->bus_list);
- up (&usb_bus_list_lock);
+ mutex_unlock(&usb_bus_list_lock);
- usbmon_notify_bus_remove (bus);
- usbfs_remove_bus (bus);
+ usb_notify_remove_bus(bus);
clear_bit (bus->busnum, busmap.busmap);
- class_device_del(&bus->class_dev);
+ class_device_unregister(bus->class_dev);
}
/**
- * usb_hcd_register_root_hub - called by HCD to register its root hub
- * @usb_dev: the usb root hub device to be registered.
+ * register_root_hub - called by usb_add_hcd() to register a root hub
* @hcd: host controller for this root hub
*
- * The USB host controller calls this function to register the root hub
- * properly with the USB subsystem. It sets up the device properly in
- * the device tree and stores the root_hub pointer in the bus structure,
- * then calls usb_new_device() to register the usb device. It also
- * assigns the root hub's USB address (always 1).
+ * This function registers the root hub with the USB subsystem. It sets up
+ * the device properly in the device tree and then calls usb_new_device()
+ * to register the usb device. It also assigns the root hub's USB address
+ * (always 1).
*/
-int usb_hcd_register_root_hub (struct usb_device *usb_dev, struct usb_hcd *hcd)
+static int register_root_hub(struct usb_hcd *hcd)
{
struct device *parent_dev = hcd->self.controller;
+ struct usb_device *usb_dev = hcd->self.root_hub;
const int devnum = 1;
int retval;
- /* hcd->driver->start() reported can_wakeup, probably with
- * assistance from board's boot firmware.
- * NOTE: normal devices won't enable wakeup by default.
- */
- if (hcd->can_wakeup)
- dev_dbg (parent_dev, "supports USB remote wakeup\n");
- hcd->remote_wakeup = hcd->can_wakeup;
-
usb_dev->devnum = devnum;
usb_dev->bus->devnum_next = devnum + 1;
memset (&usb_dev->bus->devmap.devicemap, 0,
set_bit (devnum, usb_dev->bus->devmap.devicemap);
usb_set_device_state(usb_dev, USB_STATE_ADDRESS);
- down (&usb_bus_list_lock);
- usb_dev->bus->root_hub = usb_dev;
+ mutex_lock(&usb_bus_list_lock);
usb_dev->ep0.desc.wMaxPacketSize = __constant_cpu_to_le16(64);
retval = usb_get_device_descriptor(usb_dev, USB_DT_DEVICE_SIZE);
if (retval != sizeof usb_dev->descriptor) {
- usb_dev->bus->root_hub = NULL;
- up (&usb_bus_list_lock);
+ mutex_unlock(&usb_bus_list_lock);
dev_dbg (parent_dev, "can't read %s device descriptor %d\n",
usb_dev->dev.bus_id, retval);
return (retval < 0) ? retval : -EMSGSIZE;
}
- usb_lock_device (usb_dev);
retval = usb_new_device (usb_dev);
- usb_unlock_device (usb_dev);
if (retval) {
- usb_dev->bus->root_hub = NULL;
dev_err (parent_dev, "can't register root hub for %s, %d\n",
usb_dev->dev.bus_id, retval);
}
- up (&usb_bus_list_lock);
+ mutex_unlock(&usb_bus_list_lock);
if (retval == 0) {
spin_lock_irq (&hcd_root_hub_lock);
return retval;
}
-EXPORT_SYMBOL_GPL(usb_hcd_register_root_hub);
+
+void usb_enable_root_hub_irq (struct usb_bus *bus)
+{
+ struct usb_hcd *hcd;
+
+ hcd = container_of (bus, struct usb_hcd, self);
+ if (hcd->driver->hub_irq_enable && !hcd->poll_rh &&
+ hcd->state != HC_STATE_HALT)
+ hcd->driver->hub_irq_enable (hcd);
+}
/*-------------------------------------------------------------------------*/
case USB_SPEED_HIGH: /* ISOC or INTR */
// FIXME adjust for input vs output
if (isoc)
- tmp = HS_USECS (bytecount);
+ tmp = HS_NSECS_ISO (bytecount);
else
- tmp = HS_USECS_ISO (bytecount);
+ tmp = HS_NSECS (bytecount);
return tmp;
default:
pr_debug ("%s: bogus device speed!\n", usbcore_name);
spin_lock_irqsave (&hcd_data_lock, flags);
list_del_init (&urb->urb_list);
spin_unlock_irqrestore (&hcd_data_lock, flags);
- usb_put_dev (urb->dev);
}
* expects usb_submit_urb() to have sanity checked and conditioned all
* inputs in the urb
*/
-static int hcd_submit_urb (struct urb *urb, int mem_flags)
+static int hcd_submit_urb (struct urb *urb, gfp_t mem_flags)
{
int status;
struct usb_hcd *hcd = urb->dev->bus->hcpriv;
else switch (hcd->state) {
case HC_STATE_RUNNING:
case HC_STATE_RESUMING:
- usb_get_dev (urb->dev);
+doit:
list_add_tail (&urb->urb_list, &ep->urb_list);
status = 0;
break;
+ case HC_STATE_SUSPENDED:
+ /* HC upstream links (register access, wakeup signaling) can work
+ * even when the downstream links (and DMA etc) are quiesced; let
+ * usbcore talk to the root hub.
