vserver 1.9.5.x5

[linux-2.6.git] / include / asm-arm / arch-sa1100 / ide.h

diff --git a/include/asm-arm/arch-sa1100/ide.h b/include/asm-arm/arch-sa1100/ide.h
index bc44296..2153538 100644 (file)
--- a/include/asm-arm/arch-sa1100/ide.h
+++ b/include/asm-arm/arch-sa1100/ide.h
@@ -14,6 +14,8 @@
 #include <asm/hardware.h>
 #include <asm/mach-types.h>
 
+#error "This code is broken and needs update to match with current ide support"
+
 
 /*
  * Set up a hw structure for a specified data port, control port and IRQ.
@@ -47,10 +49,6 @@ static inline void ide_init_hwif_ports(hw_regs_t *hw, unsigned long data_port,
                *irq = 0;
 }
 
-#ifdef CONFIG_SA1100_TRIZEPS
-#include <asm/arch/trizeps.h>
-#endif
-
 /*
  * This registers the standard ports for this architecture with the IDE
  * driver.
@@ -58,55 +56,7 @@ static inline void ide_init_hwif_ports(hw_regs_t *hw, unsigned long data_port,
 static __inline__ void
 ide_init_default_hwifs(void)
 {
-    if( machine_is_empeg() ){
-#ifdef CONFIG_SA1100_EMPEG
-       hw_regs_t hw;
-
-       /* First, do the SA1100 setup */
-
-       /* PCMCIA IO space */
-       MECR=0x21062106;
-
-        /* Issue 3 is much neater than issue 2 */
-       GPDR&=~(EMPEG_IDE1IRQ|EMPEG_IDE2IRQ);
-
-       /* Interrupts on rising edge: lines are inverted before they get to
-           the SA */
-       set_GPIO_IRQ_edge( (EMPEG_IDE1IRQ|EMPEG_IDE2IRQ), GPIO_FALLING_EDGE );
-
-       /* Take hard drives out of reset */
-       GPSR=(EMPEG_IDERESET);
-
-       /* Sonja and her successors have two IDE ports. */
-       /* MAC 23/4/1999, swap these round so that the left hand
-          hard disk is hda when viewed from the front. This
-          doesn't match the silkscreen however. */
-       ide_init_hwif_ports(&hw, PCMCIA_IO_0_BASE + 0x40, PCMCIA_IO_0_BASE + 0x78, NULL);
-       hw.irq = EMPEG_IRQ_IDE2;
-       ide_register_hw(&hw);
-       ide_init_hwif_ports(&hw, PCMCIA_IO_0_BASE + 0x00, PCMCIA_IO_0_BASE + 0x38, NULL);
-       hw.irq = ,EMPEG_IRQ_IDE1;
-       ide_register_hw(&hw);
-#endif
-    }
-
-    else if( machine_is_victor() ){
-#ifdef CONFIG_SA1100_VICTOR
-       hw_regs_t hw;
-
-       /* Enable appropriate GPIOs as interrupt lines */
-       GPDR &= ~GPIO_GPIO7;
-       set_GPIO_IRQ_edge( GPIO_GPIO7, GPIO_RISING_EDGE );
-
-       /* set the pcmcia interface timing */
-       MECR = 0x00060006;
-
-       ide_init_hwif_ports(&hw, PCMCIA_IO_0_BASE + 0x1f0, PCMCIA_IO_0_BASE + 0x3f6, NULL);
-       hw.irq = IRQ_GPIO7;
-       ide_register_hw(&hw);
-#endif
-    }
-    else if (machine_is_lart()) {
+    if (machine_is_lart()) {
 #ifdef CONFIG_SA1100_LART
         hw_regs_t hw;
 
@@ -121,25 +71,6 @@ ide_init_default_hwifs(void)
        ide_init_hwif_ports(&hw, PCMCIA_IO_0_BASE + 0x0000, PCMCIA_IO_0_BASE + 0x1000, NULL);
         hw.irq = LART_IRQ_IDE;
         ide_register_hw(&hw);
-#endif
-    }
-    else if( machine_is_trizeps() ){
-#ifdef CONFIG_SA1100_TRIZEPS
-       hw_regs_t hw;
-
-       /* Enable appropriate GPIOs as interrupt lines */
-       GPDR &= ~GPIO_GPIO(TRIZEPS_IRQ_IDE);
-       set_irq_type( TRIZEPS_IRQ_IDE, IRQT_RISING );
-
-       /* set the pcmcia interface timing */
-       //MECR = 0x00060006; // Done on trizeps init
-
-       /* Take hard drives out of reset */
-       GPSR = GPIO_GPIO(TRIZEPS_IRQ_IDE);
-
-       ide_init_hwif_ports(&hw, TRIZEPS_IDE_CS0 + 0, TRIZEPS_IDE_CS1 + 6, NULL);
-       hw.irq = TRIZEPS_IRQ_IDE;
-       ide_register_hw(&hw, NULL);
 #endif
     }
 }