#define DRCMRTXPCDR DRCMR12
#define DRCMRRXSSDR DRCMR13
#define DRCMRTXSSDR DRCMR14
+#define DRCMRRXSS2DR DRCMR15
+#define DRCMRTXSS2DR DRCMR16
#define DRCMRRXICDR DRCMR17
#define DRCMRTXICDR DRCMR18
#define DRCMRRXSTRBR DRCMR19
#define DRCMRTXSTTHR DRCMR20
#define DRCMRRXMMC DRCMR21
#define DRCMRTXMMC DRCMR22
+#define DRCMRRXSS3DR DRCMR66
+#define DRCMRTXSS3DR DRCMR67
#define DRCMRUDC(x) DRCMR((x) + 24)
#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */
#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */
#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */
-/* default combinations */
-#define DCMD_RXPCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_RXMCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_TXPCDR (DCMD_INCSRCADDR|DCMD_FLOWTRG|DCMD_BURST32|DCMD_WIDTH4)
-
/*
* UARTs
*/
/* FIXME: This clash with SA1111 defines */
-#ifndef CONFIG_SA1111
+#ifndef _ASM_ARCH_SA1111
+
#define SACR0 __REG(0x40400000) /* Global Control Register */
#define SACR1 __REG(0x40400004) /* Serial Audio I 2 S/MSB-Justified Control Register */
#define SASR0 __REG(0x4040000C) /* Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
#define SAICR __REG(0x40400018) /* Serial Audio Interrupt Clear Register */
#define SADIV __REG(0x40400060) /* Audio Clock Divider Register. */
#define SADR __REG(0x40400080) /* Serial Audio Data Register (TX and RX FIFO access Register). */
-#endif
+#define SACR0_RFTH(x) (x << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_TFTH(x) (x << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_STRF (1 << 5) /* FIFO Select for EFWR Special Function */
+#define SACR0_EFWR (1 << 4) /* Enable EFWR Function */
+#define SACR0_RST (1 << 3) /* FIFO, i2s Register Reset */
+#define SACR0_BCKD (1 << 2) /* Bit Clock Direction */
+#define SACR0_ENB (1 << 0) /* Enable I2S Link */
+#define SACR1_ENLBF (1 << 5) /* Enable Loopback */
+#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */
+#define SACR1_DREC (1 << 3) /* Disable Recording Function */
+#define SACR1_AMSL (1 << 1) /* Specify Alternate Mode */
+
+#define SASR0_I2SOFF (1 << 7) /* Controller Status */
+#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */
+#define SASR0_TUR (1 << 5) /* Tx FIFO Underrun */
+#define SASR0_RFS (1 << 4) /* Rx FIFO Service Request */
+#define SASR0_TFS (1 << 3) /* Tx FIFO Service Request */
+#define SASR0_BSY (1 << 2) /* I2S Busy */
+#define SASR0_RNE (1 << 1) /* Rx FIFO Not Empty */
+#define SASR0_TNF (1 << 0) /* Tx FIFO Not Empty */
+
+#define SAICR_ROR (1 << 6) /* Clear Rx FIFO Overrun Interrupt */
+#define SAICR_TUR (1 << 5) /* Clear Tx FIFO Underrun Interrupt */
+
+#define SAIMR_ROR (1 << 6) /* Enable Rx FIFO Overrun Condition Interrupt */
+#define SAIMR_TUR (1 << 5) /* Enable Tx FIFO Underrun Condition Interrupt */
+#define SAIMR_RFS (1 << 4) /* Enable Rx FIFO Service Interrupt */
+#define SAIMR_TFS (1 << 3) /* Enable Tx FIFO Service Interrupt */
+
+#endif
/*
* AC97 Controller registers
#define POCR __REG(0x40500000) /* PCM Out Control Register */
#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define PICR __REG(0x40500004) /* PCM In Control Register */
#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MCCR __REG(0x40500008) /* Mic In Control Register */
#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define GCR __REG(0x4050000C) /* Global Control Register */
+#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
#define POSR __REG(0x40500010) /* PCM Out Status Register */
#define POSR_FIFOE (1 << 4) /* FIFO error */
+#define POSR_FSR (1 << 2) /* FIFO Service Request */
#define PISR __REG(0x40500014) /* PCM In Status Register */
