*/
#include <linux/device.h>
+#include <linux/signal.h>
+#include <linux/platform_device.h>
+
#include <asm/mach-types.h>
#include <asm/hardware.h>
#include <asm/arch/pxa-regs.h>
-
-
-#define PMM_NPS_MODE 1
-#define PMM_GLOBAL_MODE 2
-#define PMM_PERPORT_MODE 3
+#include <asm/arch/ohci.h>
#define PXA_UHC_MAX_PORTNUM 3
#define UHCRHPS(x) __REG2( 0x4C000050, (x)<<2 )
-static int pxa27x_ohci_pmm_state;
-
/*
PMM_NPS_MODE -- PMM Non-power switching mode
Ports are powered continuously.
*/
static int pxa27x_ohci_select_pmm( int mode )
{
- pxa27x_ohci_pmm_state = mode;
-
switch ( mode ) {
case PMM_NPS_MODE:
UHCRHDA |= RH_A_NPS;
"Invalid mode %d, set to non-power switch mode.\n",
mode );
- pxa27x_ohci_pmm_state = PMM_NPS_MODE;
UHCRHDA |= RH_A_NPS;
}
return 0;
}
-/*
- If you select PMM_PERPORT_MODE, you should set the port power
- */
-static int pxa27x_ohci_set_port_power( int port )
-{
- if ( (pxa27x_ohci_pmm_state==PMM_PERPORT_MODE)
- && (port>0) && (port<PXA_UHC_MAX_PORTNUM) ) {
- UHCRHPS(port) |= 0x100;
- return 0;
- }
- return -1;
-}
-
-/*
- If you select PMM_PERPORT_MODE, you should set the port power
- */
-static int pxa27x_ohci_clear_port_power( int port )
-{
- if ( (pxa27x_ohci_pmm_state==PMM_PERPORT_MODE)
- && (port>0) && (port<PXA_UHC_MAX_PORTNUM) ) {
- UHCRHPS(port) |= 0x200;
- return 0;
- }
-
- return -1;
-}
-
extern int usb_disabled(void);
/*-------------------------------------------------------------------------*/
-static void pxa27x_start_hc(struct platform_device *dev)
+static int pxa27x_start_hc(struct device *dev)
{
+ int retval = 0;
+ struct pxaohci_platform_data *inf;
+
+ inf = dev->platform_data;
+
pxa_set_cken(CKEN10_USBHOST, 1);
UHCHR |= UHCHR_FHR;
while (UHCHR & UHCHR_FSBIR)
cpu_relax();
- /* This could be properly abstracted away through the
- device data the day more machines are supported and
- their differences can be figured out correctly. */
- if (machine_is_mainstone()) {
- /* setup Port1 GPIO pin. */
- pxa_gpio_mode( 88 | GPIO_ALT_FN_1_IN); /* USBHPWR1 */
- pxa_gpio_mode( 89 | GPIO_ALT_FN_2_OUT); /* USBHPEN1 */
-
- /* Set the Power Control Polarity Low and Power Sense
- Polarity Low to active low. Supply power to USB ports. */
- UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
- ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE);
- }
+ if (inf->init)
+ retval = inf->init(dev);
+
+ if (retval < 0)
+ return retval;
UHCHR &= ~UHCHR_SSE;
UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);
+
+ /* Clear any OTG Pin Hold */
+ if (PSSR & PSSR_OTGPH)
+ PSSR |= PSSR_OTGPH;
+
+ return 0;
}
-static void pxa27x_stop_hc(struct platform_device *dev)
+static void pxa27x_stop_hc(struct device *dev)
{
+ struct pxaohci_platform_data *inf;
+
+ inf = dev->platform_data;
+
+ if (inf->exit)
+ inf->exit(dev);
+
UHCHR |= UHCHR_FHR;
udelay(11);
UHCHR &= ~UHCHR_FHR;
* through the hotplug entry's driver_data.
*
*/
-int usb_hcd_pxa27x_probe (const struct hc_driver *driver,
- struct platform_device *dev)
+int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device *pdev)
{
int retval;
struct usb_hcd *hcd;
+ struct pxaohci_platform_data *inf;
- if (dev->resource[1].flags != IORESOURCE_IRQ) {
+ inf = pdev->dev.platform_data;
+
+ if (!inf)
+ return -ENODEV;
+
+ if (pdev->resource[1].flags != IORESOURCE_IRQ) {
pr_debug ("resource[1] is not IORESOURCE_IRQ");
return -ENOMEM;
}
- hcd = usb_create_hcd (driver, &dev->dev, "pxa27x");
+ hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x");
if (!hcd)
return -ENOMEM;
- hcd->rsrc_start = dev->resource[0].start;
- hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
+ hcd->rsrc_start = pdev->resource[0].start;
+ hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
pr_debug("request_mem_region failed");
goto err2;
}
- pxa27x_start_hc(dev);
+ if ((retval = pxa27x_start_hc(&pdev->dev)) < 0) {
+ pr_debug("pxa27x_start_hc failed");
+ goto err3;
+ }
/* Select Power Management Mode */
- pxa27x_ohci_select_pmm( PMM_PERPORT_MODE );
-
- /* If choosing PMM_PERPORT_MODE, we should set the port power before we use it. */
- if (pxa27x_ohci_set_port_power(1) < 0)
- printk(KERN_ERR "Setting port 1 power failed.\n");
+ pxa27x_ohci_select_pmm(inf->port_mode);
- if (pxa27x_ohci_clear_port_power(2) < 0)
- printk(KERN_ERR "Setting port 2 power failed.\n");
-
- if (pxa27x_ohci_clear_port_power(3) < 0)
- printk(KERN_ERR "Setting port 3 power failed.\n");
+ if (inf->power_budget)
+ hcd->power_budget = inf->power_budget;
ohci_hcd_init(hcd_to_ohci(hcd));
- retval = usb_add_hcd(hcd, dev->resource[1].start, SA_INTERRUPT);
+ retval = usb_add_hcd(hcd, pdev->resource[1].start, SA_INTERRUPT);
if (retval == 0)
return retval;
- pxa27x_stop_hc(dev);
+ pxa27x_stop_hc(&pdev->dev);
+ err3:
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
* context, normally "rmmod", "apmd", or something similar.
