fedora core 6 1.2949 + vserver 2.2.0

[linux-2.6.git] / include / asm-arm / arch-at91rm9200 / board.h

diff --git a/include/asm-arm/arch-at91rm9200/board.h b/include/asm-arm/arch-at91rm9200/board.h
index 2e7d113..768e0fc 100644 (file)
--- a/include/asm-arm/arch-at91rm9200/board.h
+++ b/include/asm-arm/arch-at91rm9200/board.h
@@ -20,7 +20,7 @@
 
 /*
  * These are data structures found in platform_device.dev.platform_data,
- * and describing board-specfic data needed by drivers.  For example,
+ * and describing board-specific data needed by drivers.  For example,
  * which pin is used for a given GPIO role.
  *
  * In 2.6, drivers should strongly avoid board-specific knowledge so
@@ -31,12 +31,9 @@
 #ifndef __ASM_ARCH_BOARD_H
 #define __ASM_ARCH_BOARD_H
 
- /* Clocks */
-extern unsigned long at91_master_clock;
-
- /* Serial Port */
-extern int at91_serial_map[AT91_NR_UART];
-extern int at91_console_port;
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
 
  /* USB Device */
 struct at91_udc_data {
@@ -51,13 +48,14 @@ struct at91_cf_data {
        u8      det_pin;                /* Card detect */
        u8      vcc_pin;                /* power switching */
        u8      rst_pin;                /* card reset */
+       u8      chipselect;             /* EBI Chip Select number */
 };
 extern void __init at91_add_device_cf(struct at91_cf_data *data);
 
  /* MMC / SD */
 struct at91_mmc_data {
        u8              det_pin;        /* card detect IRQ */
-       unsigned        is_b:1;         /* uses B side (vs A) */
+       unsigned        slot_b:1;       /* uses Slot B */
        unsigned        wire4:1;        /* (SD) supports DAT0..DAT3 */
        u8              wp_pin;         /* (SD) writeprotect detect */
        u8              vcc_pin;        /* power switching (high == on) */
@@ -77,4 +75,43 @@ struct at91_usbh_data {
 };
 extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
 
+ /* NAND / SmartMedia */
+struct at91_nand_data {
+       u8              enable_pin;     /* chip enable */
+       u8              det_pin;        /* card detect */
+       u8              rdy_pin;        /* ready/busy */
+       u8              ale;            /* address line number connected to ALE */
+       u8              cle;            /* address line number connected to CLE */
+       u8              bus_width_16;   /* buswidth is 16 bit */
+       struct mtd_partition* (*partition_info)(int, int*);
+};
+extern void __init at91_add_device_nand(struct at91_nand_data *data);
+
+ /* I2C*/
+extern void __init at91_add_device_i2c(void);
+
+ /* SPI */
+extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
+
+ /* Serial */
+struct at91_uart_config {
+       unsigned short  console_tty;    /* tty number of serial console */
+       unsigned short  nr_tty;         /* number of serial tty's */
+       short           tty_map[];      /* map UART to tty number */
+};
+extern struct platform_device *atmel_default_console_device;
+extern void __init at91_init_serial(struct at91_uart_config *config);
+
+struct atmel_uart_data {
+       short           use_dma_tx;     /* use transmit DMA? */
+       short           use_dma_rx;     /* use receive DMA? */
+       void __iomem    *regs;          /* virtual base address, if any */
+};
+extern void __init at91_add_device_serial(void);
+
+ /* LEDs */
+extern u8 at91_leds_cpu;
+extern u8 at91_leds_timer;
+extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
+
 #endif