#define PISR_FIFOE (1 << 4) /* FIFO error */
+#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define PISR_FSR (1 << 2) /* FIFO Service Request */
#define MCSR __REG(0x40500018) /* Mic In Status Register */
#define MCSR_FIFOE (1 << 4) /* FIFO error */
+#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MCSR_FSR (1 << 2) /* FIFO Service Request */
#define GSR __REG(0x4050001C) /* Global Status Register */
#define GSR_CDONE (1 << 19) /* Command Done */
#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */
#define GSR_SCR (1 << 9) /* Secondary Codec Ready */
#define GSR_PCR (1 << 8) /* Primary Codec Ready */
-#define GSR_MINT (1 << 7) /* Mic In Interrupt */
+#define GSR_MCINT (1 << 7) /* Mic In Interrupt */
#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
+#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */
#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
#define MOCR __REG(0x40500100) /* Modem Out Control Register */
#define MOCR_FEIE (1 << 3) /* FIFO Error */
+#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MICR __REG(0x40500108) /* Modem In Control Register */
#define MICR_FEIE (1 << 3) /* FIFO Error */
+#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define MOSR __REG(0x40500110) /* Modem Out Status Register */
#define MOSR_FIFOE (1 << 4) /* FIFO error */
+#define MOSR_FSR (1 << 2) /* FIFO Service Request */
#define MISR __REG(0x40500118) /* Modem In Status Register */
#define MISR_FIFOE (1 << 4) /* FIFO error */
+#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MISR_FSR (1 << 2) /* FIFO Service Request */
#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */
#define GPIO31_SYNC 31 /* AC97/I2S sync */
#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */
+#define GPIO32_SYSCLK 32 /* I2S System Clock */
#define GPIO32_MMCCLK 32 /* MMC Clock (PXA270) */
#define GPIO33_nCS_5 33 /* chip select 5 */
#define GPIO34_FFRXD 34 /* FFUART receive */
#define GPIO43_BTTXD 43 /* BTUART transmit data */
#define GPIO44_BTCTS 44 /* BTUART clear to send */
#define GPIO45_BTRTS 45 /* BTUART request to send */
+#define GPIO45_AC97_SYSCLK 45 /* AC97 System Clock */
#define GPIO46_ICPRXD 46 /* ICP receive data */
#define GPIO46_STRXD 46 /* STD_UART receive data */
#define GPIO47_ICPTXD 47 /* ICP transmit data */
#define GPIO78_nCS_2 78 /* chip select 2 */
#define GPIO79_nCS_3 79 /* chip select 3 */
#define GPIO80_nCS_4 80 /* chip select 4 */
+#define GPIO81_NSCLK 81 /* NSSP clock */
+#define GPIO82_NSFRM 82 /* NSSP Frame */
+#define GPIO83_NSTXD 83 /* NSSP transmit */
+#define GPIO84_NSRXD 84 /* NSSP receive */
#define GPIO85_nPCE_1 85 /* Card Enable for Card Space (PXA27x) */
#define GPIO92_MMCDAT0 92 /* MMC DAT0 (PXA27x) */
#define GPIO109_MMCDAT1 109 /* MMC DAT1 (PXA27x) */
#define GPIO_MD_MASK_NR 0x07f
#define GPIO_MD_MASK_DIR 0x080
#define GPIO_MD_MASK_FN 0x300
+#define GPIO_DFLT_LOW 0x400
+#define GPIO_DFLT_HIGH 0x800
#define GPIO1_RTS_MD ( 1 | GPIO_ALT_FN_1_IN)
#define GPIO6_MMCCLK_MD ( 6 | GPIO_ALT_FN_1_OUT)
#define GPIO18_RDY_MD (18 | GPIO_ALT_FN_1_IN)
#define GPIO19_DREQ1_MD (19 | GPIO_ALT_FN_1_IN)
#define GPIO20_DREQ0_MD (20 | GPIO_ALT_FN_1_IN)
-#define GPIO23_SCLK_md (23 | GPIO_ALT_FN_2_OUT)
+#define GPIO23_SCLK_MD (23 | GPIO_ALT_FN_2_OUT)
#define GPIO24_SFRM_MD (24 | GPIO_ALT_FN_2_OUT)
#define GPIO25_STXD_MD (25 | GPIO_ALT_FN_2_OUT)
#define GPIO26_SRXD_MD (26 | GPIO_ALT_FN_1_IN)
#define GPIO27_SEXTCLK_MD (27 | GPIO_ALT_FN_1_IN)
#define GPIO28_BITCLK_AC97_MD (28 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_I2S_MD (28 | GPIO_ALT_FN_2_IN)
+#define GPIO28_BITCLK_IN_I2S_MD (28 | GPIO_ALT_FN_2_IN)