*
*/
-void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *dev)
+void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
{
usb_remove_hcd(hcd);
- pxa27x_stop_hc(dev);
+ pxa27x_stop_hc(&pdev->dev);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);
+ /* The value of NDP in roothub_a is incorrect on this hardware */
+ ohci->num_ports = 3;
+
if ((ret = ohci_init(ohci)) < 0)
return ret;
*/
.hub_status_data = ohci_hub_status_data,
.hub_control = ohci_hub_control,
-#ifdef CONFIG_USB_SUSPEND
- .hub_suspend = ohci_hub_suspend,
- .hub_resume = ohci_hub_resume,
+#ifdef CONFIG_PM
+ .bus_suspend = ohci_bus_suspend,
+ .bus_resume = ohci_bus_resume,
#endif
+ .start_port_reset = ohci_start_port_reset,
};
/*-------------------------------------------------------------------------*/
-static int ohci_hcd_pxa27x_drv_probe(struct device *dev)
+static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
{
- struct platform_device *pdev = to_platform_device(dev);
- int ret;
-
pr_debug ("In ohci_hcd_pxa27x_drv_probe");
if (usb_disabled())
return -ENODEV;
- ret = usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev);
- return ret;
+ return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev);
}
-static int ohci_hcd_pxa27x_drv_remove(struct device *dev)
+static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
{
- struct platform_device *pdev = to_platform_device(dev);
- struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
usb_hcd_pxa27x_remove(hcd, pdev);
+ platform_set_drvdata(pdev, NULL);
return 0;
}
-static int ohci_hcd_pxa27x_drv_suspend(struct device *dev, pm_message_t state, u32 level)
+#ifdef CONFIG_PM
+static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state)
{
-// struct platform_device *pdev = to_platform_device(dev);
-// struct usb_hcd *hcd = dev_get_drvdata(dev);
- printk("%s: not implemented yet\n", __FUNCTION__);
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+
+ if (time_before(jiffies, ohci->next_statechange))
+ msleep(5);
+ ohci->next_statechange = jiffies;
+
+ pxa27x_stop_hc(&pdev->dev);
+ hcd->state = HC_STATE_SUSPENDED;
+ pdev->dev.power.power_state = PMSG_SUSPEND;
return 0;
}
-static int ohci_hcd_pxa27x_drv_resume(struct device *dev, u32 level)
+static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev)
{
-// struct platform_device *pdev = to_platform_device(dev);
-// struct usb_hcd *hcd = dev_get_drvdata(dev);
- printk("%s: not implemented yet\n", __FUNCTION__);
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+ int status;
+
+ if (time_before(jiffies, ohci->next_statechange))
+ msleep(5);
+ ohci->next_statechange = jiffies;
+
+ if ((status = pxa27x_start_hc(&pdev->dev)) < 0)
+ return status;
+
+ pdev->dev.power.power_state = PMSG_ON;
+ usb_hcd_resume_root_hub(hcd);
return 0;
}
+#endif
-static struct device_driver ohci_hcd_pxa27x_driver = {
- .name = "pxa27x-ohci",
- .bus = &platform_bus_type,
+static struct platform_driver ohci_hcd_pxa27x_driver = {
.probe = ohci_hcd_pxa27x_drv_probe,
.remove = ohci_hcd_pxa27x_drv_remove,
+#ifdef CONFIG_PM
.suspend = ohci_hcd_pxa27x_drv_suspend,
- .resume = ohci_hcd_pxa27x_drv_resume,
+ .resume = ohci_hcd_pxa27x_drv_resume,
+#endif
+ .driver = {
+ .name = "pxa27x-ohci",
+ },
};
static int __init ohci_hcd_pxa27x_init (void)
pr_debug ("block sizes: ed %d td %d\n",
sizeof (struct ed), sizeof (struct td));
- return driver_register(&ohci_hcd_pxa27x_driver);
+ return platform_driver_register(&ohci_hcd_pxa27x_driver);
}
static void __exit ohci_hcd_pxa27x_cleanup (void)
{
- driver_unregister(&ohci_hcd_pxa27x_driver);
+ platform_driver_unregister(&ohci_hcd_pxa27x_driver);
}
module_init (ohci_hcd_pxa27x_init);
git://git.onelab.eu / linux-2.6.git / blobdiff