+ */
+ if (hcd->self.controller->power.power_state.event == PM_EVENT_ON
+ && urb->dev->parent == NULL)
+ goto doit;
+ /* FALL THROUGH */
default:
status = -ESHUTDOWN;
break;
goto done;
}
- /* running ~= hc unlink handshake works (irq, timer, etc)
- * halted ~= no unlink handshake is needed
- * suspended, resuming == should never happen
- */
- WARN_ON (!HC_IS_RUNNING (hcd->state) && hcd->state != HC_STATE_HALT);
-
/* insist the urb is still queued */
list_for_each(tmp, &ep->urb_list) {
if (tmp == &urb->urb_list)
* finish unlinking the initial failed usb_set_address()
* or device descriptor fetch.
*/
- if (!hcd->saw_irq && hcd->self.root_hub != urb->dev) {
+ if (!test_bit(HCD_FLAG_SAW_IRQ, &hcd->flags)
+ && hcd->self.root_hub != urb->dev) {
dev_warn (hcd->self.controller, "Unlink after no-IRQ? "
"Controller is probably using the wrong IRQ."
"\n");
- hcd->saw_irq = 1;
+ set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
}
urb->status = status;
hcd = udev->bus->hcpriv;
- WARN_ON (!HC_IS_RUNNING (hcd->state) && hcd->state != HC_STATE_HALT);
+ WARN_ON (!HC_IS_RUNNING (hcd->state) && hcd->state != HC_STATE_HALT &&
+ udev->state != USB_STATE_NOTATTACHED);
local_irq_disable ();
/*-------------------------------------------------------------------------*/
-#ifdef CONFIG_USB_SUSPEND
+#ifdef CONFIG_PM
-static int hcd_hub_suspend (struct usb_bus *bus)
+int hcd_bus_suspend (struct usb_bus *bus)
{
struct usb_hcd *hcd;
+ int status;
hcd = container_of (bus, struct usb_hcd, self);
- if (hcd->driver->hub_suspend)
- return hcd->driver->hub_suspend (hcd);
- return 0;
+ if (!hcd->driver->bus_suspend)
+ return -ENOENT;
+ hcd->state = HC_STATE_QUIESCING;
+ status = hcd->driver->bus_suspend (hcd);
+ if (status == 0)
+ hcd->state = HC_STATE_SUSPENDED;
+ else
+ dev_dbg(&bus->root_hub->dev, "%s fail, err %d\n",
+ "suspend", status);
+ return status;
}
-static int hcd_hub_resume (struct usb_bus *bus)
+int hcd_bus_resume (struct usb_bus *bus)
{
struct usb_hcd *hcd;
+ int status;
hcd = container_of (bus, struct usb_hcd, self);
- if (hcd->driver->hub_resume)
- return hcd->driver->hub_resume (hcd);
- return 0;
+ if (!hcd->driver->bus_resume)
+ return -ENOENT;
+ if (hcd->state == HC_STATE_RUNNING)
+ return 0;
+ hcd->state = HC_STATE_RESUMING;
+ status = hcd->driver->bus_resume (hcd);
+ if (status == 0)
+ hcd->state = HC_STATE_RUNNING;
+ else {
+ dev_dbg(&bus->root_hub->dev, "%s fail, err %d\n",
+ "resume", status);
+ usb_hc_died(hcd);
+ }
+ return status;
}
+/*
+ * usb_hcd_suspend_root_hub - HCD autosuspends downstream ports
+ * @hcd: host controller for this root hub
+ *
+ * This call arranges that usb_hcd_resume_root_hub() is safe to call later;
+ * that the HCD's root hub polling is deactivated; and that the root's hub
+ * driver is suspended. HCDs may call this to autosuspend when their root
+ * hub's downstream ports are all inactive: unpowered, disconnected,
+ * disabled, or suspended.