+#define GPIO28_BITCLK_OUT_I2S_MD (28 | GPIO_ALT_FN_1_OUT)
#define GPIO29_SDATA_IN_AC97_MD (29 | GPIO_ALT_FN_1_IN)
#define GPIO29_SDATA_IN_I2S_MD (29 | GPIO_ALT_FN_2_IN)
#define GPIO30_SDATA_OUT_AC97_MD (30 | GPIO_ALT_FN_2_OUT)
#define GPIO30_SDATA_OUT_I2S_MD (30 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT)
+#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN)
+#define GPIO32_SYSCLK_I2S_MD (32 | GPIO_ALT_FN_1_OUT)
#define GPIO32_MMCCLK_MD ( 32 | GPIO_ALT_FN_2_OUT)
#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT)
#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN)
#define GPIO43_BTTXD_MD (43 | GPIO_ALT_FN_2_OUT)
#define GPIO44_BTCTS_MD (44 | GPIO_ALT_FN_1_IN)
#define GPIO45_BTRTS_MD (45 | GPIO_ALT_FN_2_OUT)
+#define GPIO45_SYSCLK_AC97_MD (45 | GPIO_ALT_FN_1_OUT)
#define GPIO46_ICPRXD_MD (46 | GPIO_ALT_FN_1_IN)
#define GPIO46_STRXD_MD (46 | GPIO_ALT_FN_2_IN)
#define GPIO47_ICPTXD_MD (47 | GPIO_ALT_FN_2_OUT)
#define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT)
#define GPIO79_pSKTSEL_MD (79 | GPIO_ALT_FN_1_OUT)
#define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT)
+#define GPIO81_NSSP_CLK_OUT (81 | GPIO_ALT_FN_1_OUT)
+#define GPIO81_NSSP_CLK_IN (81 | GPIO_ALT_FN_1_IN)
+#define GPIO82_NSSP_FRM_OUT (82 | GPIO_ALT_FN_1_OUT)
+#define GPIO82_NSSP_FRM_IN (82 | GPIO_ALT_FN_1_IN)
+#define GPIO83_NSSP_TX (83 | GPIO_ALT_FN_1_OUT)
+#define GPIO83_NSSP_RX (83 | GPIO_ALT_FN_2_IN)
+#define GPIO84_NSSP_TX (84 | GPIO_ALT_FN_1_OUT)
+#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN)
#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT)
#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT)
#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT)
#define GPIO110_MMCCS1_MD (111 | GPIO_ALT_FN_1_OUT)
#define GPIO112_MMCCMD_MD (112 | GPIO_ALT_FN_1_OUT)
#define GPIO113_AC97_RESET_N_MD (113 | GPIO_ALT_FN_2_OUT)
-
+#define GPIO117_I2CSCL_MD (117 | GPIO_ALT_FN_1_OUT)
+#define GPIO118_I2CSDA_MD (118 | GPIO_ALT_FN_1_IN)
/*
* Power Manager
#define PVCR_CommandDelay (0xf80)
#define PCFR_PI2C_EN (0x1 << 6)
-#define PSSR_OTGPH (1 << 7) /* OTG Peripheral control Hold */
+#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */
#define PSSR_RDH (1 << 5) /* Read Disable Hold */
#define PSSR_PH (1 << 4) /* Peripheral Control Hold */
#define PSSR_VFS (1 << 2) /* VDD Fault Status */
#define RCSR_WDR (1 << 1) /* Watchdog Reset */
#define RCSR_HWR (1 << 0) /* Hardware Reset */
+#define PWER_GPIO(Nb) (1 << Nb) /* GPIO [0..15] wake-up enable */
+#define PWER_GPIO0 PWER_GPIO (0) /* GPIO [0] wake-up enable */
+#define PWER_GPIO1 PWER_GPIO (1) /* GPIO [1] wake-up enable */
+#define PWER_GPIO2 PWER_GPIO (2) /* GPIO [2] wake-up enable */
+#define PWER_GPIO3 PWER_GPIO (3) /* GPIO [3] wake-up enable */
+#define PWER_GPIO4 PWER_GPIO (4) /* GPIO [4] wake-up enable */
+#define PWER_GPIO5 PWER_GPIO (5) /* GPIO [5] wake-up enable */
+#define PWER_GPIO6 PWER_GPIO (6) /* GPIO [6] wake-up enable */
+#define PWER_GPIO7 PWER_GPIO (7) /* GPIO [7] wake-up enable */
+#define PWER_GPIO8 PWER_GPIO (8) /* GPIO [8] wake-up enable */
+#define PWER_GPIO9 PWER_GPIO (9) /* GPIO [9] wake-up enable */
+#define PWER_GPIO10 PWER_GPIO (10) /* GPIO [10] wake-up enable */
+#define PWER_GPIO11 PWER_GPIO (11) /* GPIO [11] wake-up enable */
+#define PWER_GPIO12 PWER_GPIO (12) /* GPIO [12] wake-up enable */
+#define PWER_GPIO13 PWER_GPIO (13) /* GPIO [13] wake-up enable */
+#define PWER_GPIO14 PWER_GPIO (14) /* GPIO [14] wake-up enable */
+#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */
+#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */
+
/*