+ *
+ * The HCD will autoresume on device connect change detection (using SRP
+ * or a D+/D- pullup). The HCD also autoresumes on remote wakeup signaling
+ * from any ports that are suspended (if that is enabled). In most cases,
+ * overcurrent signaling (on powered ports) will also start autoresume.
+ *
+ * Always called with IRQs blocked.
+ */
+void usb_hcd_suspend_root_hub (struct usb_hcd *hcd)
+{
+ struct urb *urb;
+
+ spin_lock (&hcd_root_hub_lock);
+ usb_suspend_root_hub (hcd->self.root_hub);
+
+ /* force status urb to complete/unlink while suspended */
+ if (hcd->status_urb) {
+ urb = hcd->status_urb;
+ urb->status = -ECONNRESET;
+ urb->hcpriv = NULL;
+ urb->actual_length = 0;
+
+ del_timer (&hcd->rh_timer);
+ hcd->poll_pending = 0;
+ hcd->status_urb = NULL;
+ } else
+ urb = NULL;
+ spin_unlock (&hcd_root_hub_lock);
+ hcd->state = HC_STATE_SUSPENDED;
+
+ if (urb)
+ usb_hcd_giveback_urb (hcd, urb, NULL);
+}
+EXPORT_SYMBOL_GPL(usb_hcd_suspend_root_hub);
+
/**
* usb_hcd_resume_root_hub - called by HCD to resume its root hub
* @hcd: host controller for this root hub
* The USB host controller calls this function when its root hub is
* suspended (with the remote wakeup feature enabled) and a remote
* wakeup request is received. It queues a request for khubd to
- * resume the root hub.
+ * resume the root hub (that is, manage its downstream ports again).
*/
void usb_hcd_resume_root_hub (struct usb_hcd *hcd)
{
usb_resume_root_hub (hcd->self.root_hub);
spin_unlock_irqrestore (&hcd_root_hub_lock, flags);
}
+EXPORT_SYMBOL_GPL(usb_hcd_resume_root_hub);
-#else
-void usb_hcd_resume_root_hub (struct usb_hcd *hcd)
-{
-}
#endif
-EXPORT_SYMBOL_GPL(usb_hcd_resume_root_hub);
/*-------------------------------------------------------------------------*/
.buffer_alloc = hcd_buffer_alloc,
.buffer_free = hcd_buffer_free,
.disable = hcd_endpoint_disable,
-#ifdef CONFIG_USB_SUSPEND
- .hub_suspend = hcd_hub_suspend,
- .hub_resume = hcd_hub_resume,
-#endif
};
/*-------------------------------------------------------------------------*/
struct usb_hcd *hcd = __hcd;
int start = hcd->state;
- if (start == HC_STATE_HALT)
+ if (unlikely(start == HC_STATE_HALT ||
+ !test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
return IRQ_NONE;
if (hcd->driver->irq (hcd, r) == IRQ_NONE)
return IRQ_NONE;
- hcd->saw_irq = 1;
- if (hcd->state != start && hcd->state == HC_STATE_HALT)
+ set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
+
+ if (unlikely(hcd->state == HC_STATE_HALT))
usb_hc_died (hcd);
return IRQ_HANDLED;
}
spin_lock_irqsave (&hcd_root_hub_lock, flags);
if (hcd->rh_registered) {
+ hcd->poll_rh = 0;
/* make khubd clean up old urbs and devices */
usb_set_device_state (hcd->self.root_hub,
{
struct usb_hcd *hcd;
- hcd = kcalloc(1, sizeof(*hcd) + driver->hcd_priv_size, GFP_KERNEL);
+ hcd = kzalloc(sizeof(*hcd) + driver->hcd_priv_size, GFP_KERNEL);
if (!hcd) {
dev_dbg (dev, "hcd alloc failed\n");
return NULL;
hcd->self.bus_name = bus_name;
init_timer(&hcd->rh_timer);
+ hcd->rh_timer.function = rh_timer_func;
+ hcd->rh_timer.data = (unsigned long) hcd;
hcd->driver = driver;
hcd->product_desc = (driver->product_desc) ? driver->product_desc :
int usb_add_hcd(struct usb_hcd *hcd,
unsigned int irqnum, unsigned long irqflags)
{
- int retval;
+ int retval;
+ struct usb_device *rhdev;
dev_info(hcd->self.controller, "%s\n", hcd->product_desc);
- /* till now HC has been in an indeterminate state ... */
- if (hcd->driver->reset && (retval = hcd->driver->reset(hcd)) < 0) {
- dev_err(hcd->self.controller, "can't reset\n");
- return retval;
- }
+ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+ /* HC is in reset state, but accessible. Now do the one-time init,
+ * bottom up so that hcds can customize the root hubs before khubd
+ * starts talking to them. (Note, bus id is assigned early too.)
+ */
if ((retval = hcd_buffer_create(hcd)) != 0) {
dev_dbg(hcd->self.controller, "pool alloc failed\n");
return retval;
}
if ((retval = usb_register_bus(&hcd->self)) < 0)
- goto err1;
+ goto err_register_bus;
+
+ if ((rhdev = usb_alloc_dev(NULL, &hcd->self, 0)) == NULL) {
+ dev_err(hcd->self.controller, "unable to allocate root hub\n");
+ retval = -ENOMEM;
+ goto err_allocate_root_hub;
+ }
+ rhdev->speed = (hcd->driver->flags & HCD_USB2) ? USB_SPEED_HIGH :
+ USB_SPEED_FULL;
+ hcd->self.root_hub = rhdev;
+
+ /* wakeup flag init defaults to "everything works" for root hubs,
+ * but drivers can override it in reset() if needed, along with
+ * recording the overall controller's system wakeup capability.
+ */
+ device_init_wakeup(&rhdev->dev, 1);
+ /* "reset" is misnamed; its role is now one-time init. the controller
+ * should already have been reset (and boot firmware kicked off etc).
+ */
+ if (hcd->driver->reset && (retval = hcd->driver->reset(hcd)) < 0) {
+ dev_err(hcd->self.controller, "can't setup\n");
+ goto err_hcd_driver_setup;
+ }
+
+ /* NOTE: root hub and controller capabilities may not be the same */
+ if (device_can_wakeup(hcd->self.controller)
+ && device_can_wakeup(&hcd->self.root_hub->dev))
+ dev_dbg(hcd->self.controller, "supports USB remote wakeup\n");
+
+ /* enable irqs just before we start the controller */
if (hcd->driver->irq) {
char buf[8], *bufp = buf;
hcd->irq_descr, hcd)) != 0) {
dev_err(hcd->self.controller,
"request interrupt %s failed\n", bufp);
- goto err2;
+ goto err_request_irq;
}
hcd->irq = irqnum;
dev_info(hcd->self.controller, "irq %s, %s 0x%08llx\n", bufp,
if ((retval = hcd->driver->start(hcd)) < 0) {
dev_err(hcd->self.controller, "startup error %d\n", retval);
- goto err3;
+ goto err_hcd_driver_start;
}
+ /* starting here, usbcore will pay attention to this root hub */
+ rhdev->bus_mA = min(500u, hcd->power_budget);
+ if ((retval = register_root_hub(hcd)) != 0)
+ goto err_register_root_hub;
+
+ if (hcd->uses_new_polling && hcd->poll_rh)
+ usb_hcd_poll_rh_status(hcd);
return retval;
- err3:
+err_register_root_hub:
+ hcd->driver->stop(hcd);
+err_hcd_driver_start:
if (hcd->irq >= 0)
free_irq(irqnum, hcd);
- err2:
+err_request_irq:
+err_hcd_driver_setup:
+ hcd->self.root_hub = NULL;
+ usb_put_dev(rhdev);
+err_allocate_root_hub:
usb_deregister_bus(&hcd->self);
- err1:
+err_register_bus:
hcd_buffer_destroy(hcd);
return retval;
}
spin_lock_irq (&hcd_root_hub_lock);
hcd->rh_registered = 0;
spin_unlock_irq (&hcd_root_hub_lock);
+
+ mutex_lock(&usb_bus_list_lock);
usb_disconnect(&hcd->self.root_hub);
+ mutex_unlock(&usb_bus_list_lock);
+
+ hcd->poll_rh = 0;
+ del_timer_sync(&hcd->rh_timer);
hcd->driver->stop(hcd);
hcd->state = HC_STATE_HALT;
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_USB_MON) || defined(CONFIG_USB_MON_MODULE)
+#if defined(CONFIG_USB_MON)
struct usb_mon_operations *mon_ops;
git://git.onelab.eu / linux-2.6.git / blobdiff