* SSP Serial Port Registers
+ * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
+ * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
*/
-#define SSCR0 __REG(0x41000000) /* SSP Control Register 0 */
-#define SSCR1 __REG(0x41000004) /* SSP Control Register 1 */
-#define SSSR __REG(0x41000008) /* SSP Status Register */
-#define SSITR __REG(0x4100000C) /* SSP Interrupt Test Register */
-#define SSDR __REG(0x41000010) /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
+ /* Common PXA2xx bits first */
#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
+#define SSCR0_TIM (1 << 23) /* Transmit FIFO Under Run Interrupt Mask */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO Over Run interrupt Mask */
+#define SSCR0_NCS (1 << 21) /* Network Clock Select */
+#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */
+
+/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
+#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
+#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
+#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
+#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
+#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
+#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
+#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
+#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
+#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
+#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
+#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
+#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
+#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
+#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
+#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */
+#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
+#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
+
+#define SSSR_BCE (1 << 23) /* Bit Count Error */
+#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
+#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
+#define SSSR_EOC (1 << 20) /* End Of Chain */
+#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
+#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
+
+#define SSPSP_DMYSTOP(x) (x << 23) /* Dummy Stop */
+#define SSPSP_SFRMWDTH(x) (x << 16) /* Serial Frame Width */
+#define SSPSP_SFRMDLY(x) (x << 9) /* Serial Frame Delay */
+#define SSPSP_DMYSTRT(x) (x << 7) /* Dummy Start */
+#define SSPSP_STRTDLY(x) (x << 4) /* Start Delay */
+#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
+#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
+#define SSPSP_SCMODE(x) (x << 0) /* Serial Bit Rate Clock Mode */
+
+
+#define SSCR0_P1 __REG(0x41000000) /* SSP Port 1 Control Register 0 */
+#define SSCR1_P1 __REG(0x41000004) /* SSP Port 1 Control Register 1 */
+#define SSSR_P1 __REG(0x41000008) /* SSP Port 1 Status Register */
+#define SSITR_P1 __REG(0x4100000C) /* SSP Port 1 Interrupt Test Register */
+#define SSDR_P1 __REG(0x41000010) /* (Write / Read) SSP Port 1 Data Write Register/SSP Data Read Register */
+
+/* Support existing PXA25x drivers */
+#define SSCR0 SSCR0_P1 /* SSP Control Register 0 */
+#define SSCR1 SSCR1_P1 /* SSP Control Register 1 */
+#define SSSR SSSR_P1 /* SSP Status Register */
+#define SSITR SSITR_P1 /* SSP Interrupt Test Register */
+#define SSDR SSDR_P1 /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
+
+/* PXA27x ports */
+#if defined (CONFIG_PXA27x)
+#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
+#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
+#define SSCR0_P2 __REG(0x41700000) /* SSP Port 2 Control Register 0 */
+#define SSCR1_P2 __REG(0x41700004) /* SSP Port 2 Control Register 1 */
+#define SSSR_P2 __REG(0x41700008) /* SSP Port 2 Status Register */
+#define SSITR_P2 __REG(0x4170000C) /* SSP Port 2 Interrupt Test Register */
+#define SSDR_P2 __REG(0x41700010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
+#define SSTO_P2 __REG(0x41700028) /* SSP Port 2 Time Out Register */
+#define SSPSP_P2 __REG(0x4170002C) /* SSP Port 2 Programmable Serial Protocol */
+#define SSCR0_P3 __REG(0x41900000) /* SSP Port 3 Control Register 0 */
+#define SSCR1_P3 __REG(0x41900004) /* SSP Port 3 Control Register 1 */
+#define SSSR_P3 __REG(0x41900008) /* SSP Port 3 Status Register */
+#define SSITR_P3 __REG(0x4190000C) /* SSP Port 3 Interrupt Test Register */
+#define SSDR_P3 __REG(0x41900010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
+#define SSTO_P3 __REG(0x41900028) /* SSP Port 3 Time Out Register */
+#define SSPSP_P3 __REG(0x4190002C) /* SSP Port 3 Programmable Serial Protocol */
+#else /* PXA255 (only port 2) and PXA26x ports*/
+#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
+#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
+#define SSCR0_P2 __REG(0x41400000) /* SSP Port 2 Control Register 0 */
+#define SSCR1_P2 __REG(0x41400004) /* SSP Port 2 Control Register 1 */
+#define SSSR_P2 __REG(0x41400008) /* SSP Port 2 Status Register */
+#define SSITR_P2 __REG(0x4140000C) /* SSP Port 2 Interrupt Test Register */
+#define SSDR_P2 __REG(0x41400010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
+#define SSTO_P2 __REG(0x41400028) /* SSP Port 2 Time Out Register */
+#define SSPSP_P2 __REG(0x4140002C) /* SSP Port 2 Programmable Serial Protocol */
+#define SSCR0_P3 __REG(0x41500000) /* SSP Port 3 Control Register 0 */
+#define SSCR1_P3 __REG(0x41500004) /* SSP Port 3 Control Register 1 */
+#define SSSR_P3 __REG(0x41500008) /* SSP Port 3 Status Register */
+#define SSITR_P3 __REG(0x4150000C) /* SSP Port 3 Interrupt Test Register */
+#define SSDR_P3 __REG(0x41500010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
+#define SSTO_P3 __REG(0x41500028) /* SSP Port 3 Time Out Register */
+#define SSPSP_P3 __REG(0x4150002C) /* SSP Port 3 Programmable Serial Protocol */
+#endif
+
+#define SSCR0_P(x) (*(((x) == 1) ? &SSCR0_P1 : ((x) == 2) ? &SSCR0_P2 : ((x) == 3) ? &SSCR0_P3 : NULL))
+#define SSCR1_P(x) (*(((x) == 1) ? &SSCR1_P1 : ((x) == 2) ? &SSCR1_P2 : ((x) == 3) ? &SSCR1_P3 : NULL))
+#define SSSR_P(x) (*(((x) == 1) ? &SSSR_P1 : ((x) == 2) ? &SSSR_P2 : ((x) == 3) ? &SSSR_P3 : NULL))
+#define SSITR_P(x) (*(((x) == 1) ? &SSITR_P1 : ((x) == 2) ? &SSITR_P2 : ((x) == 3) ? &SSITR_P3 : NULL))
+#define SSDR_P(x) (*(((x) == 1) ? &SSDR_P1 : ((x) == 2) ? &SSDR_P2 : ((x) == 3) ? &SSDR_P3 : NULL))
+#define SSTO_P(x) (*(((x) == 1) ? &SSTO_P1 : ((x) == 2) ? &SSTO_P2 : ((x) == 3) ? &SSTO_P3 : NULL))
+#define SSPSP_P(x) (*(((x) == 1) ? &SSPSP_P1 : ((x) == 2) ? &SSPSP_P2 : ((x) == 3) ? &SSPSP_P3 : NULL))
/*
* MultiMediaCard (MMC) controller
#define CKEN13_FICP (1 << 13) /* FICP Unit Clock Enable */
#define CKEN12_MMC (1 << 12) /* MMC Unit Clock Enable */
#define CKEN11_USB (1 << 11) /* USB Unit Clock Enable */
+#define CKEN10_ASSP (1 << 10) /* ASSP (SSP3) Clock Enable */
#define CKEN10_USBHOST (1 << 10) /* USB Host Unit Clock Enable */
#define CKEN9_OSTIMER (1 << 9) /* OS Timer Unit Clock Enable */
+#define CKEN9_NSSP (1 << 9) /* NSSP (SSP2) Clock Enable */
#define CKEN8_I2S (1 << 8) /* I2S Unit Clock Enable */
#define CKEN7_BTUART (1 << 7) /* BTUART Unit Clock Enable */
#define CKEN6_FFUART (1 << 6) /* FFUART Unit Clock Enable */
git://git.onelab.eu / linux-2.6.git / blobdiff